Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 3499
2017-05-23
WIP Standard
AS5680B
This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: - Physical envelope of the fuze well at the interface with the fuze. - Load bearing surfaces of the fuze well. - Physical envelope of the fuze and its connector. - Mechanical features (e.g., clocking feature). - Connector type, size, location and orientation. - Retaining ring and its mechanical features (e.g., thread, tool interface). - Physical envelope of the retaining ring at the interface with the fuze. - Physical space available for installation tools. - Torque that the installation tool shall be capable of providing. This standard does not address: - Materials used or their properties. - Protective finish. - Physical environment of the weapon. - Explosive interface or features (e.g., insensitive munitions (IM) mitigation). - Charging tube. - Torque on the retaining ring or loads on the load bearing surfaces.
CURRENT
2017-05-19
Standard
J3008_201705
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.
CURRENT
2017-05-18
Standard
ARP6157
The lubricant performance capability for aero propulsion drive systems is derived from the physical properties of the oil and performance attributes associated with the chemical properties of the oil. Physical properties, such as viscosity, pressure-viscosity coefficient and full-film traction coefficient are inherent properties of the lubricating fluid. Chemical attributes are critical for the formation of protective boundary lubricating films on the surfaces to prevent wear and scuffing. These attributes are also associated with surface initiated fatigue (micropitting). To assure performance and to provide required information for engineering design, methodology for at least five oil properties are being studied: (1) pressure-viscosity coefficient, (2) full-film traction coefficient, (3) scuffing resistance, (4) wear resistance; and (5) micropitting propensity.
CURRENT
2017-05-18
Standard
AS20708/81B
No Scope Available
CURRENT
2017-05-18
Standard
AIR6130A
14-day material test to determine the cyclic effects of runway deicing compounds on cadmium plated parts.
2017-05-17
WIP Standard
AS2592A
This Aerospace Material Specification covers components of rotary flap assemblies, assembled by peening processors, to be used with portable equipment for peening of metal parts.
2017-05-16
WIP Standard
J1842
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
2017-05-10
WIP Standard
J1939-76
This document provides the technical requirements for implementing the SAE J1939 Functional Safety Communication Protocol in a manner determined suitable for meeting industry applicable functional safety standards.
CURRENT
2017-05-10
Standard
AIR5872A
This SAE Aerospace Information Report (AIR) presents an overview of the application and control of fixed and variable displacement pumps with the emphasis on the controls most commonly used on variable displacement pumps. It describes various options to control the operation of hydraulic pumps in terms of controlling the pump output pressure and/or flow and assisting in the selection of the pump.
CURRENT
2017-05-04
Standard
ARP378D
This document presents criteria for design and location of passenger reading lights in commercial aircraft. For LED reading light requirements, see ARP5873, titled: LED Passenger Reading Light Assembly.
CURRENT
2017-05-04
Standard
ARP1328C
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a. uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b. uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c. standardization of specific types of interlock systems and actuation systems, d. a standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e. a standard method for testing these systems.
2017-05-03
WIP Standard
J2383
This SAE Recommended Practice establishes uniform Installation Parameters for desiccant Air Dryers for vehicles with compressed air systems.
2017-05-02
WIP Standard
J2384
This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.
CURRENT
2017-04-28
Standard
J1287_201704
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the exhaust sound pressure levels of motorcycles under stationary conditions. Since initial publication, it has been successfully applied to regulation and monitoring of sound pressure levels of off-highway vehicles, and that remains its recommended application. Users of SAE J1287 for the purpose of roadside enforcement of sound pressure levels for on-highway motorcycles have reported difficulties with its implementation in that application. In response, SAE J2825 was developed, and is recommended for measurement of exhaust sound pressure levels of stationary on-highway motorcycles. Care must be taken not to confuse stationary sound pressure levels with total motorcycle sound pressure levels. This test does not evaluate total motorcycle sound during operation. For this purpose, SAE J331 or SAE J47 is recommended.
CURRENT
2017-04-27
Standard
J2743_201704
This SAE Recommended Practice is intended to describe a procedure for rating the size of single-stage reciprocating air compressors. It describes the conditions that can be used for testing and it defines a standardized rating expressed in SLPM (SCFM).
2017-04-21
WIP Standard
ARP1971D
This SAE Aerospace Recommended Practice (ARP) covers requirements for a self-propelled, boom type aerial device, equipped with an aircraft deicing/anti-icing fluid spraying system. The unit shall be highly maneuverable for deicing all exterior surfaces of commercial aircraft, of sizes agreed upon between purchaser and manufacturer, in accordance with SAE ARP4737. The vehicle will also be used for aircraft maintenance and inspection. The vehicle shall be suitable for day and night operations.
2017-04-20
WIP Standard
AS9104/1A
These requirements are applicable to IAQG global sectors when utilizing Aerospace Industry Controlled Other Party (ICOP) schemes for the assessment and certidication of supplier quality systems in accordance with the requirements AS/EN/SJAC 9104.
CURRENT
2017-04-18
Standard
J2966_201704
This document outlines general requirements for the use of CFD methods for aerodynamic simulation of medium and heavy commercial ground vehicles weighing more than 10 000lbs. The document provides guidance for aerodynamic simulation with CFD methods to support current vehicle characterization, vehicle development, vehicle concept development and vehicle component development. The guidelines presented in the document are related to Navier-Stokes and Lattice-Boltzmann based solvers. This document is only valid for the classes of CFD methods and applications mentioned. Other classes of methods and applications may or may not be appropriate to simulate the aerodynamics of medium and heavy commercial ground vehicle weighing more than 10 000lbs.
2017-04-14
WIP Standard
J2684
This Recommended Practice is derived from the FMVSS 105 vehicle test and applies to two-axle multipurpose passenger vehicles, trucks and buses with a GVWR above 4 540 kg (10 000 lbs) equipped with hydraulic service brakes. There are two main test sequences: Development Test Sequence for generic test conditions when not all information is available or when an assessment of brake output at different inputs are required, and FMVSS Test Sequence when vehicle parameters for brake pressure as a function of brake pedal input force and vehicle-specific loading and brake distribution are available. The test sequences are derived from the Federal Motor Vehicle Safety Standard 105 (and 121 for optional sections) as single-ended inertia-dynamometer test procedures when using the appropriate brake hardware and test parameters.
2017-04-13
WIP Standard
AIR5875A
This SAE Aerospace Information Report (AIR) outlines comprehensive aircraft flight control system fault isolation methodology that has proven to be effective. The methodology presented in this Information Report has been used in several successful fault isolation efforts on military aircraft.
CURRENT
2017-04-13
Standard
AIR36105B
The present SAE Aerospace Information Report (AIR) provides a list of the main government regulations, SAE and international standards, and standing industry recommendations applying to air cargo unit load devices (pallets, nets, and containers) to be loaded with either baggage or freight on board civil transport aircraft.
2017-04-12
WIP Standard
J2601
SAE J2601 establishes the protocol and process limits for hydrogen fueling of light dutyand medium duty vehicles. These process limits (including the fuel delivery temperature, the maximum fuel flow rate, the rate of pressure increase and the ending pressure) are affected by factors such as ambient temperature, fuel delivery temperature and initial pressure in the vehicle’s compressed hydrogen storage system. SAE J2601 establishes standard fueling protocols based on either a look-up table approach utilizing a fixed pressure ramp rate, or a formula based approach utilizing a dynamic pressure ramp rate continuously calculated throughout the fill. Both protocols allow for fueling with communications or without communications. The table-based protocol provides a fixed end-of-fill pressure target, whereas the formula-based protocol calculates the end-of-fill pressure target continuously.
2017-04-11
WIP Standard
ARP6539
This SAE Aerospace Recommended Practice (ARP) provides a process for the verification and validation of monitors used in flight control, utility control, and related components and systems. It is intended to serve as a system specific companion document to SAE ARP 4754.
2017-04-11
WIP Standard
AIR6920
This AIR is for use by OEM's and Suppliers developing process gate checklists for highly integrated, complex flight control and vehicle management systems to support the life cycle development validation and verification activities prescribed by ARP4754.
2017-04-10
WIP Standard
J2848/3
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of ground vehicle CTIS. Systems of this type allow the driver to select the operational tire pressure set point (TPSP) based on off-highway conditions, and, upon returning to highway operations, maintain the inflation pressure to the vehicle specified level. These systems are recommended to address all serviceable tires as originally installed on a vehicle by the OEM and/or specialty vehicle manufacturer, and, for the aftermarket (including replacement or spare parts) are recommended (but optional) to address all tire/rim combinations installed after initial vehicle sale or in-use dates.
2017-04-07
WIP Standard
J1252
The scope of this SAE Recommended Practice is sufficiently broad that it encompasses the full range of full-scale medium and heavy duty vehicles represented as either full-scale or reduced-scale wind tunnel models. The document provides guidance for wind tunnel testing to support current vehicle characterization, vehicle development, vehicle concept development, and vehicle component development.
2017-04-06
WIP Standard
J2848/1
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems, and recommended maintenance practices within the known operating environments. This document is applicable to all axle and all wheel combinations for single unit powered vehicles exceeding 7257 kg (16 000 US lb) gross vehicle weight rating (GVWR), and multi-unit vehicle combinations, up to three (3) towed units, which use an SAE J560 connector for power and/or communication, or equivalent successor connector technology, or which use a suitable capacity wireless solution. Examples of included single chassis vehicles would be – utility and delivery vans, tow trucks, rack trucks, buses, recreational vehicles, fuel trucks, trash trucks, dump trucks, cement trucks, and tractors.
CURRENT
2017-04-06
Standard
J3059_201704
This SAE Information Report describes the testing and reporting procedures that may be used to evaluate and document the excursion of a worker or civilian when transported in a seated and restrained position in the patient compartment of a ground ambulance when exposed to a front, side, or rear impact. Its purpose is to provide seating and occupant restraint manufacturers, ambulance builders, and end-users with testing procedures and documentation methods needed to identify head travel paths in crash loading events. This is a component level test. The seating system is tested in free space to measure maximum head travel paths. The purpose is not to identify stay out zones. Rather, the goal is to provide ambulance manufacturers with the data needed to design safer and functionally sound workstations for Emergency Medical Service workers so that workers are better able to safely perform patient care tasks in a moving ambulance.
2017-04-05
WIP Standard
ARP6078A
The Aerospace Recommended Practices of this document are intended for nitrogen-based Flammability Reduction Means (FRM) implemented on transport category, turbine powered airplanes. The recommended practices herein, therefore, relate only to the transport category aircraft, and focus specifically on contemporary inerting systems equipment. Such systems are referred to a Fuel Tank Inerting Systems (FTIS) in this document. This document does not cover the following: - Military aircraft applications - Air separation technologies other than hollow fiber membrane (HFM) and pressure swing adsorption (PSA) - Inerting of conventional unheated wing tanks or aircraft dry bays - Expected future technology solutions for the generation of inert gas. The advice contained in this document is aimed towards providing aircraft manufacturers with guidance on the key issues associated with contemporary aircraft fuel tank inerting systems to supplement the guidance in FAA Advisory Circular AC 25.981-2.
CURRENT
2017-04-05
Standard
ARP6156
The lubricant performance capability for aero propulsion drive systems is derived from the physical properties of the oil and the chemical attributes associated with the oil formulation. All properties, such as viscosity, pressure-viscosity coefficient and full-film traction coefficient are inherent properties of the lubricating fluid. Chemical attributes are critical for the formation of protective boundary lubricating films on the surfaces to prevent wear and scuffing. To assure performance and to provide needed information for engineering design, test methodologies for at least five oil properties or attributes are being addressed: (1) pressure-viscosity coefficient, (2) full-film traction coefficient, (3) scuffing resistance, (4) wear resistance, and (5) micropitting propensity. While viscosity versus temperature data are readily available, the above five properties or attributes must be measured under relevant conditions for aero propulsion hardware systems.
Viewing 121 to 150 of 3499

Filter

  • Standard
    3499