Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 3439
CURRENT
2017-06-26
Standard
J2836/4_201706
This SAE Information Report J2836/4 establishes diagnostic use cases between plug-in electric vehicles and the EV Supply Equipment (EVSE). As Plug-In Vehicles (PEV) are deployed and include both Plug-In Hybrid Electric (PHEV) and Battery Electric (BEV) variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document will describe the general information required for diagnostics and J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
2017-06-22
WIP Standard
AS5714A
This SAE Aerospace Standard (AS) prescribes the Minimum Performance Standards (MPS) for wheel, brake, and wheel and brake assemblies to be used on aircraft certificated under 14 CFR Parts 23, 27, and 29. Compliance with this specification is not considered approval for installation on any aircraft.
2017-06-22
WIP Standard
J2711/2
This SAE Recommended Practice was established to provide an accurate, uniform and reproducible procedure for simulating use of MD/HD conventional vehicles and hybrid-electric vehicles (HEVs), as well as plug-in hybrid-electric vehicles (PHEVs) and battery electric vehicles (BEVs) on powertrain dynamometers for the purpose of measuring emissions and fuel economy. This document does not specify which emissions constituents to measure (e.g., HC, CO, NOx, PM, CO2), as that decision will depend on the objectives of the tester. While the main focus of this procedure is for calculating fuel and energy consumption, it is anticipated that emissions may also be recorded during execution of this procedure. It should be noted that most MD/HD powertrains addressed in this document would be powered by engines that are certified separately for emissions. The engine certification procedure appears in the Code of Federal Regulations, Title 40-§86 and §1065.
2017-06-21
WIP Standard
AIR1419C
This document addresses many of the significant issues associated with effects of inlet total-pressure distortion on turbine-engine performance and stability. It provides a review of the development of techniques used to assess engine stability margins in the presence of inlet total-pressure distortion. Specific performance and stability issues that are covered by this document include total-pressure recovery and turbulence effects and steady and dynamic inlet total-pressure distortion.
2017-06-19
WIP Standard
J1992
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
2017-06-19
WIP Standard
J2836/6
This SAE Information Report SAE J2836/6™ establishes use cases for communication between plug-in electric vehicles and the EVSE, for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the Wireless EV Supply Equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them.
2017-06-19
WIP Standard
J2847/6
This SAE Recommended Practice SAE J2847-6 establishes requirements and specifications for communications messages between wirelessly charged electric vehicles and the wireless charger. Where relevant, this document notes, but does not formally specify, interactions between the vehicle and vehicle operator. This is the 1st version of this document and captures the initial objectives of the SAE task force. The intent of step 1 is to record as much information on “what we think works” and publish. The effort continues however, to step 2 that allows public review for additional comments and viewpoints, while the task force also continues additional testing and early implementation. Results of step 2 effort will then be incorporated into updates of this document and lead to a republished version. The next revision will address the harmonization between SAE J2847-6 and ISO/IEC 15118-7 to ensure interoperability.
2017-06-19
WIP Standard
J2931/6
This SAE Information Report J2931/6 establishes the requirements for physical and data link layer communications between Plug-in Electric Vehicles (PEV) and the Electric Vehicle Supply Equipment (EVSE).
CURRENT
2017-06-16
Standard
CPYM2_17MX800V
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2017-06-16
Standard
CPYM1_17MX825V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
CURRENT
2017-06-16
Standard
CPYM1_17MX800V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
2017-06-15
WIP Standard
J1939-17
This document defines a physical layer having a higher bandwidth capacity than the classic physical layers defined for SAE J1939-14 by using flexible data rates. CAN controllers are now available which support the Flexible Data Rate Frame Format as defined in ISO 11898-1:2015. These controllers and compatible high speed transceivers are required for use on SAE J1939-17 networks. This SAE Recommended Practice is intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
2017-06-12
WIP Standard
ARP6954
This SAE Aerospace Resource Document (ARD) document covers the requirements for a self-propelled GRV, intended for use at airports to collect spent aircraft de-icing fluid (ADF) from the surface of de-icing areas. This unit will recover de-icing fluid from the surface, which will be stored in a containment unit on the vehicle. The GRV must be capable of night and day operations in all weather conditions, as required.
CURRENT
2017-06-09
Standard
ARP1804B
This SAE Aerospace Recommended Practice (ARP) outlines the design and performance requirements for a battery-powered electric tow tractor for the handling of baggage or cargo trailers in airline service. The use of “shall” in this document indicates a mandatory requirement. The use of “should” indicates a recommendation or that which is advised but not required.
2017-06-08
WIP Standard
AS598A
This SAE Aerospace Standard (AS) defines the materials, apparatus and procedure for microscopic sizing and counting of particulate contamination of fluid power systems by membrane filtration using microscopic counting.
CURRENT
2017-06-07
Standard
J820_201706
This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.
CURRENT
2017-06-07
Standard
J765_201706
This SAE Standard may be used for all revolving cranes wherein the capacity of the crane to support loads is based on its resistance to overturning. It is not applicable to cranes wherein the capacity of the crane is based on factors other than stability.
CURRENT
2017-06-07
Standard
J2494/2_201706
This SAE Standard covers general dimensional specifications for non-metallic body reusable push to connect tube fittings for use in the piping of air brake systems on automotive vehicles. This type of fitting is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J2494-3 for the performance requirements of Reusable (push-to-connect) fittings intended for use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.106.
CURRENT
2017-06-05
Standard
J293_201706
This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers, and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to: a. Vehicle classification b. Vehicle load c. Percent grade d. Application force
CURRENT
2017-05-30
Standard
J2494/1_201705
This SAE Standard covers general and dimensional specifications for brass bodied reusable Push to Connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. See SAE J2494-3 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation, National Highway Traffic Safety Administration (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) 571.
2017-05-29
WIP Standard
J2704
This SAE Recommended Practice describes a test method for determining the vertical force and deflection properties of a non-rolling tire and the associated contact patch length and width. The method applies to any tire so long as the equipment is properly scaled to conduct the measurements for the intended test tire. The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE-Herein, road load models are models for predicting forces applied to the vehicle spindles during operation over irregular pavements. Within the context of this Recommended Practice, forces applied to the pavement are not considered.
2017-05-29
WIP Standard
J2718
This SAE Recommended Practice describes application of two closely related test procedures, which together determine the linear range longitudinal and lateral stiffnesses of a statically loaded non-rotating tire. The procedures apply to any tire so long as the equipment is properly sized to correctly conduct the measurements for the intended test tire. The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE: Herein, road load models are models for predicting forces applied to the vehicle spindles during operation over irregular pavements. Within the context of this document, forces applied to the pavement are not considered.
CURRENT
2017-05-25
Standard
AIR805D
The purpose of this information report is to present the factors that affect the design and development of aircraft jet blast windshield rain removal systems. Rain removal system design will generally be unique to specific aircraft. Design of these systems typically requires a preliminary design for the system based on available empirical data to be followed with a laboratory development program and a flight test validation program. Published windshield rain removal performance test data is available only for limited windshield configurations.
2017-05-23
WIP Standard
AIR6027A
The information presented in this AIR is intended to provide designers of armed unmanned systems with guidelines that may be applied to ensure safe integration and operation of weapons on unmanned platforms. The guidelines have been developed from experiences gained in the design and operation of weapons on manned aircraft that have been accepted by relevant safety authorities in the USA and Europe and proven effective over many years. Whilst the guidelines have been developed from experience with aircraft operations, the concepts are considered equally applicable to non-aircraft systems, such as those used on the surface or undersea environments.
2017-05-23
WIP Standard
AS5680B
This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: - Physical envelope of the fuze well at the interface with the fuze. - Load bearing surfaces of the fuze well. - Physical envelope of the fuze and its connector. - Mechanical features (e.g., clocking feature). - Connector type, size, location and orientation. - Retaining ring and its mechanical features (e.g., thread, tool interface). - Physical envelope of the retaining ring at the interface with the fuze. - Physical space available for installation tools. - Torque that the installation tool shall be capable of providing. This standard does not address: - Materials used or their properties. - Protective finish. - Physical environment of the weapon. - Explosive interface or features (e.g., insensitive munitions (IM) mitigation). - Charging tube. - Torque on the retaining ring or loads on the load bearing surfaces.
2017-05-23
WIP Standard
AS47642B
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760C. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies. For validation of aircraft designed to MIL-STD-1760B Notice 3 AS47641 Issued 1999-08 applies.
2017-05-22
WIP Standard
J1939DA
This document is intended to supplement the J1939 documents by offering the J1939 information in a form that can be sorted and search for easier use. The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. It also includes the supporting descriptions and figures previously published in the SAE J1939-71 document.
CURRENT
2017-05-19
Standard
J3008_201705
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.
CURRENT
2017-05-18
Standard
AIR6130A
14-day material test to determine the cyclic effects of runway deicing compounds on cadmium plated parts.
CURRENT
2017-05-18
Standard
ARP6157
The lubricant performance capability for aero propulsion drive systems is derived from the physical properties of the oil and performance attributes associated with the chemical properties of the oil. Physical properties, such as viscosity, pressure-viscosity coefficient and full-film traction coefficient are inherent properties of the lubricating fluid. Chemical attributes are critical for the formation of protective boundary lubricating films on the surfaces to prevent wear and scuffing. These attributes are also associated with surface initiated fatigue (micropitting). To assure performance and to provide required information for engineering design, methodology for at least five oil properties are being studied: (1) pressure-viscosity coefficient, (2) full-film traction coefficient, (3) scuffing resistance, (4) wear resistance; and (5) micropitting propensity.
Viewing 1 to 30 of 3439

Filter