Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 64
2017-11-20
WIP Standard
J3014
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
2017-08-22
WIP Standard
J2357
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements and design guidelines for electronic devices.
2016-09-27
WIP Standard
J283
The lift capacity can be determined by Section 4 and/or Section 5. When the results are recorded, the test method shall be identified.
2015-02-13
WIP Standard
ARP4955B
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances.
2014-08-07
WIP Standard
J1739
This FMEA Standard describes Potential Failure Mode and Effects Analysis in Design (DFMEA) and Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, ranking charts, and worksheets. As a Standard, this document contains requirements "must" and recommendations "should" to guide the user through the FMEA process. The FMEA process and documentation must comply with this Standard as well as any corporate policy concerning this Standard. Documented rationale and agreement with the customer is necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
CURRENT
2014-07-24
Standard
J2382_201407
Traditional methods of photometry rely on the use of a goniometer to rotate the test item around two axes at right angles. This method is satisfactory for most situations but has certain disadvantages: Point-by-point measurements with a goniometer may be slow. With more advanced requirements, particularly for headlamps, where the entire beam pattern is of concern, isocandela measurements are becoming increasingly needed. Such testing can be very time consuming. For production quality assurance, the speed of a goniometer may not allow testing to keep pace with the production line if a large quantity of lamps must be sampled. High Intensity Discharge (HID) lamps are becoming commonly used. Such lamps are orientation sensitive, changing in both lumen output and intensity distribution when tilted. This can introduce significant inaccuracies in test results when testing is performed using a goniometer.
2014-06-26
WIP Standard
J3100
This recommended practice describes the application of digital cameras to measurement of photometric quantities in the photometric laboratory.
CURRENT
2014-06-16
Standard
J1892_201406
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
CURRENT
2014-06-05
Standard
J1773_201406
This SAE Recommended Practice establishes the minimum interface compatibility requirements for electric vehicle (EV) inductively coupled charging for North America. This part of the specification is applicable to manually connected inductive charging for Levels 1 and 2 power transfer. Requirements for Level 3 compatibility are contained in Appendix B. Recommended software interface messaging requirements are contained in Appendix A. This type of inductively coupled charging is generally intended for transferring power at frequencies significantly higher than power line frequencies. This part of the specification is not applicable to inductive coupling schemes that employ automatic connection methods or that are intended for transferring power at power line frequencies.
CURRENT
2014-02-26
Standard
J2293/1_201402
SAE J2293 establishes requirements for Electric Vehicles (EV) and the off-board Electric Vehicle Supply Equipment (EVSE) used to transfer electrical energy to an EV from an Electric Utility Power System (Utility) in North America. This document defines, either directly or by reference, all characteristics of the total EV Energy Transfer System (EV-ETS) necessary to insure the functional interoperability of an EV and EVSE of the same physical system architecture. The ETS, regardless of architecture, is responsible for the conversion of AC electrical energy into DC electrical energy that can be used to charge the Storage Battery of an EV, as shown in Figure 1. The different physical ETS system architectures are identified by the form of the energy that is transferred between the EV and the EVSE, as shown in Figure 2. It is possible for an EV and EVSE to support more than one architecture.
CURRENT
2014-02-21
Standard
J2191_201402
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
CURRENT
2013-12-10
Standard
J2380_201312
This SAE Recommended Practice describes the vibration durability testing of a single battery (test unit) consisting of either an electric vehicle battery module or an electric vehicle battery pack. For statistical purposes, multiple samples would normally be subjected to such testing. Additionally, some test units may be subjected to life cycle testing (either after or during vibration testing) to determine the effects of vibration on battery life. Such life testing is not described in this procedure; SAE J2288 may be used for this purpose as applicable. Finally, impact testing, such as crash and pothole, is not included in this procedure.
CURRENT
2013-03-26
Standard
J3014_201303
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
CURRENT
2013-03-05
Standard
J2886_201303
SAE J2886 Design Review Based on Failure Modes (DRBFM) Recommended Practice is intended for Automotive and Non-Automotive applications. It describes the basic principles and processes of DRBFM including planning, preparation, change point FMEA, design reviews, decisions based on actions completed, and feedback loops to other processes, such as design, validation and process guidelines (Appendix B - DRBFM Process Map). The intent of each fundamental step of the DRBFM methodology is presented. It is intended for use by organizations whose product development processes currently (or intend to) use Failure Mode & Effects Analysis (FMEA) or DRBFM as a tool for assessing the potential risk and reliability of system elements (product or process) or as part of their product improvement processes.
HISTORICAL
2013-03-05
Standard
J2999_201303
This SAE Standard provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies. Lamps can be evaluated using the method described in SAE J3333; however, no lamp is subjected to both methods.
CURRENT
2012-11-01
Standard
J2357_201211
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements and design guidelines for electronic devices.
HISTORICAL
2012-10-15
Standard
J1772_201210
This SAE Recommended Practice covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in North America. This document defines a common EV/PHEV and supply equipment vehicle conductive charging method including operational requirements and the functional and dimensional requirements for the vehicle inlet and mating connector.
CURRENT
2012-07-23
Standard
J1877_201207
This SAE Recommended Practice describes the basic content requirements, bar code specifications, and functional test specifications of the vehicle identification number (VIN) label. On the vehicle, the VIN label is to be mounted in a readily accessible location for use of a bar-code scanning device.
2012-05-07
WIP Standard
J4000
SAE J4000 is a tool to identify and measure best practice in the implementation of lean operation in a manufacturing organization. Implementation of lean operation is defined as the process of eliminating waste exhibited in an organization's value stream. Best practice in this process is Level 3 conduct as described in the standard's component statements. A description of the levels of implementation is: Level 0 The component is not in place at all or there are major inconsistencies in implementation. Level 1 The component is in place but there are minor inconsistencies in implementation. Level 2 The component is fully in place and effectively implemented. Level 3 The component is fully in place, effectively implemented and exhibits improvement in execution over the past 12 months. A procedure for evaluation and scoring of each component will be included in the SAE J4001 Implementation of Lean Operation User Manual.
2012-05-07
WIP Standard
J4001
SAE J4001 provides instruction for evaluating levels of compliance to SAE J4000. Component text (Sections 4 to 9) from SAE J4000 is included for convenience during the evaluation process. Applicable definitions and references are contained in SAE J4000. SAE J4000 tests lean implementation within a manufacturing organization and includes those areas of direct overlap with the organization's suppliers and customers. If applied to each consecutive organizational link, an enterprise level evaluation can be made. SAE J4001 relates the following approximate topic percentages to the implementation process as a whole: Element 4 Management/Trust 25% Element 5 People 25% Element 6 Information Element 7 Supplier/Organization/Customer 25% (combined) Element 8 Product Element 9 Process/Flow 25% SAE J4001 is to be applied on a specific component basis. Each of the fifty-two components tests part of, one, or multiples of the specific requirements of lean implementation.
HISTORICAL
2011-06-16
Standard
J577_201106
This SAE Recommended Practice provides procedures, and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
HISTORICAL
2011-05-02
Standard
J1555_201105
This SAE Recommended Practice applies to all portions of the vehicle, but design efforts should focus on components and systems with the highest contribution to the overall average repair cost (see 3.7). The costs to be minimized include not only insurance premiums, but also out-of-pocket costs incurred by the owner. Damageability, repairability, serviceability and diagnostics are inter-related. Some repairability, serviceability and diagnostics operations may be required for collision or comprehensive loss-related causes only, some operations for non-collision-related causes only (warranty, scheduled maintenance, non-scheduled maintenance, etc.), and some for both causes. The scope of this document deals with only those operations that involve collision and comprehensive insurance loss repairs.
HISTORICAL
2010-01-07
Standard
J2191_201001
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
CURRENT
2009-04-02
Standard
J283_200904
The lift capacity can be determined by Section 4 and/or Section 5. When the results are recorded, the test method shall be identified.
CURRENT
2009-01-15
Standard
J1739_200901
This FMEA Standard describes Potential Failure Mode and Effects Analysis in Design (DFMEA) and Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, ranking charts, and worksheets. As a Standard, this document contains requirements “must” and recommendations “should” to guide the user through the FMEA process. The FMEA process and documentation must comply with this Standard as well as any corporate policy concerning this Standard. Documented rationale and agreement with the customer is necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
HISTORICAL
2007-12-06
Standard
J1330_200712
The purpose of this SAE Information Report is to list and explain major equipment, instrumentation, and procedure variables which can affect inter-laboratory differences and repeatability of photometric measurements of various lighting devices listed in SAE Technical Reports. The accuracy guidelines listed in the report are for the purpose of controlling variables that are not a direct function of the lighting device being measured. The control of these individual variables is necessary to control the overall accuracy of photometric measurements. These accuracy guidelines apply to the measurement of the luminous intensities and reflected intensities of devices at the specified geometrically distributed test points and areas. These guidelines do not apply to photometric equipment used to measure license plate lamps.
CURRENT
2007-08-22
Standard
ARP4955A
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances. This revision (Revision A) is also intended to provide suggested guidelines for synthesizing tire dynamic data necessary for landing gear shimmy analyses.
HISTORICAL
2004-01-30
Standard
J2191_200401
This SAE Recommended Practice defines a recommended practice for implementing circuit identification for the circuits of the power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer's primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is crossreferenced to a specified subsystem of the power and signal distribution system identified in Section 5.
CURRENT
2003-05-15
Standard
J708_200305
The purpose of this SAE Standard is to define test conditions, give a description of the tests to be made, specify data to be obtained, show formulas and calculations, define terms, and establish a uniform method of reporting so that performance data obtained on various makes and models of tractors, tested in accordance with this document, will be comparable regardless of where the test is made. It is obvious, because of the many present day tractor models available in a number of types with numerous items of special or optional equipment, that the scope of this document must be limited to obtaining and reporting only the most significant of widely used performance data.
HISTORICAL
2002-12-13
Standard
J2191_200212
This SAE Recommended Practice defines a recommended practice for implementing circuit identification for the circuits of the power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer's primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5. Purpose This document will provide a common method of identifying circuit function for commercially available Class 8 vehicles. It will guide the service technician in diagnosing vehicle electrical subsystems. The identification method will supplement component OEM circuit identification for each major subsystem.
Viewing 1 to 30 of 64

Filter

  • Standard
    64