Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 495
2017-09-26
WIP Standard
G17AC
This specification covers a titanium alloy in the form of sheet from 0.020 to 0.1874 inches (0.508 to 4.760 mm), inclusive, nominal thickness.
2017-09-22
WIP Standard
AMS4900Q
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4914G
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inches in thickness. These products have been used typically in applications requiring high strength-to-weight ratio and stability up to 550 °F (288 °C), but usage is not limited to such applications. Parts are typically formed in the solution heat treated condition and subsequently precipitation heat treated to final condition.
2017-09-22
WIP Standard
AMS4919J
This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2017-09-22
WIP Standard
AMS4918P
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm), inclusive.
2017-09-22
WIP Standard
AMS4937E
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and of flash welded rings and stock for flash welded rings.
2017-09-22
WIP Standard
AMSH81200E
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
AMS4967M
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-05
WIP Standard
AMS03_28PT3A
This SAE Standard specifies the requirements for coatings of titanium nitride on non-corrosion resisting and corrosion resisting steels, cast irons and other suitable materials. Standard engineering items such as coated tools, drills and dies would not normally be included.
CURRENT
2017-08-29
Standard
AMS4941G
This specification covers one grade of commercially pure titanium in the form of welded tubing.
2017-07-19
WIP Standard
G17AB
This specification covers a titnaium alloy in the form of forgings 4.4 inches (111.76 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
CURRENT
2017-07-19
Standard
AMS4940C
This specification covers one grade (Grade 1) of commercially-pure titanium in the form of sheet, strip, and plate up through a thickness of 1.000 inch (25.40 mm) inclusive.
CURRENT
2017-07-11
Standard
AMS2631E
This specification covers the procedure for ultrasonic inspection of wrought titanium and titanium alloy products 0.25 inch (6.4 mm) and over in cross-section (thickness) or diameter.
CURRENT
2017-06-21
Standard
AMS2249H
This specification defines limits of variation for determining acceptability of the composition of cast or wrought titanium and titanium alloy parts and material acquired from a producer.
CURRENT
2017-06-05
Standard
AS5620B
This SAE Aerospace Standard (AS) shall be used in conjunction with AMS 4946 to provide requirements for qualification testing and for Qualified Products Listing (QPL) and Qualified Manufacturer Listing (QML) for Ti-3Al-2.5V cold worked and stress relieved hydraulic system tubing. The basic tubing shall comply with the requirements of AMS 4946.
2017-05-16
WIP Standard
GA-G17AA
Add ASTM E 539
2017-04-26
WIP Standard
AMS4988D
This specification covers a titanium alloy in the form of sheet, strip, and plate in thicknesses up through 4.000 inches (101.60 mm).
2017-04-26
WIP Standard
AMS7819E
This specification covers an arc-cast molybdenum alloy in the form of round bars. These bars have been used typically for parts requiring high modulus and uniform strength up to 2300 °F (1260 °C) but usage is not limited to such applications. This alloy is not recommended for use in oxidizing atmospheres above 1000 °F (540 °C) unless protected by a suitable coating.
2017-04-26
WIP Standard
AMS4945G
This specification covers a titanium alloy in the form of seamless tubing.
2017-04-26
WIP Standard
AMS4958E
This specification covers a titanium alloy in the form of bars and rod 1.000 inch (25.40 mm) and under in nominal diameter.
2017-04-26
WIP Standard
AMS6905C
This specification covers a titanium alloy in the form of bars and forgings up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2), and forging stock of any size.
2017-04-26
WIP Standard
AMS4905F
This specification covers one type of titanium alloy plate in the beta-annealed condition.
2017-04-26
WIP Standard
AMS6930F
This specification covers a titanium alloy in the form of bars, forgings, and stock for forging.
2017-04-26
WIP Standard
AMS4907L
This specification covers a titanium alloy in the form of sheet, strip, and plate. These products have been used typically for parts requiring a combination of weldability, ductility, and good notch-toughness down to –423 °F (–253 °C), but usage is not limited to such applications. Certain processing procedures and service conditions may cause these products to become subject to stress corrosion cracking; ARP982 recommends practices to minimize such conditions.
Viewing 1 to 30 of 495

Filter

  • Standard
    495