Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 16 of 16
2017-11-17
WIP Standard
J459
The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloys, the strength and dimensional stability of the steel backing (usually SAE 1010) and the strength of the bond between the lining alloy and the backing. This SAE Information Report is primarily concerned with the properties of the lining alloys used in automotive applications, in particular, the crankshaft bearings of the internal combustion engine.
2017-11-15
WIP Standard
J460
Compositions apply to the finished bearing or bearing lining, not necessarily to the alloy at an intermediate processing stage. All values not given as ranges are maxima.
CURRENT
2017-11-09
Standard
AMS2451/12A
This specification covers the engineering requirements and process for brush plating of tin by electrodeposition. It shall be used, in conjunction with AMS2451, for general purpose tin deposits.
CURRENT
2017-11-08
Standard
AMS2434E
This specification covers the requirements for electrodeposited tin-zinc alloy plating.
CURRENT
2017-08-22
Standard
AMS4275E
This specification covers an aluminum alloy in the form of permanent mold castings.
CURRENT
2017-05-25
Standard
AMS4631F
This specification covers one type of aluminum bronze in the form of rods, bars, forgings, and forging stock.
CURRENT
2017-04-20
Standard
AMS4751D
This specification covers a tin-lead alloy in the form of bars, ingots, pellets, ribbon, and round wire.
CURRENT
2017-04-07
Standard
AMS4750E
This specification covers a tin-lead solder in the form of wire, strip, bars, and pigs.
CURRENT
2016-09-20
Standard
AMS4625H
This specification covers one type of bronze in the form of bars and rods of any size, and tubing over 1.00 inches (25.4 mm) in nominal outer diameter (see 8.5).
CURRENT
2016-08-04
Standard
AMS4720H
This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter (see 8.4).
CURRENT
2016-02-29
Standard
AMS3678/14A
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 40% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/6B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 60% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2014-10-01
Standard
GEIAGEB0002
This Bulletin provides a brief description of tin whisker formation and describes various methods recommended by government and industry to reduce the risk of tin whisker-induced failures in electronic hardware. It is not a mandate nor does it contain any requirements. A tin whisker is a single crystal that emerges from tin-finished surfaces. Tin whiskers can pose a serious reliability risk to electronic assemblies that have pure tin finish. The general risks fall into several categories: [1, 2, 3, 8, 16] Short Circuits: The whisker can create a short circuit, either by 1) growing from an area at one potential to an area at another or 2) breaking free and later bridging these areas. In some cases, these shorts may be permanent and cause catastrophic system failures. A transient short may result if the available current exceeds the fusing current of the whisker, and the whisker can fuse open.
CURRENT
1991-10-01
Standard
J460_199110
Compositions apply to the finished bearing or bearing lining, not necessarily to the alloy at an intermediate processing stage. All values not given as ranges are maxima. (See Tables 1 through 5.)
CURRENT
1991-10-01
Standard
J459_199110
The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloy, the strength and dimensional stability of the steel backing (usually SAE 1010) and the strength of the bond between the lining alloy and the backing. This SAE Information Report is primarily concerned with the properties of the lining alloys used in automotive applications, in particular, the crankshaft bearings of the internal combustion engine.
HISTORICAL
1974-10-01
Standard
J460E_197410
Compositions apply to the finished bearing or bearing lining, not necessarily to the alloy at an intermediate processing stage. All values not given as ranges are maxima.
Viewing 1 to 16 of 16

    Filter

    • Standard
      16