Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 50
2017-04-26
WIP Standard
AS1145D
This specification covers minimum requirements for brake temperature monitoring equipment whenever used on any type and model of civil aircraft. It shall be the responsibility of the purchaser to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
CURRENT
2017-03-15
Standard
J2302_201703
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
CURRENT
2016-10-30
Standard
AS6171/10
This test method provides the capabilities, limitations, and suggested possible applications of TGA as it pertains to the detection of counterfeit electronic components. Additionally, this document outlines requirements associated with the application of TGA including: equipment requirements, test sample requirements, methodology, control and calibration, data analysis, reporting, and qualification and certification. If AS6171/10 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-09-14
Standard
AS1145C
This specification covers minimum requirements for brake temperature monitoring equipment whenever used on any type and model of civil aircraft. It shall be the responsibility of the purchaser to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
2016-04-13
WIP Standard
J1961
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials. Sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
2016-03-23
WIP Standard
J2230
This SAE Standard specifies operating procedure for the exposure of automotive interior trim materials in an outdoor behind-glass apparatus in which the temperature is controlled in a 24 h cycle. The humidity is controlled during the dark (night) portion of the cycle. Specimen preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
CURRENT
2016-03-11
Standard
J1597_201603
This SAE Recommended Practice is applicable to all liquid-to-gas, liquid-to-liquid, gas-to-gas, and gas-to-liquid heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine durability characteristics of the heat exchanger under pressure cycling.
CURRENT
2016-02-04
Standard
J1542_201602
This SAE Recommended Practice is applicable to all liquid-to-air, liquid-to-liquid, air-to-liquid, and air-to-air heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine durability characteristics of the heat exchanger under thermal cycling.
2015-12-14
WIP Standard
J2412
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.
CURRENT
2015-08-11
Standard
J2412_201508
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components.
2015-05-13
WIP Standard
AIR1657C
Metric (SI and CGS) and English units related to aerospace hydraulics are summarized. Conversion of units is provided as required. Fundamental fluid properties and physical laws governing fluid motion, pressure and other significant aspects are described in SI metric units. Examples of application to typical aerospace hydraulic system components are demonstrated.
CURRENT
2013-11-13
Standard
J951_201311
The purpose of this SAE Information Report is to compare the results of Florida exposure at 45 deg from the horizontal, facing south, with those at deg from the horizontal, facing south, using various types and colors of automotive finishes.
CURRENT
2012-11-19
Standard
J2212_201211
This SAE Recommended Practice specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers.
CURRENT
2012-11-19
Standard
J2019_201211
This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
CURRENT
2011-12-06
Standard
J1310_201112
The scope of this SAE Information Report is to acquaint and inform those concerned with cold weather operation of diesel-powered machines and vehicles with the selection and application of electrically powered starting aids currently available. It deals specifically with the design, function, and application of line voltage electrically powered engine preheaters and battery warmers.
CURRENT
2011-12-06
Standard
J226_201112
This SAE Standard describes electric immersion engine preheaters for use in the coolant jacket of heavy-duty and intermediate size diesel engines. This document gives the dimensional information on the four basic styles of engine preheaters. The tables for each style will list the wattage commonly used. Small engines that typically require less than 600 W of preheat for cold weather starting are not covered by this document. These types of engines generally have very little space available to accommodate an immersion heater of the styles presented in this document. No related ISO standards were found.
CURRENT
2011-11-30
Standard
J1350_201111
This information report covers fuel fired pre-heaters which burn gasoline, diesel, or propane fuels. This type of heater must be used in remote areas where 110/220 V, 60 Hz electric power is not available, and is recommended anywhere an on-board self contained system is required. The guidelines in this report are applicable, but not limited to, fuel burning heater installations on the off-road self-propelled work machines described in SAE J1116.
CURRENT
2011-11-30
Standard
J1024_201111
This standard covers off-road, self-propelled work machines as categorized in SAE J1116. This standard outlines requirements that must be met in order for the heating equipment to perform satisfactorily on construction and industrial machinery.
CURRENT
2011-10-27
Standard
J1422_201110
This SAE Information Report establishes performance requirements for devices used to warm diesel fuel before entering the fuel filter(s).
CURRENT
2011-10-27
Standard
J2079_201110
This SAE Information Report recommends the requirements for the location of ether atomizers.
CURRENT
2011-05-16
Standard
J1961_201105
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials.
CURRENT
2008-07-28
Standard
J2229_200807
This SAE Standard specifies the operating procedures for the exposure of automotive interior trim materials in an outdoor behind glass apparatus in which the temperature is controlled for part of the day. Specimen preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
CURRENT
2008-01-11
Standard
J1960_200801
This test method specifies the operating procedures for a controlled irradiance, water-cooled xenon arc apparatus used for the accelerated exposure of various automotive exterior materials. This standard is limited to the models of xenon arc test apparatus specified in the Section on Apparatus. All other models of xenon arc test apparatus must use SAE J2527 to perform the test conditions specified in SAE J1960. SAE J2527 is the performance standard based on the test parameters of SAE J1960. Use of xenon arc test apparatus to perform SAE J2527 must be agreed upon by contractual parties.
CURRENT
2008-01-11
Standard
J1885_200801
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. This standard is limited to the models of xenon arc test apparatus specified in the Section on Equipment. All other models of xenon arc test apparatus must use SAE J2412 to perform the test conditions specified in SAE J1885. SAE J2412 is the performance standard based on the test parameters of SAE J1885. Use of xenon arc test apparatus to perform SAE J2412 must be agreed upon by contractual parties.
HISTORICAL
2004-05-27
Standard
J2412_200405
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components.
CURRENT
2003-09-25
Standard
AIR1657B
Metric (SI and CGS) and English units related to aerospace hydraulics are summarized. Conversion of units is provided as required. Fundamental fluid properties and physical laws governing fluid motion, pressure and other significant aspects are described in SI metric units. Examples of application to typical aerospace hydraulic system components are demonstrated.
HISTORICAL
2003-02-27
Standard
J2020_200302
This test method specifies the operating conditions for a fluorescent ultraviolet (UV) and condensation apparatus used for the accelerated exposure of various automotive exterior components.
HISTORICAL
2002-03-22
Standard
J1961_200203
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials. Sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
HISTORICAL
1996-11-01
Standard
J1422_199611
This SAE Information Report establishes performance requirements for devices used to warm diesel fuel before entering the fuel filter(s). This document applies to all off-road, self-propelled, diesel-powered work machines described in SAE J1116. This document may be applied to other diesel equipment.
HISTORICAL
1995-06-01
Standard
J226_199506
This SAE Standard describes electric immersion engine preheaters for use in the coolant jacket of heavy-duty and intermediate size diesel engines. This document gives the dimensional information of the four basic styles of engine preheaters. The tables for each style will list the wattage commonly used. Small engines that typically require less than 600 W of preheat for cold weather starter are not covered by this document. These types of engines generally have very little space available to accommodate an immersion heater of the styles presented in this document. The purpose of this document is to establish commonality of engine preheater designs. The user of this document can use these current styles and wattages early on in their designing. This will give the user of this document a good engine preheater design.
Viewing 1 to 30 of 50

Filter

  • Standard
    50