Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 1583
CURRENT
2017-09-19
Standard
J2555_201709
This SAE Standard describes a procedure to be used to evaluate a disturbance known as “idle gear rattle” which can exist in vehicles equipped with manual transmissions and clutches. Other types of noises associated with operation at idle are also briefly described.
CURRENT
2017-09-19
Standard
J2908_201709
This document provides test methods for evaluating the maximum power of electrified vehicle powertrain systems by direct measurement at the drive wheel hubs or axles. Additional tests are included specifically for PHEVs to measure electric-only propulsion power and for HEVs to measure electric power assist and regenerative braking. The testing requires either a chassis or hub dynamometer for all driven wheels. Results are processed to provide fair and consistent comparisons of power capabilities among different designs of electrified powertrains. Tests can also be performed on conventional vehicles if precise comparisons to electrified vehicles are desired.
CURRENT
2017-09-19
Standard
J2710_201709
This SAE Recommended Practice describes test methods for measuring and identifying the lower order natural frequencies of an inflated radial tire with a fixed rim while expending modest effort and employing a minimum of test equipment. The methods apply to any size of radial tire so long as the test equipment is properly scaled to conduct the measurements for the intended test tire. Two types of boundary conditions are considered for the tire: unloaded and loaded against a flat surface. The test involves the performance and measurement of an input vibratory force (excitation) to the tire and the corresponding vibratory output (response). The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTES: The focus of this standard is identification and reporting of the lower order natural frequencies of the tire using a simple test procedure.
CURRENT
2017-09-19
Standard
J2527_201709
This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.
2017-09-18
WIP Standard
J1574/1
The parameters measured according to this SAE Recommended Practice will generally be used in simulating directional control performance in the linear range. (The “linear range” is the steady-state lateral acceleration below which steering wheel angle can generally be considered to be linearly related to lateral acceleration.) But they may be used for certain other simulations (such as primary ride motions), vehicle and suspension characterization and comparison, suspension development and optimization, and processing of road test data. This document is intended to apply to passenger cars, light trucks, and on-highway recreational and commercial vehicles, both non-articulated and articulated. Measurement techniques are intended to apply to these vehicles, with alterations primarily in the scale of facilities required.
2017-09-18
WIP Standard
J1574/2
This SAE Information Report presents the background and rationale for SAE J1574-1. The motor vehicle industry is working toward a more complete understanding of the factors affecting the motions of vehicles on the roadway, by using a variety of techniques that predict responses to road and operator inputs. The capability to predict responses is desirable so that vehicles can be designed for optimum safety and utility. In addition to the force and moment properties of the pneumatic tires, a number of vehicle and suspension parameters affect the response of the vehicle; these include weight, center-of-gravity location, moments of inertia, suspension ride and roll rates, suspension kinematic and compliance properties, and shock absorber characteristics. These parameters must be quantified in order to predict vehicle responses. Measurement of most of these parameters will be limited to determining their values in the linear range for use in directional control simulations.
CURRENT
2017-09-15
Standard
J2938_201709
This SAE Recommended Practice provides the methods of measurements for electrical and photometric characteristics of LED packages. It provides procedures, requirements, and guidelines for the methods of the measurement of luminous flux and color maintenance of LED devices (packages, arrays, and modules) for ground vehicle lighting applications.
2017-09-14
WIP Standard
J356
The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead or scarfed region. Assumption of risks when using this material for single flare applications to be defined by agreement between the producer and tube purchaser. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356.
2017-09-14
WIP Standard
J527
This SAE Standard covers brazed double wall low-carbon steel tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a suitable quality for bending, flaring, beading, forming, and brazing.
CURRENT
2017-09-13
Standard
J1699/2_201709
To define test cases for the OBD-II interface on external test equipment (such as an OBD-II Scan Tool, Inspection/Maintenance Tester, etc.) which can be used to verify compliance with the applicable standards such as SAE J1978 and SAE J1979 for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles and Engines (OBD II).
CURRENT
2017-09-07
Standard
J1498_201709
The heating value or heat of combustion is a measure of the energy available from the fuel. The fraction or percentage of the heat of combustion that is converted to useful work is a measure of the thermal efficiency of an engine. Thus, a knowledge of the heat of combustion of the fuel is basic to the engineering of automotive engines. This SAE Information Report provides information on the standardized procedures for determining the heat of combustion of fuels that may be used for automotive engines.
CURRENT
2017-09-07
Standard
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
CURRENT
2017-09-05
Standard
J2718_201709
This SAE Recommended Practice describes application of two closely related test procedures, which together determine the linear range longitudinal and lateral stiffnesses of a statically loaded non-rotating tire. The procedures apply to any tire so long as the equipment is properly sized to correctly conduct the measurements for the intended test tire. The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE: Herein, road load models are models for predicting forces applied to the vehicle spindles during operation over irregular pavements. Within the context of this document, forces applied to the pavement are not considered.
CURRENT
2017-09-05
Standard
J2704_201709
This SAE Recommended Practice describes a test method for determining the vertical force and deflection properties of a non-rolling tire and the associated contact patch length and width. The method applies to any tire so long as the equipment is properly scaled to conduct the measurements for the intended test tire. The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development.
CURRENT
2017-08-29
Standard
J183_201708
This SAE Standard outlines the engine oil performance categories and classifications developed through the efforts of the Alliance of Automobile Manufacturers (Alliance), American Petroleum Institute (API), the American Society for Testing and Materials (ASTM), the Engine Manufacturers Association (EMA), International Lubricant Specification Advisory Committee (ILSAC), and SAE. The verbal descriptions by API and ASTM, along with prescribed test methods and limits are shown for active categories in Table 1 and obsolete categories in Table A1. Appendix A is a historical documentation of the obsolete categories. For purposes of this document, active categories are defined as those (a) for which the required test equipment and test support materials, including reference engine oils and reference fuels, are readily available, (b) for which ASTM or the test developer monitors precision for all tests, and (c) which are currently available for licensing by API EOLCS.
2017-08-23
WIP Standard
J551/5
This SAE Recommended Practice specifies measurement procedures and performance levels for magnetic and electric field emissions and conducted power mains emissions over the frequency range 150 kHz to 30 MHz, for vehicles incorporating electric propulsion systems, e.g., battery, hybrid, or plug-in hybrid electric vehicles. Conducted emission measurements in this document are applicable only to battery-charging systems which utilize a switching frequency above 9 kHz, are mounted on the vehicle, and whose power is transferred by metallic conductors. Conducted emission requirements apply only during charging of the batteries from AC power lines. Conducted and radiated emissions measurements of battery-charging systems that use an induction power coupling device are not covered by this document. The measurement of electromagnetic disturbances for frequencies from 30 MHz to 1000 MHz is covered in CISPR 12.
2017-08-22
WIP Standard
J2357
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements and design guidelines for electronic devices.
CURRENT
2017-08-18
Standard
J443_201708
This SAE Recommended Practice Specification provides the procedures for using test strips per SAE J442 for peening processes.
CURRENT
2017-08-17
Standard
J2087_201708
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
CURRENT
2017-08-14
Standard
J1204_201708
This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway service on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light truck wheels (inset less than 0.10 m) to this trailer service, use this procedure. For the application of heavier truck wheels (inset 0.10 m (or more)) use SAE J267. Mobile home service is outside the scope of this document. There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel.
CURRENT
2017-08-14
Standard
J1355_201708
This SAE Recommended Practice describes a laboratory test procedure for measuring the thickness of various resilient insulating padding materials that are used in the automotive industry. Such padding materials may include synthetic or non-synthetic materials, fibrous or cellular materials, high loft or compressed materials, single layer homogeneous or multilayer products, low and high surface density products. Some of these samples may be deformable and elastic, high loft thermal and acoustical fibrous materials, as well. The test method described herein has been developed to establish a means of a uniform procedure for measuring the thickness of different types of samples not only for application to all ground vehicles, but also may be applicable to other situations or conditions. The test method is designed to measure the thickness of flat samples and not formed parts. This test method does not purport to address all of the safety concerns, if any, associated with its use.
CURRENT
2017-08-11
Standard
J2846_201708
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated.
CURRENT
2017-08-09
Standard
J442_201708
This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
CURRENT
2017-07-26
Standard
J2452_201707
This SAE Recommended Practice is applicable to pneumatic Passenger Car "P" Type, Light Truck Metric, and Light Truck High Flotation tires, or similar tires approved by bodies other than Tire & Rim Association. The methodology is applicable within normal operating ranges of vertical load and inflation pressure, and for velocities between 115 km/h and 15 km/h (71 mph and 9 mph) during a relatively short duration event such as a coastdown. This procedure is applicable only to operation in the free-rolling mode at zero slip and camber angle for ambient temperatures between 20 °C and 28 °C (68 °F and 82 °F) and for surfaces with diameters of 1.2 m (48 in) diameter or greater. Details regarding the equipment, tires, and test methods used specifically for validation of this document are included in Appendix A.
CURRENT
2017-07-24
Standard
J2625_201707
This procedure is applicable to squeal type noise occurrences for passenger car and light truck type vehicles that are used under conventional operating conditions. For the purposes of this test procedure, squeal is defined as occurring between 900 and 18 000 Hz.
CURRENT
2017-07-21
Standard
J1699/3_201707
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/E Diagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics – Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
2017-07-18
WIP Standard
J2986
This Recommended Practice provides a common method to measure wear of friction materials (brake pad assemblies and brake shoes) and their mating part (brake rotor or brake drum). These wear measurements apply to brakes fitted on passenger cars and light trucks up to 4,540 kg of Gross Vehicle Weight Rating or vehicles category M1 on the European Community.
2017-07-14
WIP Standard
J814

This SAE Information Report is a source of information concerning the basic properties of engine coolants which are satisfactory for use in internal combustion engines. Engine coolant concentrate (antifreeze) must provide adequate corrosion protection, lower the freezing point, and raise the boiling point of the engine coolant. For additional information on engine coolants see ASTM D 3306 and ASTM D 4985.

The values presented describe desirable basic properties. The results from laboratory tests are not conclusive, and it should be recognized that the final selection of satisfactory coolants can be proven only after a series of performance tests in vehicles.

The document describes in general the necessary maintenance procedures for all engine coolants to insure proper performance as well as special requirements for coolants for heavy-duty engines.

This document does not cover maintenance of engine cooling system component parts.

CURRENT
2017-07-13
Standard
J2749_201707
This recommended practice is a guideline for generating high strain rate tensile properties under defined conditions of unreinforced and reinforced plastics used in the automotive industry. Several types of test specimens are identified to suit different types of materials and test rates. This document is intended for strain rates between 10-3/s and 103/s. Test procedures for rates of 10-2/s and below; i.e., quasi-static conditions, are described in ASTM D 638 and ISO 527-1. The procedures in this document include quasi-static testing in order to provide a common test rate for both quasi-static and dynamic test programs. The general procedures listed in ASTM D 638 and ISO 527-1 should be followed when appropriate. The main purpose of this document is to determine the relative effects of increasing strain rate on the measured material properties. Data generated from these tests are comparative in nature.
Viewing 1 to 30 of 1583