Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 7095
CURRENT
2016-12-12
Standard
ARP5448/7A
This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a. Destructive Inspection - Cut and measure (not applicable to molded liners) b. Nondestructive Inspection - Radial play (gauge) measurement
2016-11-30
WIP Standard
J361
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
CURRENT
2016-11-29
Standard
AMS2636A
This specification covers procedures for ultrasonic immersion inspection of premium grade wrought titanium and titanium alloy forgings. Premium grade is a term used to describe titanium alloys used for critical rotating components in turbine engines. For details, see SAE AMS2380, the specification that covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products.
CURRENT
2016-11-29
Standard
AIR1873A
This Aerospace Information Report (AIR) describes a Limited Engine Monitoring System that can be used by the flight crew or the maintenance staff, or both, to monitor the health of gas turbine engines in aircraft. This AIR considers monitoring of gas path performance and mechanical parameters, and systems such as low cycle fatigue counters and engine history recorders. It also considers typical measurement system accuracies and their impact. This AIR is intended as a technical guide. It is not intended to be used as a legal document or standard. AIR 1873 supplements ARP 1587, Aircraft Gas Turbine Engine Monitoring System Guide.
2016-11-28
WIP Standard
ARP6914
The scope of these standards will relate to single-axis moment scales only. Topics covered include dimensional characteristics of single-axis moment scale interfaces, general tooling requirements, scale and tooling accuracy, and display instrument accuracy requirements. Additionally, general guidelines for qualification of equipment and tooling are included, as are general requirements for single-axis blade distribution software.
2016-11-23
WIP Standard
AS407E
To specify minimum requirements for Fuel Flowmeters for use primarily in reciprocating engine powered civil transport aircraft, the operation of which may subject the instruments to the environmental conditions specified in Section 3.3. This Aeronautical Standard covers two basic types of instruments, or combinations thereof, intended for use in indicating fuel consumption of aircraft engines as follows: TYPE I - Measure rate of flow of fuel used. TYPE II - Totalize amount of fuel consumed or remaining.
CURRENT
2016-11-18
Standard
J2358_201611
This SAE Standard defines the safety and performance requirements for Low Speed Vehicles (“LSV”). The safety specifications in this document apply to any powered vehicle with a minimum of 4-wheels, a maximum level ground speed of more than 32 km/h (20 mph) but not more than 40 km/h (25 mph),), and a maximum gross vehicle weight of 1361 kg (3000 pounds), that is intended for operating on designated roadways where permitted by law.
CURRENT
2016-11-18
Standard
J361_201611
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
2016-11-16
WIP Standard
J2707
This SAE Recommended Practice specifies a dynamometer test procedure to be used for the measurement of automotive service brake linings and disc brake pads wear. Special motor vehicles and motorcycles are excluded from the application. Trailers with nominal Gross Combination Weight Rating exceeding 40 tons are also excluded from this Recommended Practice.
CURRENT
2016-11-15
Standard
J1281_201611
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.
2016-11-14
WIP Standard
ARP5305A
This SAE Aerospace Recommended Practice (ARP) is written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in constructing new or adding to existing engine test cell facilities.
CURRENT
2016-11-12
Standard
ARP5448/1A
This test method outlines the recommended procedure for performing radial limit load and ultimate load tests on low speed airframe and high speed helicopter rotor head bearings.
CURRENT
2016-11-12
Standard
ARP5448/5A
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
CURRENT
2016-11-10
Standard
J2318_201611
This procedure provides test performance requirements for service, spring applied parking, and double diaphragm combination air brake actuators with respect to durability, function, and environmental performance when tested in accordance to SAE J1469.
2016-11-09
WIP Standard
AIR6911
The goal of this new Aerospace Information Report is to supplement the content of AS6327™ and provide a reference document for the new Aerospace Standard. This new Aerospace Information Report will serve as a practical resource that offers guidance to the machine operator and Process Engineer for isolating the source(s) of non-repeatability in measured unbalance data. The content will include: • Machine Capability to achieve the specified unbalance tolerances and repeat within those tolerances • Tooling Capability to repeat within the specified unbalance tolerances • Rotor characteristics that may preclude repeating within the required unbalance tolerances.
CURRENT
2016-11-08
Standard
J964_201611
This SAE Recommended Practice describes methods for determining total and specular reflectance for mirrors with flat and curved surfaces and a method for determining diffuse reflectance and haze for mirrors with flat surfaces.
2016-11-07
WIP Standard
AIR7483
This AIR provides information about polymeric materials (Super Absorbent Polymers - SAP) used in Filter Monitors for free water removal, the possibility of migration of such material in to aircraft fuel systems and the potential impact on fuel system operation along with light incidents traceable to the migration of SAP in to the aircraft fuel system are enumerated. The measures taken to minimize SAP migration are also discussed.
2016-11-03
WIP Standard
AIR6805
This document will outline existing best practices in the instrumentation of landing gears for in-service operation (including flight test, operational loads monitoring, etc.).
2016-11-03
WIP Standard
AS39029/91B
No scope available.
2016-11-03
WIP Standard
AS39029/90B
No scope available.
2016-10-31
WIP Standard
ARP7998
This is a recommended practice for an interface to supplier simulations that utilize traditional interprocess communication (IPC) methods of shared memory and semaphore communications. These IPC methods are fairly standard practice in the computer science world, that allow for communication by separate processes running on a computer without any common runtime requirements of each process being run. So 32bit applications can talk with 64 bit applications as well as any other compiler or runtime dependency being needed by the calling program to interface with the called system. This also allows the calling program and the called program to be run on separate CPUs to allow parallel execution of the called program as well as multiple instances of the called program to execute all on separate processors.
CURRENT
2016-10-30
Standard
AS6171/10
This test method provides the capabilities, limitations, and suggested possible applications of TGA as it pertains to the detection of counterfeit electronic components. Additionally, this document outlines requirements associated with the application of TGA including: equipment requirements, test sample requirements, methodology, control and calibration, data analysis, reporting, and qualification and certification. If AS6171/10 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/9
This document defines capabilities and limitations of FTIR spectroscopy as it pertains to counterfeit electronic component detection and suggests possible applications to these ends. Additionally, this document outlines requirements associated with the application of FTIR spectroscopy including: operator training, sample preparation, various sampling techniques, data interpretation, computerized spectral matching including pass/fail criteria, equipment maintenance, and reporting of data. The discussion is primarily aimed at analyses performed in the mid-infrared (IR) from 400 to 4000 wavenumbers; however, many of the concepts are applicable to the near and far IR. If AS6171/9 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/8
To define capabilities and limitations of Raman spectroscopy as it pertains to counterfeit detection of EEE parts and suggest possible applications to these ends. Additionally, this document outlines requirements associated with the application of Raman spectroscopy including: Operator training; Sample preparation; Data interpretation; Computerized spectral matching including pass/fail criteria; Equipment maintenance and; Reporting of data. If AS6171/8 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/6
Through the use of ultra-high frequency ultrasound, typically above 10 MHz, Acoustic Microscopy (AM) non-destructively finds and characterizes physical features and latent defects (visualization of interior features in a layer by layer process) - such as material continuity and discontinuities, sub-surface flaws, cracks, voids, delaminations and porosity. AM observed features and defects can be indicators that the components were improperly handled, stored, altered or previously used. If AS6171/6 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/3
XRF technique for counterfeit detection is applicable to electrical, electronic and electromechanical (EEE) parts as listed in AS6171 General Requirements. In general, the detection technique is meant for use on piece parts prior to assembly on a circuit board or on the parts that are removed from a circuit board. The applicability spans a large swath of active, passive and electromechanical parts. If AS6171/3 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/11
This method outlines the requirements, capabilities, and limitations associated with the application of Design Recovery for the detection of counterfeit electronic parts including: Operator training; Sample preparation; Imaging techniques; Data interpretation; Design/functional matching; Equipment maintenance and; Reporting of data. The method is primarily aimed at analyses performed by circuit delayering and imaging with a scanning electron microscope or optical microscope; however, many of the concepts are applicable to other microscope and probing techniques to recover design data. The method is not intended for the purpose of manufacturing copies of a device, but rather to compare images or recover the design for determination of authenticity. If AS6171/11 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
CURRENT
2016-10-30
Standard
AS6171/7
The scope of this document is to: Specify techniques to detect SC parts using electrical testing. Provide various levels of electrical testing that can be used by the User to define test plans for detecting SC parts. Provide minimum requirements for testing laboratories so that User/Requester can determine which test houses have the necessary capabilities. (For example: technical knowledge, equipment, procedures and protocols for performing electrical testing for verification analysis.) Note: User/Requester is defined in AS6171 General Requirements Specify Burn-In and environmental tests. The environmental tests include Temperature Cycling for Active Devices and Thermal Shock for Passive Devices. Seal Tests are described and recommended for hermetic devices. The following terminology is used throughout this document: Shall = is mandatory; Should = is recommended; and Will = is planned (is considered to be part of a standard process).
CURRENT
2016-10-30
Standard
AS6171/4
This method standardizes inspection, test procedures and minimum training and certification requirements to detect Suspect/Counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) components or parts utilizing Delid/Decapsulation Physical Analysis. The methods described in this document are employed to either delid or remove the cover from a hermetically sealed package or to remove the encapsulation or coating of an EEE part, in order to examine the internal structure and to determine if the part is suspect counterfeit. Information obtained from this inspection and analysis may be used to: prevent inclusion of counterfeit parts in the assembly identify defective parts aid in disposition of parts that exhibit anomalies This test method should not be confused with Destructive Physical Analysis as defined in MIL-STD-1580. MIL-STD-1580 describes destructive physical analysis procedures for inspection and interpretation of quality issues.
CURRENT
2016-10-30
Standard
AS6171
This SAE Aerospace Standard (AS) standardizes inspection and test procedures, workmanship criteria, and minimum training and certification requirements to detect Suspect/Counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) parts. The requirements of this document apply once a decision is made to use parts with unknown chain of custody that do not have pedigree back to the original component manufacturer, or have been acquired from a broker or independent distributor, or when there are other known risk elements that result in the User/Requester to have concerns about potential SC EEE parts. The tests specified by this standard may also detect occurrences of malicious tampering, although the current version of this standard is not designed specifically for this purpose. This standard ensures consistency across the supply chain for test techniques and requirements based on assessed risk associated with the application, component, supplier, and other relevant risk factors.
Viewing 121 to 150 of 7095