Criteria

Text:
Display:

Results

Viewing 1 to 30 of 1483
2017-03-28
Technical Paper
2017-01-0428
Tianqi Lv, Yan Wang, Xingxing Feng, Yunqing Zhang
Abstract Steering returnability is an important index for evaluating vehicle handling performance. A systematic method is presented in this paper to reduce the high yaw rate residue and the steering response time for a light duty truck in the steering return test. The vehicle multibody model is established in ADAMS, which takes into consideration of the frictional loss torque and hydraulically assisted steering property in the steering mechanism, since the friction, which exists in steering column, spherical joint, steering universal joint, and steering gear, plays an important role in vehicle returnability performance. The accuracy of the vehicle model is validated by road test and the key parameters are determined by executing the sensitivity analysis, which shows the effect of each design parameter upon returnability performance.
2017-03-28
Technical Paper
2017-01-0439
Joydeep Chatterjee, Yuva Kishore Vaddi, Chetan Prakash Jain
Abstract In urban driving conditions, the steering vibration plays a major role for a customer, spending a significant amount of time behind the steering wheel. Considering the urban drive at Indian roads, 1000~1600rpm band becomes primary area of concern. In this paper, study has been conducted to define the target areas as well as its achievement in reference to given driving pattern on a front wheel powered passenger car for steering vibration. During the concept stage of vehicle development, a target characteristic of steering wheel vibration was defined based on the competitor model benchmarking and prior development experience. A correlated CAE model was prepared to evaluate the modification prior to prototype building and verification. Vibration level in all 3 degrees of freedom at the steering wheel location was measured in the initial vehicle prototypes and target areas of improvement are identified.
2017-03-28
Technical Paper
2017-01-0416
Vishal Barde, Baskar Anthonysamy, Ganeshan Reddy, Senthil S, Visweswara lenka, Gurdeep Singh Pahwa
Abstract New trend in steering system such as EPS is coming up, but still hydraulic power steering system is more prevalent in today’s vehicles. Power steering pump is a vital component of hydraulic power steering system. Failure of steering pump can lead to loss of power assistance. Prediction of hub load on pump shaft is an important design input for pump manufacturer. Higher hub loads than the actual designed load of pump bearing may lead to seizure of pump. Pump manufacturer has safe limits for hub load. Simulations can assist for optimization of belt layout and placement of accessories to reduce the hub load. Lower hub load can have direct effect on improvement of pump durability. This paper deals with dynamic simulation of belt drive system in MSC.ADAMS as well as vehicle level measurement of hub load on power steering pump.
2017-03-28
Technical Paper
2017-01-1371
Hao Pan, Xuexun Guo, Xiaofei Pei, Xingzhi Dong
Abstract Brake pedal feel plays an important role in the driver's comprehensive subjective feeling when braking, which directly affects the active safety and riding comfort of passenger car. A systematical mathematical model of the vehicle brake system is built in according with the structure and system characteristics of hydraulic servo brake system. A complete hydraulic servo brake system simulation model composed of brake pedal, vacuum booster, brake master cylinder, brake pipe, brake wheel cylinders, brake calipers is established in AMESim. The effects of rubber reaction plate stiffness, rubber valve opening, brake master cylinder piston, brake caliper, brake pipe deformation and friction liner deformation on brake pedal feel are considered in this model. The accuracy of this model is verified by real road vehicle tests under static and dynamic two different conditions.
2017-03-28
Technical Paper
2017-01-1399
Bin Wu, Xichan Zhu, Jianping Shen, Xuejun Cang, Lin li
Abstract A driver steering model for emergency lane change based on the China naturalistic driving data is proposed in this paper. The steering characteristic of three phases is analyzed. Using the steering primitive fitting by Gaussian function, the steering behaviors in collision avoidance and lateral movement phases can be described, and the stabilization steering principle of yaw rate null is found. Based on the steering characteristic, the near and far aim point used in steering phases is analyzed. Using the near and far aim point correction model, a driver steering model for emergency lane change is established. The research results show that the driver emergency steering model proposed in this paper performs well when explaining realistic steering behavior, and this model can be used in developing the ADAS system.
2017-03-28
Technical Paper
2017-01-1555
Mirosław Jan Gidlewski, Krystof JANKOWSKI, Andrzej MUSZYŃSKI, Dariusz ŻARDECKI
Abstract Lane change automation appears to be a fundamental problem of vehicle automated control, especially when the vehicle is driven at high speed. Selected relevant parts of the recent research project are reported in this paper, including literature review, the developed models and control systems, as well as crucial simulation results. In the project, two original models describing the dynamics of the controlled motion of the vehicle were used, verified during the road tests and in the laboratory environment. The first model - fully developed (multi-body, 3D, nonlinear) - was used in simulations as a virtual plant to be controlled. The second model - a simplified reference model of the lateral dynamics of the vehicle (single-body, 2D, linearized) - formed the basis for theoretical analysis, including the synthesis of the algorithm for automatic control. That algorithm was based on the optimal control theory.
2017-03-28
Technical Paper
2017-01-1591
Haotian Cao, Xiaolin Song, Zhi Huang
Abstract Generally speaking, lateral steering control method which ensures a good performance in tracking quality and handle quality simultaneously for autonomous vehicle is a changeling task. In order to keep the vehicle to stay safe when facing with severe situations such as an emergency lane change, a switched MPC lateral steering controller, which is on the basis of the stability feature of the vehicle, is presented in this paper. First, a MPC steering controller based on the 3DOF nonlinear vehicle model is derived, a comparative study of different vehicle models for MPC prediction are made. It proves that the presented MPC controller based on 3DOF nonlinear vehicle model possesses an advantage of balancing the conflicts between the tracking quality and handling quality of the vehicle.
2017-03-28
Technical Paper
2017-01-1585
Renxie Zhang, Lu Xiong, Zhuoping Yu, Wei Liu
Abstract A dynamic controller is designed for unmanned skid-steering vehicle. The vehicle speed is controlled through driving torque of engine to achieve the desired vehicle speed and the steering is controlled through hydraulic braking on each side of the vehicle to achieve the desired yaw rate. Contrary to the common approaches by considering non-holonomic constraints, tire slip and saturation of actuators torque influencing the driving and braking are considered, based on the analysis of vehicle dynamic model and nonlinear tire model. Hence, with conditional integrators, the dynamic controller overcoming integral saturation is designed to ensure the accurate tracking for desired signals under influence of tire forces and constraint of actuators. In addition, the exponential kind filter is utilized to enhance the ability of smoothing noise of wheel speed. To perform small radius cornering maneuvers, a dynamic control strategy for steering when vehicle speed is zero is also designed.
2017-03-28
Technical Paper
2017-01-1579
Liang-kuang Chen, Chien-An Chen
Abstract The development of an integrated controller for a 4WS/4WD electric bus is investigated. The front wheel steering angle is assumed to be controlled by the human driver. The vehicle is controlled by the rear wheel steering and the yaw moment that can be generated by the differential torque/brake control on each wheel. The high speed cornering is used as the testing scenario to validate the designed controller. Due to the highly nonlinear and the multiple-input and multiple-output nature, the control design is separated into different stages using the hierarchical layer control concept. The longitudinal speed is controlled using a PI controller together with a rule-based speed modification. The other two control inputs, namely the rear wheel steering and the DYC moment, are then designed using the state-dependent Riccati equation method. The designed controllers are evaluated using computer simulations first, and the simulations showed promising results.
2017-03-28
Technical Paper
2017-01-1567
Jaepoong Lee, Sehyun Chang, Kwangil Kim, Bongchoon Jang, Dongpil Lee, Byungrim Lee, Kyongsu Yi
Abstract This paper proposes a reference steering wheel torque map and a torque tracking algorithm via steer-by-wire to achieve the targeted steering feel. The reference steering wheel torque map is designed using the measurement data of rack force and steering characteristic of a target performance of the vehicle at transition steering test. Since the target performance of the vehicle is only tested in nominal road condition, various road conditions such as disturbances and tire-road friction are not considered. Hence, the measurement data of the rack force that reflects the road conditions in the reference steering wheel torque map have been used. The rack force is the net force which consists of tire aligning moment, road friction force and normal force on the tire kingpin axis. A motor and a magnetorheological damper are used as actuators to generate the desired steering feel using the torque tracking algorithm.
2017-03-28
Technical Paper
2017-01-1571
Kevin McLaughlin, Jonah Shapiro, HyungJu Kwon
Abstract An approach to electric steering control and tuning is developed using vehicle dynamics and quantitative steering objectives. The steering objective chosen is the torque vs. lateral acceleration target for the driver termed the “steering gain”. Two parameters are derived using vehicle dynamics that substantially determine driver feel: the vehicle’s “manual gain” (total steering torque divided by lateral acceleration) and the vehicle’s lateral acceleration gain (lateral acceleration divided by steering angle). Lateral acceleration gain is a well-known quantity in the literature but “manual gain” is a nonstandard point of view for steering control systems. The total gain inside the controller is the loop gain; generally, the higher the loop gain, the better the controller rejects unwanted effects such as friction. For a typical torque-input electric steering topology, it is shown that the relationship between loop gain and steering gain is unique.
2017-03-28
Technical Paper
2017-01-1494
Weinan Tao, Bingzhao Gao, Hongqing Chu, Mengjian Tian, Hong Chen
Abstract The steer-by-wire system has been widely studied due to many advantages such as good controllability. In the system, the steering column is cancelled and the driver can't feel the feedback torque (also called steering feeling) coming from the ground. Therefore a steering feeling feedback system is needed. In this paper, we propose a simple method to calculate desired feedback torque based on a nonlinear 2DOF vehicle model. The vehicle model contains the nonlinearity of tire. So that the proposed method is also appropriate for big acceleration conditions. Besides that, the properties of steering system such as friction and stiffness are also taken into consideration. As for conventional steering system, driver can only feel part of the feedback torque due to the power assist system. In order to provide steering feeling similar to conventional steering system, a weighting function is proposed to compensate the influence of power assist system.
2017-03-28
Journal Article
2017-01-1489
Duanxiang Zhang, Bo Lin, Ahmet Kirli, Chinedum Okwudire
Abstract Electric Power Assisted Steering (EPAS) is widely adopted in modern vehicles to reduce steering effort. It is probable that some EPAS systems will experience a shutdown due to reliability issues stemming from electrical and/or electronic components. In the event of EPAS failure, power assist becomes unavailable and the steering system reverts to a fully manual state, leading to excessive steering torque demands from the driver to maneuver the vehicle at lower speeds, i.e., under 30 mph. This situation has resulted in dozens of reported crashes and several OEM safety recalls in the past few years. Inspired by recent work which utilizes independent driving torque of in-wheel-motor vehicles to reduce steering torque, this paper proposes the use of Differential Braking Assisted Steering (DBAS) to alleviate steep increases in steering torque upon EPAS failure. DBAS requires software upgrades with minimal hardware modification to EPAS, which is preferable for a backup system.
2017-03-28
Technical Paper
2017-01-1478
Srinivas Kurna, Sajal Jain, Palish Raja, Laxman Vishwakarma
Abstract In an automobile, main function of the steering system is to allow the driver to guide the vehicle on a desired course. Steering system consists of various components & linkages. Using these linkages, the torque from steering wheel is transferred to tyre which results in turning of the vehicle. Over the life of vehicle, these steering components are subjected to various loading conditions. As steering components are safety critical parts in the vehicle, therefore they should not fail while running because it will cause vehicle breakdown. In commercial vehicle segment, vehicle breakdown means delay in freight delivery which results in huge loss to costumer. Therefore, while designing steering components one should consider all the possible loadings condition those are possible. But, it can’t be done through theoretical calculation. Therefore, physical tests have to be carried out to validate design of steering system, which is very costly & time-consuming process.
2017-03-28
Technical Paper
2017-01-0066
Shogo Nakao, Akihiko Hyodo, Masaki Itabashi, Tomio Sakashita, Shingo Obara, Tetsuya Uno, Yasuo Sugure, Yoshinobu Fukano, Mitsuo Sasaki, Yoshihiro Miyazaki
This paper presents the “Virtual Failure Mode and Effects Analysis (vFMEA)” system, which is a high-fidelity electrical-failure-simulation platform, and applies it to the software verification of an electric power steering (EPS) system. The vFMEA system enables engineers to dynamically inject a drift fault into a circuit model of the electronic control unit (ECU) of an EPS system, to analyze system-level failure effects, and to verify software-implemented safety mechanisms, which consequently reduces both cost and time of development. The vFMEA system can verify test cases that cannot be verified using an actual ECU and can improve test coverage as well. It consists of a cycle-accurate microcontroller model with mass-production software implemented in binary format, analog and digital circuit models, mechanical models, and a state-triggered fault-injection mechanism.
2017-03-28
Journal Article
2017-01-1485
Mikihiro Hiramine, Yoshitaka Hayashi, Takashi Suzuki
Abstract The electric power steering (EPS) is increasing its number since there are many advantages compared to hydraulic power steering. The EPS saves fuel and eliminates hydraulic fluid. Also, it is more suitable to the cooperation control with the other vehicle components. The EPS is now expanding to the heavier vehicle with the advance in the power electronics. In order to meet customer's needs, such as down-sizing, lower failure rate and lower price, we have developed the new motor control unit (MCU) for the EPS. The motor and the electric control unit (ECU) were integrated for the better installation. We adopted new technologies of redundant 2-drive design for more safe EPS. “2-drive Motor Control technology” which consists of dual winding, two torque sensors and two inverter drive units. In our developed MCU, even if there is a failure in one of the drive unit, the assistance of the EPS can be maintained with the other drive unit.
2017-03-28
Technical Paper
2017-01-1481
Kyung-bok Lee, Sanghyuk Lee, Namyoung Kim, Bong Soo Kim, Tae soo Chi, Do young Kim
Abstract Conventional EPS (Electric Power Steering) systems are operated by one type of steering tuning map set by steering test drivers before being released to customers. That is, the steering efforts can't change in many different driving conditions such as road conditions (low mu, high mu and unpaved roads) or some specific driving conditions (sudden stopping, entering into EPS failure modes and full accelerating). Those conditions can't give drivers consistent steering efforts. This paper approached the new concept technology detecting those conditions by using vehicle and EPS sensors such as tire wheel speeds, vehicle speed, steering angle, steering torque, steering speed and so on. After detecting those conditions and judging what the best steering efforts for safe vehicle driving are, EPS systems automatically can be changed with the steering friction level and selection of steering optimized mapping on several conditions.
2017-03-28
Technical Paper
2017-01-1636
Lukas Preusser
Abstract Along with the development and marketability of vehicles without an internal combustion engine, electrically heated surfaces within these vehicles are getting more and more important. They tend to have a quicker response while using less energy than a conventional electric heater fan, providing a comfortable temperature feel within the cabin. Due to the big area of heated surface it is important to spread the heating power in a way that different heat conduction effects to underlying materials are considered. In case an accurate sensor feedback of the targeted homogeneous surface temperature cannot be guaranteed, a thermal energy model of the heated system can help to set and maintain a comfortable surface temperature. For a heated steering wheel development project, different models have been created to meet that aim using mechanistic approaches starting with a predominantly first-order dynamics model and ending with a distributed parameter multi-feedback system.
2017-03-28
Technical Paper
2017-01-1176
Hafiz S. Khafagy
Abstract Auto stop-start (Engine stop-start, ESS) has become a widely used feature to reduce fuel consumption and CO2 emissions particularly in congested cities. Typically, vehicles equipped with such systems include two DC power sources that are coupled in parallel: a primary and a secondary power source. The primary power source supplies energy to the starter to crank the engine, while the secondary power source supplies energy to the rest of the vehicle electric loads. During an auto-stop event, a controllable switch decouples the two power sources. Moreover, operating current, voltage and the State of Charge (SOC) are monitored to ensure enough energy for the next auto-start event. When any of these operating parameters are below the threshold values, the controllable switch opens to isolate the two batteries and then the engine is automatically started.
2017-03-28
Journal Article
2017-01-1482
Jens Dornhege, Simon Nolden, Martin Mayer
Abstract The layout of a vehicle steering system has to resolve a compromise. While it is important for lateral vehicle control to feel steering torque feedback of lateral tire to ground interaction, disturbing forces shall not be present in the feedback steering torque. These disturbing forces result from road irregularities, wheel rotor imbalance, suspension asymmetry caused by production tolerances, wear or impacts, and additional vehicle internal forces, e.g. the steered wheels also driven by the engine or braked. In general these disturbances are reduced by an optimization of the suspension geometry to decrease the impact of the unintended forces on the steering system. The remaining disturbance is controlled to an acceptable level via force feedback sensitivity calibration of the steering system, what in return influences the intended driver sensitivity to feel lateral tire forces.
2017-03-28
Journal Article
2017-01-1493
Dexin Wang, Yiqin Mao, Timothy Drotar, Frank Esser, Hessel van Dijk, Michel Paas
Abstract Subjective steering feel tuning and objective verification tests are conducted on vehicle prototypes that are a subset of the total number of buildable combinations of body style, drivetrain and tires. Limited development time, high prototype vehicle cost, and hence limited number of available prototypes are factors that affect the ability to tune and verify all the possible configurations. A new model-based process and a toolset have been developed to enhance the existing steering development process such that steering tuning efficiency and performance robustness can be improved. The innovative method utilizes the existing vehicle dynamics simulation and/or physical test data in conjunction with steering system control models, and provides users with simple interfaces which can be used by either CAE or development engineers to perform virtual tuning of the vehicle steering feel to meet performance targets.
2017-03-28
Journal Article
2017-01-1569
Amro Elhefnawy, Alhossein sharaf, Hossam Ragheb, Shawky Hegazy
Abstract This paper presents an advanced control system, which integrates three fuzzy logic controllers namely; Direct Yaw-moment Control (DYC), Active Roll-moment Control (ARC) and Active Front Steering (AFS) to enhance vehicle cornering and overturning stability. Based on a well-developed and validated fourteen degree of freedom (DOF) full vehicle model with non-linear tire characteristics, a reference 3-DOF yaw-roll plane vehicle model is introduced to control yaw rate, sideslip angle, and roll angle of the vehicle body. The control actions of both direct yaw and active roll moments are performed by generating differential braking moments across the front wheels, while the control action of the active steering is performed by modifying the steering wheel angle. Different standard cornering tests are conducted in MATLAB / Simulink environment such as J-turn, fishhook and lane change maneuvers.
2017-03-28
Journal Article
2017-01-1584
Peng Hang, Xinbo Chen, Fengmei Luo, Shude Fang
Abstract Compared with the traditional front-wheel- steering (FWS) vehicles, four-wheel-independent-steering (4WIS) vehicles have better handing stability and path-tracking performance. In view of this, a novel 4WIS electric vehicle (EV) with steer-by-wire (SBW) system is proposed in this paper. As to the 4WIS EV, a linear quadratic regulator (LQR) optimal controller is designed to make the vehicle track the target path based on the linear dynamic model. Taking the effect of uncertainties in vehicle parameters into consideration, a robust controller utilizing μ synthesis approach is designed and the controller order reduction is implemented based on Hankel-Norm approximation. In order to evaluate the performance of the designed controllers, numerical simulations of two maneuvers are carried out using the nonlinear vehicle model with 9 degrees of freedom (DOF) in MATLAB/Simulink.
2017-01-10
Technical Paper
2017-26-0220
Ashutosh Dubey, Palish Raja, Nitin Chopra, Ashok Patidar, Manu Kaushik
Abstract With the increase in the sensitivity of power steering system in the competitive environment, it becomes essential to provide a trouble free steering system to the customer. Usually major concerns faced in the performance of steering system are related to noise like vane pump whining noise and steering gearbox erratic rubbing noise. Even though selected steering pump and reservoir are quite compatible to the steering gearbox. With the series of Computational Fluid Dynamics (CFD) simulations and field tests, it is found that the cavitation phenomena in steering oil routing lines is responsible for the steering turning noise. In this paper, a developed systematic approach for problem detection to implementation of design solution is discussed.
2017-01-10
Technical Paper
2017-26-0259
Sandeep V. Sawangikar, Jeevan N. Patil, Sivakumar Palanivelu, Arun Kumar K
Abstract Steering system deliver a precise directional control to the vehicle chassis and ensure the safe driving at all maneuvers. Hydraulic power assisted system (HPAS) helps drivers to steer by boosting steering assistance of the steering wheel while retaining the road feel. HPAS performance is associated with the design characteristics of rotary valve, steering, suspension, kinematics, brake, tire, vehicle speed and load transfer. Thus a detailed power steering system model is absolutely necessary to evaluate and optimize the performance characteristics. However, many components of HPAS system are proprietary in nature so it is very challenging to get component characteristic of each sub-system for the complete power steering system model. Hence, it is very important to establish a technique to extract all such influencing characteristics with available test facility.
2017-01-10
Technical Paper
2017-26-0080
P. Ramani Ranjan Senapati, Soumyo Das, Prashantkumar B. Vora
Abstract The development of intelligent driver assistance mechanism ensures safety and comfort of passengers, the intelligent braking and maneuvering mechanism is proposed by transforming the anti-lock braking technology for a four wheeled vehicle. This paper presents an active safety mechanism which incorporates both steering and braking assistance system in a maneuvering vehicle. The algorithm of collision avoidance mechanism is featured and interfaced in an intelligent vehicle with short range radar to assist driving system of host vehicle based on predicted motion of sensed obstacles. The developed system will be activated for obstacles in front of the host vehicle within critical risk level. The intelligent braking mechanism plays a pivotal role at the time of emergency situation depending on the predicted collision time and relative velocity between host and target, it also provides assistance to avoid panic situation for driver.
2017-01-10
Technical Paper
2017-26-0315
Jyoti Kale, Satish Kumar, Pravin Lavangare, Anand Subramaniam
Abstract The Steering system is one of the most safety critical systems in an automobile. With time the durability, reliability and the fine-tuning of the parameters involved in this subsystem have increased along with the competitiveness of the market. In a competitive market, accelerated testing is the key to shorter development cycles. It is observed that the majority of component manufacturers have a preference on vehicle level testing to achieve their development goals. The vehicle level trials are time consuming and lack the control and repeat-ability of a laboratory environment. This paper describes the development of a steering test rig designed to simulate the disturbances experienced on road within a controlled laboratory environment. The five axis steering rig would allow simulation of individual road wheel displacement along with steering wheel angle input and lateral steering rack displacements. The rig also is designed to be adaptable to a range of vehicle categories.
2017-01-10
Technical Paper
2017-26-0293
Sachin lambate, Kedar Shrikant Joshi, Gautam Diwan, Pratap Daphal
Abstract Steering column and steering wheel are critical safety components in vehicle interior environment. Steering system needs to be designed to absorb occupant impact energy in the event of crash thereby reducing the risk of injury to the occupant. This is more critical for non-airbag vehicle versions. To evaluate the steering system performance, Body block impact test is defined in IS11939 standard [1]. Nowadays for product development, CAE is being extensively used to reduce development cycle time and minimize number of prototypes required for physical validation. In order to design the steering system to meet the Body Block performance requirements, a detailed FE model of Body Block impactor is required. The static stiffness and moment of inertia of body block are defined in SAE J244a [2]. The reference data available in SAE J244a is not sufficient to develop a Body Block model that would represent the physical impactor.
2017-01-10
Technical Paper
2017-26-0339
Jagankumar Mari, Egalaivan Srinivasan
Abstract In heavy commercial vehicle segment in India, driver comfort and feel was largely ignored. Fierce competition in the recent years and buyer’s market trend is compelling the designers of heavy truck to focus more on the finer aspects of attribute refinements. Steering is one driver-Vehicle interface which the driver is engaged throughout. Comfort and feel in steering wheel is defined by parameters like steering effort, manoeuvrability, on-center feel & response, cornering feel & response, Torque dead band, return-ability etc. and is influenced by a long list of components and systems in the truck. This study focuses on the influences of jacking torque and steering system friction on the on-center driving performance. Experiments to measure the Jacking torque and steering system friction were conducted in the lab and subjective and objective assessments of on-center driving performance were later conducted at test track in two similar 12 Ton truck to correlate their effects.
2017-01-10
Technical Paper
2017-26-0345
Bharat Kushwaha, Sanjay Chaudhuri, Sujatha Chandramohan
Abstract This paper investigates the yaw dynamic behaviour of a seven axle tractor semitrailer combination vehicle developed by VRDE (Vehicle Research & Development). The semitrailer has four steerable axles which follow command steering law i.e. all axles of semitrailer are steered in a particular relation with articulation of tractor. A 4 dof (degree of freedom) linear yaw plane model was developed for this combination vehicle. Yaw response characteristics such as lateral acceleration, yaw rate and articulation angle for step and sine steer is obtained from this model. Effects of speed on the above parameters are also studied to the same steering inputs. Lateral tyre forces due to semitrailer steering at various speeds are estimated to understand its distribution on each axle. Steady state yaw rate and articulation angle gain are obtained to predict the understeer / oversteer behaviour of combination vehicle.
Viewing 1 to 30 of 1483