Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 5007
CURRENT
2017-03-24
Standard
AMS5339G
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-03-24
Standard
AMS5085J
This specification covers a carbon steel in the form of sheet, strip, and plate.
CURRENT
2017-03-23
Standard
J1392_201703
This SAE Recommended Practice covers seven levels of high strength carbon and low-alloy hot rolled sheet and strip, cold rolled sheet, and coated sheet steels. The strength is achieved through chemical composition and special processing.
CURRENT
2017-03-23
Standard
AMS5824F
This specification covers a corrosion resistant steel in the form of welding wire.
CURRENT
2017-03-22
Standard
J2340_201703
This SAE Recommended Practice defines and establishes mechanical property ranges for seven grades of continuously cast high strength automotive sheet steels that can be formed, welded, assembled, and painted in automotive manufacturing processes. The grade of steel specified for an identified part should be based on part requirements (configuration and strength) as well as formability. Material selection should also take into consideration the amount of strain induced by forming and the impact strain has on the strength achieved in the finished part. These steels can be specified as hot-rolled sheet, cold-reduced sheet, uncoated, or coated by hot dipping, electroplating, or vapor deposition of zinc, aluminum, and organic compounds normally applied by coil coating. The grades and strength levels are achieved through chemical composition and special processing. Not all combinations of strength and coating types may be commercially available. Consult your steel supplier for details.
CURRENT
2017-03-21
Standard
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
CURRENT
2017-03-17
Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
2017-03-16
WIP Standard
ARP1820C
This practice provides a method of evaluating microhardness and microstructure very close to the surface of a disk specimen. It is useful for process control in heat treatment of steel parts to detect nitriding and carburization as well as decarburization and excessive intergranular oxidation. It also may be valuable for other evaluations, e.g., plated coatings and other materials.
2017-03-02
WIP Standard
AMS5358D
This specification covers a corrosion-resistant steel in the form of investment castings.
2017-03-02
WIP Standard
AMS5363F
This specification covers a corrosion and heat resistant steel in the form of sand or centrifugal castings.
2017-03-02
WIP Standard
AMS5657D
Bars, forgings, and forging stock.
2017-03-02
WIP Standard
AMS5623D
This specification covers a high-expansion steel in the form of bars, forgings, and forging stock.
2017-03-02
WIP Standard
AMS5624F
This specification covers an alloy steel in the form of bars 1 inch (25.4 mm) and under in nominal diameter or distance between parallel sides. Primarily for bolts and screws requiring a coefficient of thermal expansion approaching that of aluminum alloys. This steel is hardenable only by cold working.
2017-03-02
WIP Standard
AMS5549H
This specification covers a corrosion and moderate heat resistant steel in the form of plate.
2017-03-02
WIP Standard
AMS5683G
This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire.
2017-03-02
WIP Standard
AMS5672D
This specification covers a corrosion-resistant steel in the form of wire. Primarily for springs requiring corrosion resistance and high strength up to 600 degrees F (315 degrees C).
2017-03-02
WIP Standard
AMS5691H
This specification covers a corrosion and heat resistant steel in the form of covered welding electrodes. Primarily for shielded-metal-arc welding of parts fabricated from steels of similar composition, particularly when the weld zone is required to have strength and corrosion-resistance comparable to those of the parent metal.
2017-03-02
WIP Standard
AMS6532G
This specification covers a premium aircraft-quality alloy steel in the form of bars, forgings, and forging stock.
2017-03-02
WIP Standard
AMS5351G
This specification covers a corrosion and moderate heat resistant steel in the form of sand castings.
2017-03-02
WIP Standard
AMS5341D
This specification has been declared "NONCURRENT" by the Aerospace Materials Division, SAE, as of January 1995. It is recommended, therefore, that this specification not be specified for new designs.
2017-03-02
WIP Standard
AMS5348C
This specification has been declared "NONCURRENT" by the Aerospace Materials Division, SAE, as of January 1995. It is recommended, therefore, that this specification not be specified for new designs.
2017-03-02
WIP Standard
AMSSTD753B
This standard describes general and detailed methods of sampling and testing for surface passivity of corrosion-resistant steel parts. These tests may also be useful to determine if there is a need for passivation.
2017-03-02
WIP Standard
AMS5546E
This specification covers a corrosion and moderate heat resistant steel in the form of sheet and strip.
CURRENT
2017-03-01
Standard
AMS6509A
This specification covers a premium aircraft-quality alloy steel in the form of bars 199 in2 (1284 cm2) and under in cross section, forgings, and forging stock.
CURRENT
2017-02-21
Standard
AS4536C
This procurement specification covers aerospace quality safety cable kits consisting of safety cables and ferrules made from the same corrosion and heat resistant steels and a nickel base alloy of the type identified under the Unified Numbering system as follows: a. UNS S30400 - Corrosion resistant steel (AMS 5697) b. UNS S32100 - Corrosion and heat resistant steel (AMS 5689) c. UNS N06600 - Nickel base alloy (AMS 5687) d. UNS N06625 - Nickel Alloy, Corrosion Resistant (AMS 5666) The requirements for installation practices are also specified.
CURRENT
2017-02-17
Standard
AS27642/1
Add CREN version to the AS27642
CURRENT
2017-02-15
Standard
AMS5047G
This specification covers an aluminum-killed carbon steel in the form of sheet and strip.
Viewing 1 to 30 of 5007

Filter

  • Standard
    5007