Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 131
2016-10-06
WIP Standard
ARP4005C
This SAE Aerospace Recommended Practice (ARP) provides information to guide in the selection of electromechanical relays to be used in electrical/electronic circuits for application in aerospace, ground, and shipboard systems to achieve proper performance.
2016-03-14
WIP Standard
AS58091B
The primary function of this specification is to cover the general requirements of one-, two-, and three-pole trip-free circuit breakers for use in aircraft electric systems conforming to MIL-STD-704. As a secondary function, this specification may possibly cover the general requirements of one-, two- and three-pole circuit breakers for use in primary vehicles, other than aircraft, when mounted directly to the structure. An Amendment corresponding to this standard is available at AS58091_A1
2015-04-17
WIP Standard
AS24509B
An Amendment corresponding to this standard is available at AS24509_A2
2015-02-18
WIP Standard
AS24510B
An Amendment corresponding to this standard is available at AS24510_A2
2015-02-11
WIP Standard
AS5692B
The primary function of this specification is to cover the general requirements for manual reset trip-free arc fault/thermal circuit breakers for use in aircraft electrical systems conforming to MIL-STD-704. As a secondary function, this specification may possibly cover the general requirements for AFCBs for use in primary vehicles, other than aircraft, when mounted directly to the structure.
2015-02-11
WIP Standard
AS6019A
The primary function of this specification is to cover the general requirements for 28 VDC manual reset trip-free arc fault/thermal circuit breakers for use in aircraft electrical systems conforming to MIL-STD-704. As a secondary function, this specification may possibly cover the general requirements for AFCBs for use in primary vehicles, other than aircraft, when mounted directly to the structure.
2014-10-23
WIP Standard
ARP1199C
This Aerospace Recommended Practice provides technical and application information needed by the designers of aircraft electric systems and support equipment for the selection of overcurrent protective devices. It provides definitions to permit comparisons of various electric circuit protective devices. Included also are recommended procedures for periodic inspection.
2014-08-18
WIP Standard
J98
This SAE Standard is intended to be used as a guide for manufacturers and users of general purpose industrial machines to provide a reasonable degree of protection for personnel during normal operation and servicing. This document excludes skid steers which are covered by SAE J1388. Avoidance of accidents also depends upon the care exercised by such persons (see SAE J153). Inclusion of this standard instate, federal, or any laws or regulations where flexibility of revision is lacking is discouraged.
CURRENT
2014-07-09
Standard
J232_201407
This SAE Standard establishes performance criteria for towed, semi-mounted, or mounted and arm type rotary mowers with one or more blade assemblies of 77.5 cm blade tip circle diameter or over, mounted on a propelling tractor or machine of at least 15 kW, intended for marketing as industrial mowing equipment and designed for cutting grass and other growth in public use areas such as parks, cemeteries, and along roadways and highways. The use of the word “industrial” is not to be confused with “in-plant industrial equipment.” This document does not apply to: a. Turf care equipment primarily designed for personal use, consumption, or enjoyment of a consumer in or around a permanent or temporary household or residence. b. Equipment designed primarily for agricultural purposes but which may be used for industrial use. c. Self-powered or self-propelled mowers or mowing machines.
CURRENT
2014-07-09
Standard
J1001_201407
The guidelines for operator and bystander protection in this recommended practice apply to towed, semimounted or mounted flail mowers and flail power rakes when powered by a propelling tractor or machine of at least 15 kw (20 hp), intended for marketing as industrial mowing equipment and designed for cutting grass and other growth in public use areas such as parks, cemeteries and along roadways and highways. The use of the word "industrial" is not to be confused with "in-plant industrial equipment". This document does not apply to: 1. Turf care equipment primarily designed for personal use, consumption or enjoyment of a consumer in or around a permanent or temporary household or residence. 2. Machines designed primarily for agricultural purposes but which may be used for industrial use. 3. Self powered or self propelled mowers or mowing machines.
CURRENT
2014-06-17
Standard
AS25337A
CURRENT
2013-12-17
Standard
J1308_201312
This practice applies to guarding of engine cooling fans used on Off-Road Self-Propelled Work Machines defined in SAE J1116. It does not include guarding for belts, pulleys, or other rotating equipment used on these machines.
CURRENT
2013-03-26
Standard
J1388_201303
This SAE Standard is intended to provide personnel protection guidelines for skid steer loaders. This document is intended as a guide towards standard practice, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. This document provides performance criteria for newly manufactured loaders and it is not intended for in-service machines.
CURRENT
2012-07-23
Standard
J686_201207
This SAE Standard establishes basic dimensions for motor vehicle license plates. It is based on data supplied by the American Association of Motor Vehicle Administrators, Motor Vehicle manufacturers Association, and Motorcycle, Scooter and Allied Trades Association. The dimensions established in this document have considered legibility and identification of the license plate.
CURRENT
2012-07-23
Standard
J1044_201207
This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853, J187, J272, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that review and coordination of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.
CURRENT
2012-06-29
Standard
J1042_201206
This SAE Standard applies to General-Purpose Industrial Machines described in Category 2 of SAE J1116, but excludes skid steer loaders (covered by SAE J1388). Protection for the operator of an attachment (for example, a backhoe) is excluded from the scope of this document.
CURRENT
2012-05-31
Standard
AS58091A
The primary function of this specification is to cover the general requirements of one-, two-, and three-phase (often referred to as poles) trip-free circuit breakers for use in aircraft electric systems conforming to MIL-STD-704. As a secondary function, this specification may possibly cover the general requirements of one-, two- and three-phase circuit breakers for use in primary vehicles, other than aircraft, when mounted directly to the structure.
CURRENT
2010-08-05
Standard
J129_201008
This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.
CURRENT
2009-10-29
Standard
J853_200910
This SAE Standard has been established to provide direction for the design and installation of a Vehicle Identification Number assigned to a passenger car or truck. In adhering to these standards, facility of application in factory production and appearance are matters for manufacturer control.
CURRENT
2009-10-29
Standard
J187_200910
This SAE Recommended Practice has been established to provide direction for the design and installation of a vehicle identification number assigned to a truck or truck-tractor. In adhering to these standards, facility of application in factory production and appearance are matters for manufacturer control.
CURRENT
2009-10-29
Standard
J218_200910
This recommended practice is intended to provide uniform nomenclature and definitions for the primary levels of vehicle identification, with particular application to passenger cars.
CURRENT
2009-10-29
Standard
J1229_200910
This SAE Recommended Practice is intended to provide uniform nomenclature and definitions for the primary levels of vehicle identification, with particular application to trucks.
HISTORICAL
2009-05-11
Standard
J232_200905
This SAE Standard establishes performance criteria for towed, semi-mounted, or mounted and arm type rotary mowers with one or more blade assemblies of 77.5 cm blade tip circle diameter or over, mounted on a propelling tractor or machine of at least 15 kW, intended for marketing as industrial mowing equipment and designed for cutting grass and other growth in public use areas such as parks, cemeteries, and along roadways and highways. The use of the word "industrial" is not to be confused with "in-plant industrial equipment." This document does not apply to: a. Turf care equipment primarily designed for personal use, consumption, or enjoyment of a consumer in or around a permanent or temporary household or residence. b. Equipment designed primarily for agricultural purposes but which may be used for industrial use. c. Self-powered or self-propelled mowers or mowing machines.
HISTORICAL
2009-05-11
Standard
J1001_200905
The purpose of this report is to establish guidelines for operator and bystander protection for flail mowers and flail power rakes whose intended use falls within the scope of this document. The guidelines for operator and bystander protection in this recommended practice apply to towed, semi-mounted or mounted flail mowers and flail power rakes when powered by a propelling tractor or machine of at least 15 kw (20 hp), intended for marketing as industrial mowing equipment and designed for cutting grass and other growth in public use areas such as parks, cemeteries and along roadways and highways. The use of the word 'industrial' is not to be confused with 'in-plant industrial equipment.'
CURRENT
2009-04-13
Standard
J819_200904
This SAE Standard applies to all self-propelled construction and industrial machines using liquid-cooled internal combustion engines.
Viewing 1 to 30 of 131

Filter

  • Standard
    131