Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 370
CURRENT
2017-02-23
Standard
J1301_201702
The scope and purpose of this SAE Recommended Practice is to provide a classification system for deformation sustained by trucks involved in collisions on the highway. Application of the document is limited to medium trucks, heavy trucks, and articulated combinations. The TDC classifies collision contact deformation, as opposed to induced deformation, so that the deformation is segregated into rather narrow limits or categories. Studies of collision deformation can then be performed on one or many data banks with assurance that data under study are of essentially the same type. Many of the features of the SAE J224 MAR80 have been retained in this document, although the characters within specific columns vary. Each document must therefore be applied to the appropriate vehicle type. It is also important to note that the Truck Deformation Classification (TDC) does not identify specific vehicle configurations and body types.
CURRENT
2017-02-22
Standard
J3057_201702
This SAE Recommended Practice describes the test procedures for conducting quasi-static modular body strength tests for ambulance applications. Its purpose is to establish recommended test practices which standardize the procedure for Type I and Type III bodies, provide ambulance builders and end-users with testing procedures and, where appropriate, provide acceptance criteria that, to a great extent, ensures the ambulance structure meets the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2017-01-18
Standard
J2419_201701
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2017-01-06
Standard
J167_201701
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
CURRENT
2016-11-28
Standard
J2194_201611
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met.
CURRENT
2016-11-23
Standard
J1194_201611
Fulfillment of the intended purpose requires testing as follows:
CURRENT
2016-11-18
Standard
J2258_201611
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles. The safety specifications in this document apply to any self-propelled, operator-controlled, off-highway vehicle 1829 mm (72 in) or less in overall width, exclusive of added accessories and attachments, operable on three or more wheels or tracks, primarily intended to transport material loads or people, with a gross vehicle weight of 2500 kg (5500 lb) or less, and a maximum design speed less than or equal to 40.23 km/h (25 mph). This document is not intended to cover Go-Karts (ASTM F2007-07a), Fun-Karts (ASTM F2011-02e1), Dune Buggies, and all terrain vehicles (ATVs) complying with ANSI/SVIA 1.
CURRENT
2016-11-18
Standard
J2358_201611
This SAE Standard defines the safety and performance requirements for Low Speed Vehicles (“LSV”). The safety specifications in this document apply to any powered vehicle with a minimum of 4-wheels, a maximum level ground speed of more than 32 km/h (20 mph) but not more than 40 km/h (25 mph),), and a maximum gross vehicle weight of 1361 kg (3000 pounds), that is intended for operating on designated roadways where permitted by law.
CURRENT
2016-11-01
Standard
J3026_201611
This SAE Recommended Practice describes the testing procedures that may be used to evaluate the integrity of ground ambulance-based occupant seating and occupant restraint systems for workers and civilians transported in the patient compartment of an ambulance when exposed to a frontal or side impact. This Recommended Practice was based on ambulance patient compartment dynamics and is not applicable to other vehicle applications or seating positions. This Recommended Practice is structured to accommodate seating systems installed in multiple attitudes including but not limited to side-facing, rear-facing, and forward-facing.
CURRENT
2016-11-01
Standard
J3058_201611
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
CURRENT
2016-11-01
Standard
J3027_201611
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when exposed to a frontal, side or rear impact. Its purpose is to provide litter manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent ensures the patient litter, litter retention system, and patient restraint utilizes a similar dynamic performance test methodology to that which is applied to other vehicle seating and occupant restraint systems. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
2016-09-12
WIP Standard
J3126
This recommended practice provides technicians with safe and efficient techniques and general equipment recommendations for servicing Mobile Air Conditioning (MAC) systems in heavy duty and off-highway work machines. Presently, R-134a is the only approved refrigerant for use in mobile heavy duty and off-highway equipment and therefore this document primarily covers the servicing of R-134a systems. Since the technician may encounter other refrigerants a brief explanation on the identification safe handling of each refrigerant will be introduced.
CURRENT
2016-08-23
Standard
J2956_201608
This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J2917_201608
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J3044_201608
This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-02
Standard
J284_201608
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
2016-06-13
WIP Standard
AS6228A
This SAE Aerospace Standard (AS) covers the requirements and technical guidance for evaluation of life-cycle cost, productivity, and safety/health factors related to power hand tool selection. It applies approaches to selection of quieter and lower vibration hand-held powered tools, with optimal ergonomic features, for the prevention of Hand-Arm Vibration Syndrome (HAVS), hearing loss and repetitive motion injuries. It suggests use of noise and vibration data provided by vendors to be verified and supplemented by information available through the National Institute for Occupational Safety and Health (NIOSH) and European Union databases. Inclusion/exclusion of data in this document is not intended to imply that all of the products described herein are the only production models that meet this standard. Consumers are requested to consult with manufacturers concerning lists of stock production models that meet this standard.
2016-03-09
WIP Standard
J3045/1
The specification will provide objective criteria for acceptance of the test procedures given SAE J3045-1, of the LDWS (e.g., ability to detect lane presence, and ability to detect an unintended lane departure), its ability to indicate LDWS engagement, its ability to indicate LDWS disengagement, and determine the point at which the LDWS notifies the Human Machine Interface (HMI) or vehicle control system that a lane departure event is detected. The HMI is not addressed herein, but is considered in SAE Standard J2808.
CURRENT
2016-01-14
Standard
J2292_201601
This SAE Recommended Practice establishes minimum performance and test requirements for combination pelvic and upper torso occupant restraint systems provided for off-road self-propelled work machines.
CURRENT
2015-11-24
Standard
J2641_201511
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
CURRENT
2015-11-24
Standard
J1038_201511
This SAE Recommended Practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children's snowmobile as identified in 1.2.
CURRENT
2015-10-22
Standard
J3029_201510
This SAE Recommended Practice (RP) establishes uniform powered vehicle level test procedure for Forward Collision Avoidance and Mitigation (FCAM) systems (also identified as Automatic Emergency Braking (AEB) systems) used in highway commercial vehicles and coaches greater than 4535 Kg (10,000 lb.) GVWR. This RP does not apply to trailers, dollies, etc. and does not intend to exclude any particular system or sensor technology. These FCAM systems utilize various methodologies to identify, track and communicate data to the operator and vehicle systems to warn, intervene and/or mitigate in the longitudinal control of the vehicle.
2015-10-14
WIP Standard
J1241
This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered.
CURRENT
2015-10-08
Standard
J3078/6_201510
SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
2015-10-07
WIP Standard
J3113
SAE Jxxxx provides principles and a process for developing icons for use in electronic displays related to Off Road Work Machines as stated defined in SAE J 1116. Following the process insures that icons are derived from ISO registered graphical symbols or ISO compliant non-registered graphical symbols.
2015-09-29
WIP Standard
J386
This standard provides performance and test requirements for operator restraint systems provided for off-road self-propelled work machines. This document applies to pelvic restraint systems (Type 1) for off-road, self-propelled work machines fitted with ROPS and commonly used in construction, earthmoving, forestry, and mining as referred to in SAE J1040 and industrial machines fitted with ROPS as referred to in SAE J1042.
CURRENT
2015-08-27
Standard
J2418_201508
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2015-07-30
Standard
J3045_201507
This SAE recommended practice establishes a uniform, powered vehicle T.P. for lane departure warning systems used in highway trucks and buses greater than 4,546 kg (10,000 lb) GVW. Systems similar in function but different in scope and complexity, including Lane Keeping/Lane Assist and Merge Assist, are not included in this T.P. This T.P. does not apply to trailers, dollies, etc. This T.P. does not intend to exclude any particular system or sensor technology. The specification will test the functionality of the LDWS (e.g., ability to detect lane presence, and ability to detect an unintended lane departure), its ability to indicate LDWS engagement, its ability to indicate LDWS disengagement, and determine the point at which the LDWS notifies the Human Machine Interface (HMI) or vehicle control system that a lane departure event is detected. The HMI is not addressed herein, but is considered in SAE Standard J2808.
2015-06-05
WIP Standard
J3102
This SAE Recommended Practice describes the dynamic and static testing procedures required to evaluate the integrity of the ambulance substructure, to support the safe mounting of a SAE J3027 compliant litter retention device or system, when exposed to a frontal, side or rear impact (i.e. a crash impact). Its purpose is to provide manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure the ambulance substructure meets the same performance criteria across the industry. Prospective manufacturers or vendors have the option of performing either dynamic testing or static testing. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
CURRENT
2015-06-04
Standard
J2426_201506
This SAE Recommended Practice describes the test procedures for conducting simulated dynamic lateral rollover restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
Viewing 1 to 30 of 370