Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 149
CURRENT
2017-05-25
Standard
AS1043G
SCOPE IS UNAVAILABLE.
CURRENT
2017-05-19
Standard
J2591_201705
This SAE Recommended Practice applies to motor vehicle Forward Illumination Devices which incorporate limited adaptive beam pattern capabilities. This document is to be used in conjunction with other forward lighting standards and/or recommended practices which define the base beam procedures, requirements, and guidelines.
2017-05-09
WIP Standard
J2042
This SAE Standard provides test procedures, requirements, and guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. A clearance lamp, sidemarker lamp, or an identification lamp conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.
CURRENT
2017-04-13
Standard
AIR36105B
The present SAE Aerospace Information Report (AIR) provides a list of the main government regulations, SAE and international standards, and standing industry recommendations applying to air cargo unit load devices (pallets, nets, and containers) to be loaded with either baggage or freight on board civil transport aircraft. It is intended to provide unit load devices designers, purchasers, and operators as well as civil transport aircraft and aircraft cargo systems designers within the industry with a list of the available document references to cover the other aspects that do not all directly pertain to airworthiness and testing, listed in 1.1 of AS36100, – Air Cargo Unit Load Devices - Performance Requirements and Test Parameters [TSO-C90].
2017-02-03
WIP Standard
ARP6199B

This SAE Aerospace Recommended Practice (ARP) is only applicable to 14 CFR part 25 Transport Airplane passenger seats. This document provides an approach for determining which parts on aircraft seats are required to meet the test requirements of 14 CFR part 25 Appendix F, Parts IV and V. Such materials are referred to as Heat Release Special Conditions (HRSC) compliant]. Additionally, it is recommended to use HRSC compliant materials in applications where not required.

Independent furniture related to seat installations is outside the scope of this document.

CURRENT
2017-02-02
Standard
ARP6199A
This SAE Aerospace Recommended Practice (ARP) is only applicable to 14 CFR part 25 Transport Airplane passenger seats. This document provides an approach for determining which parts on aircraft seats are required to meet the test requirements of 14 CFR part 25 Appendix F, Parts IV and V. Such materials are referred to as Heat Release Special Conditions (HRSC) compliant]. Additionally, it is recommended to use HRSC compliant materials in applications where not required. Independent furniture related to seat installations is outside the scope of this document.
2016-12-14
WIP Standard
AS6316
This SAE Aerospace Standard (AS) documents a common understanding of terms, compliance issues and occupant injury criteria to facilitate the design and certification of oblique facing passenger seat installations specific to Part 25 aircraft.
CURRENT
2016-12-13
Standard
AS8049/1B
This SAE Aerospace Standard (AS) defines Minimum Performance Standards (MPS), qualification requirements, and minimum documentation requirements for side-facing seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a side-facing seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic test conditions set forth in Title 14, Code of Federal Regulations (CFR) Part 23, 25, 27, or 29. While this document addresses system performance, responsibility for the seating system is divided between the seat supplier and the installation applicant. The seat supplier’s responsibility consists of meeting all the seat system performance requirements and obtaining and supplying to the installation applicant all the data prescribed by this document.
2016-11-21
WIP Standard
J3134
This SAE Recommended Practice provides test procedures, performance requirements, and design guidelines for autonomous vehicle lighting.
CURRENT
2016-11-18
Standard
J2258_201611
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles. The safety specifications in this document apply to any self-propelled, operator-controlled, off-highway vehicle 1829 mm (72 in) or less in overall width, exclusive of added accessories and attachments, operable on three or more wheels or tracks, primarily intended to transport material loads or people, with a gross vehicle weight of 2500 kg (5500 lb) or less, and a maximum design speed less than or equal to 40.23 km/h (25 mph). This document is not intended to cover Go-Karts (ASTM F2007-07a), Fun-Karts (ASTM F2011-02e1), Dune Buggies, and all terrain vehicles (ATVs) complying with ANSI/SVIA 1.
CURRENT
2016-11-18
Standard
J2358_201611
This SAE Standard defines the safety and performance requirements for Low Speed Vehicles (“LSV”). The safety specifications in this document apply to any powered vehicle with a minimum of 4-wheels, a maximum level ground speed of more than 32 km/h (20 mph) but not more than 40 km/h (25 mph),), and a maximum gross vehicle weight of 1361 kg (3000 pounds), that is intended for operating on designated roadways where permitted by law.
CURRENT
2016-11-03
Standard
J2498_201611
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the system of optical warning devices used on emergency vehicles.
2016-10-13
WIP Standard
J587
This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.
2016-10-07
WIP Standard
ARP6909
This SAE XXX defines acceptable methods for determining the seat reference point (SRP), and the documentation requirements for that determination, for passenger and crew seats in Transport Aircraft, Civil Rotorcraft and General Aviation Aircraft.
CURRENT
2016-09-09
Standard
J592_201609
This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.
CURRENT
2016-06-30
Standard
J3069_201606
This SAE Recommended Practice provides test procedures, performance requirements, and design guidelines for adaptive driving beam (ADB) and associated equipment.
2016-06-07
WIP Standard
AIR6908
This document provides informational background, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and acceptance criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP 6330 defines multiple test methods uses to assess the effect of seat back mounted IFE monitor changes on head blunt trauma.
CURRENT
2016-05-13
Standard
ARP6316
This SAE Aerospace Recommended Practice (ARP) documents a common understanding of terms, compliance issues, and occupant injury criteria to facilitate the design and certification of oblique facing passenger seat installations specific to Part 25 aircraft. The applicability of the criteria listed in this current release is limited to seats with an occupant facing direction greater than 18 and no greater than 30 degrees relative to the aircraft longitudinal axis. Later revisions are intended to provide criteria for other facing directions. Performance criteria for side facing seats installed with the occupant facing direction at 90 degrees relative to the aircraft longitudinal axis are provided in AS8049/1. Seats installed at angles greater than 30 degrees relative to the aircraft longitudinal axis must have an energy absorbing rest or shoulder harness. However, this document does not provide the criteria for oblique facing seats incorporating such rests.
CURRENT
2015-10-28
Standard
J1373_201510
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
CURRENT
2015-07-08
Standard
J1133_201507
This document provides design guidelines, test procedure references, and performance requirements for stop arm lamp devices on school bus vehicles which are used to alert traffic to stop when passengers are loading and unloading
CURRENT
2015-07-08
Standard
J887_201507
This document provides design guidelines, test procedure references, and performance requirements for red and yellow overhead warning devices on school bus vehicles which are used to alert traffic to stop when passengers are loading and unloading.
2015-04-30
WIP Standard
J3098
This SAE Recommended Practice applies to front signature lamps installed on the front exterior of motor vehicles intended only to be decorative in nature and are also intended not to impair the effectiveness of any required lighting device. This recommended practice establishes uniformity in use guidelines for the performance, installation, activation and switching of front signature lamps.
2015-04-14
WIP Standard
J2938
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the methods of the measurement of lumen maintenance of LED devices (packages, arrays and modules). This document does not provide guidance or make any recommendation regarding predictive estimations or extrapolation for lumen maintenance beyond the limits of the lumen maintenance determined from actual measurements.
CURRENT
2015-02-17
Standard
J567_201502
This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning light source (bulb) sockets, light source (lamp) holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.
2015-01-16
WIP Standard
J845
This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
2014-11-18
WIP Standard
ARP6337
Define and develop test parameters, test methods, measurements, and acceptable performance criteria for composite aircraft seat structures.
CURRENT
2014-08-11
Standard
J914_201408
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for side turn signal lamps for vehicles less than 12 m in length.
CURRENT
2014-06-17
Standard
J585_201406
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than 2032 mm in overall width.
2014-05-27
WIP Standard
ARP6330
Methods will be developed to characterize In Flight Entertainment (IFE) component impact performance separate from seat design. These methods will address both initial seat head impact criterion (HIC) testing and subsequent IFE component changes. Methods will evaluate head blunt trauma, post-impact sharp edges, and egress impediment. Criteria development will involve defining test methods, test parameters, measurements, and acceptance criteria. Particular emphasis on evaluating IFE changes that require coordination and evaluation per SAE ARP 6448, Appendix B.
CURRENT
2014-05-16
Standard
AIR6160
This document provides informational background, rationale and a technical case to allow consideration of the removal of the magnesium alloy restriction in aircraft seat construction as contained in AS8049B. The foundation of this argument is flammability characterization work performed by the FAA at the William J. Hughes Technical Center (FAATC), Fire Safety Branch in Atlantic City, New Jersey, USA. The rationale and detailed testing results are presented along with flammability reports that have concluded that the use of specific types of magnesium alloys in aircraft seat construction does not increase the hazard level potential in the passenger cabin in a post-crash fire scenario. Further, the FAA has developed a lab scale test method, reference DOT/FAA/TC-13/52, to be used as a certification test, or method of compliance (MOC) to allow acceptability of the use of magnesium in the governing TSO-C127 and TSO-C39C.
Viewing 1 to 30 of 149

Filter

  • Standard
    149