Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 48
2017-10-31
WIP Standard
SAE1002
Latitude and Longitude is not a reference system commonly used by land-based First Responders. Street names and associated addresses are, but following disasters such as floods, fires, etc., they are often obscured or destroyed. The USNG is a point and area location grid reference system that provides a reliable and available geoaddressing capability that is an easy to use alternative to latitude and longitude.
2017-09-21
WIP Standard
SAE9990/1
This eLoran transmitted signal standard provides technical descriptions of a data channel based on the tri-state pulse position modulation technique.
2017-09-21
WIP Standard
SAE9990/2
This eLoran transmitted signal standard provides technical descriptions of the data channel using 9th pulse modulation technique.
2017-08-08
WIP Standard
GEIASTD0005_1B

This standard defines the objectives of, and requirements for, documenting processes that assure customers and regulatory agencies that ADHP electronic systems containing Pb-free solder, piece parts, and PBs will satisfy the applicable requirements for performance, reliability, airworthiness, safety, and certifiability throughout the specified life of performance.

It is intended to communicate requirements for a Pb-free Control Plan (LFCP), hereinafter referred to as the Plan, and to assist the Plan Owners in the development of their own Plans. The Plan documents the Plan Owner’s processes that assure their customers, and all other stakeholders that the Plan Owner's products will continue to meet their requirements, given the risks stated in the Introduction.

2017-07-06
WIP Standard
SAE1001
The purpose of the "Integrated Project Processes for Engineering a System(IPPES)" Standard is to provide an integrated set of fundamental technical processes to aid a project in the engineering or reengineering of a system over the full life cycle. Covers systems that can be any combination of people (humans); product (hardware or software); or process (service). Applicable to any type of system: commercial or non-commercial; small or large, simple or complex, precedented or unprecedented; new or legacy or any combination of these characteristics.
2017-06-07
WIP Standard
GEIASTD0005_2B
This Standard establishes processes for documenting the mitigating steps taken to reduce the harmful effects of Pb-free tin finishes in electronic systems. This Standard is applicable to Aerospace, Defense, and High Performance (ADHP) electronic applications which procure equipment that may contain Pb-free tin finishes.
CURRENT
2017-05-24
Standard
AIR5742A
The scope of this document is related to the particular needs of oxygen equipment with regards to packaging and transportation. The document provides guidance for handling chemical, gaseous and liquid oxygen equipment. It summarizes national and international regulations to be taken into account for transportation on land, sea and air and provides information on classification of hazardous material. The aim of this document is to summarize information on packaging and transportation of oxygen equipment. Statements and references to regulations cited herein are for information only and should not be considered as interpretation of a law. Processes to maintain cleanliness of components and subassemblies during processing and assembly or storage of work-in-progress are outside the scope of this document. Guidance on this can be obtained from ARP1176.
2017-04-14
WIP Standard
STD0016A
This document defines the requirements for developing a DMSMS Management Plan, hereinafter also called the Plan, to assure customers that the Plan owner is using a proactive DMSMS process for minimizing the cost and impact that part and material obsolescence will have on equipment delivered by the Plan owner. The technical requirements detailed in clause 5 ensure that the Plan owner can meet the requirement of having a process to address obsolescence as required by Industry Standards such as EIA-4899 "Standard for Preparing an Electronic Components Management Plan" and DoD Programs as required by MIL-STD-3018 "Parts Management". Owners of DMSMS Management Plans include System Integrators, Original Equipment Manufacturers (OEM), and logistics support providers.
CURRENT
2016-07-12
Standard
GEIAOP0003
This handbook details the TechAmerica Technical Fellowship Selection Process. It identifies the tasks to be performed and associates them with participants in the process. The focus is intended to keep the process implementation as uniform as possible. There are three types of information in this handbook: Process details Candidate Application Package format Process infrastructure and description Each Section of this handbook describes a significant segment of the selection process. There are also appendices that contain a variety of supporting material relevant to the different process participants.
CURRENT
2015-12-19
Standard
AS6163
This SAE Aerospace Standard (AS) defines the minimum performance standard to demonstrate compliance with the regulatory design, test and operational requirements for a Temperature Controlled Container (TCC).
CURRENT
2015-12-17
Standard
J1698/3_201512
This SAE Recommended Practice defines procedures intended to be used to validate that relevant EDR output records conform within specified limits to measured sensor input to the device.
2015-10-21
WIP Standard
GEIASTD0007C
This standard defines logistics product data generated during the requirements definition and design of an industry or government system, end item or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a standard set of data tags for all or portions of logistics product data and customer defined sub-sets of logistics product data. The standard can be applied to any indsutry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity.
2015-10-21
WIP Standard
GEIAHB0007C
This handbook is intended to provide additional information on the use and tailoring of the data in GEIA-STD-0007. The standard provides a new approach to Logistics Support Analysis Record (LSAR) (i.e., MIL-STD-1388-2B) data with emphasis on data transfer (e.g., XML Schemas) versus data storage (e.g., relational tables). GEIA-STD-0007 identifies the range of logistics product data that is generated during the development and acquisition of a system or end item. It does not prescribe the supportability analyses required to generate logistics product data. How the data is generated via analysis techniques/tools, how it is stored and processed, and how the data is used to generate specific logistics support products, is left to the performing activity. GEIA-STD-0007 is a data transfer standard implementing the logistics data concepts of GEIA-STD-927, Common Data Schema for Complex Systems.
2015-10-13
WIP Standard
GEIASTD0008A
This Standard specifies the minimum derating requirements for using electronic components in moderately severe environments. These environments are assumed to include Airborne Inhabited Cargo (AIC), Airborne Inhabited Fighter (AIF), Ground Mobile (GM), and Naval Sheltered (NS) environments specified in MIL-HDBK-217. This Standard is intended to supersede the derating limits contained in Defense Standardization Program Office (DSPO) Standardization Directive SD-18, Naval Standard TE000-AB-GTP-010, and Air Force ESD-TR-85-148. It is intended that a future revision of this Standard will include additional requirements for derating for other environments (e.g. Airborne Uninhabited Cargo). Since this Standard specifies the minimum derating requirements, (sub)contractors may derate in excess of these requirements.
CURRENT
2015-07-01
Standard
EIA601A
This standard specifies requirements for the approval and maintenance of a manufacturer's capability and the procedures for the test and release of passive electronic components manufactured under capability approval. It also includes requirements for generic specifications that invoke this standard. It applies to all passive electronic components to be released under the capability requirements of an EIA generic and/or sectional and/or detail specification.
CURRENT
2015-07-01
Standard
EIA585
(From Standards Proposal No. 2358, formulated under the cognizance of the EIA Quality and Reliability Engineering (QRE) Committee.)
CURRENT
2015-07-01
Standard
EIA832
The procedure outlined in this document is applicable to any manufacturing or service process. It may be used on part of a process or and entire process or a series of sequential processes.
CURRENT
2015-07-01
Standard
EIA557B
The general requirements of an SPC system shall encompass, but are not limited to, the following elements: Overall quality system Management commitment SPC system documentation Critical process nodes Gage characterization and capability Process characterization and capability Control system documentation On-line/off-line control Training Supplier SPC systems Calibration Preventive maintenance Self audit
CURRENT
2014-11-14
Standard
TSB001_201411
CURRENT
2014-11-04
Standard
TSB004_201411
2014-10-22
WIP Standard
GEIASTD0009A
This standard requires the developers and customer/user's working as a team to plan and implement a reliability program that provides systems/products that satisfy the user's requirements and expectations. The user's requirements and needs are expressed in the form of the following four reliability objectives: The developer shall solicit, investigate, analyze, understand and agree to the user's requirements and product needs. The developer, working with the customer and user, shall include the activities necessary to ensure that the user's requirements and product needs are fully understood and defined, so that a comprehensive design specification and Reliability Program Plan can be generated; The developer shall use well-defined reliability- and systems-engineering processes to develop, design, and verify that the system/product meets the user's documented reliability requirements and needs.
2014-08-01
WIP Standard
GEIASTD0010A
This document outlines a standard practice for conducting system safety. The system safety practice as defined herein provides a consistent means of evaluating identified risks. Mishap risk must be identified, evaluated, and mitigated to a level as low as reasonably practicable. The mishap risk must be accepted by the appropriate authority and comply with federal (and state, where applicable) laws and regulations, executive orders, treaties, and agreements. Program trade studies associated with mitigating mishap risk must consider total life cycle cost in any decision. This document is intended for use as one of the elements of project solicitation for complex systems requiring a systematic evaluation of safety hazards and mitigating measures. The Managing Authority may identify, in the solicitation and system specification, specific system safety engineering requirements to be met by the Developer.
2014-07-01
WIP Standard
GEIAHB859A
The federal government and industry have moved to concurrent acquisition and development processes using integrated process teams (IPTs). These processes are supported by timely, accurate, cross functional access to data within an integrated data environment (IDE) enabled by advances in information technology (IT). Since the advent of acquisition reform in 1994, Data Management (DM) practices have evolved from being directed by a prescriptive set of standards and procedures to use of the guidance in a principles-based standard -- ANSI/EIA 859.

GEIA Handbook 859 provides implementation guidance for ANSI/EIA 859, with discussions of applications of the standard's principles, tools, examples, and case studies. Handbook 859 is organized according to the lifecycle of data management and covers activities from the pre-RFP stage through records disposition.

2014-06-19
WIP Standard
GEIATB0002A
This Bulletin is initially intended to be used to convey a combination of information to CM practitioners, both new and already skilled personnel alike. It provides the "what" of CM products and activities; with the "when" of CM correlated to DoD acquisition phases and milestones – thereby giving a time-phased depiction. The document spreadsheet should be read from top to bottom. It shows both the CM activities and products that should be performed and accomplished on a program or project. Next it provides a brief description of the CM activity or product and a column providing a reference(s) to other sources of information to learn even more about how the activity or product should be accomplished. Also included is a column for suggested level of CM control to be applied to the activity/product, from an Industry perspective. Future iterations will include a more complete dataset covering columns for entry criteria, exit criteria and related products from other skillcodes/disciplines.
CURRENT
2014-02-10
Standard
GEIAHB0007B
CURRENT
2013-05-01
Standard
GEIASTD927B
GEIA-STD-927 specifies the data concepts to be exchanged to share product information pertaining to a complex system from the viewpoints of multiple disciplines. It supports the exchange of data across the entire life cycle for the product from the concept stage through disposal.
CURRENT
2013-05-01
Standard
GEIASTD0007B
This standard defines logistics product data generated during the requirements definition and design of an industry or government system, end item or product. It makes use of the Extensible Markup Language (XML) through the use of entities and attributes that comprise logistics product data and their definitions. The standard is designed to provide users with a standard set of data tags for all or portions of logistics product data and customer defined sub-sets of logistics product data. The standard can be applied to any indsutry or government product, system or equipment acquisition program, major modification program, and applicable research and development projects. This standard is for use by both industry and government activities. As used in this standard, the requiring authority is generally the customer and the customer can be a government or industry activity. The performing activity may be either a industry or government activity.
CURRENT
2013-03-01
Standard
EIA748C
CURRENT
2012-12-01
Standard
GEIASTD0005_3A
This document defines: A default method for those companies that require a pre-defined approach and A protocol for those companies that wish to develop their own test methods. The default method (Section 4 of the document) is intended for use by electronic equipment manufacturers, repair facilities, or programs which, for a variety of reasons, may be unable to develop methods specific to their own products and applications. It is to be used when little or no other information is available to define, conduct, and interpret results from reliability, qualification, or other tests for electronic equipment containing Pb-free solder. The default method is intended to be conservative, i.e., it is biased toward minimizing the risk to users of AHP electronic equipment.
Viewing 1 to 30 of 48

Filter

  • Standard
    48