Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 337
2017-04-04
WIP Standard
AMS2249H
This specification defines limits of variation for determining acceptability of the composition of cast or wrought titanium and titanium alloy parts and material acquired from a producer. When specifically referenced in the material specification, the purchaser may apply check analysis limits to determine the acceptability of parts and materials at purchaser final acceptance or verification testing operation. Check analysis limits are not for producers use at producer’s acceptance testing. Composition of parts and materials must conform to the limits of the material specification. Check limits are not permitted for ladle or ingot analysis.
2017-04-04
WIP Standard
AMS4898E
This specification covers a titanium alloy in the form of sheet in nominal thicknesses 0.016 through 0.1874 inch (0.41 through 4.760 mm).
2017-04-04
WIP Standard
AMS4971L
This specification covers a titanium alloy in the form of bars, wire, forgings and flash welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides and stock for forging or flash welded rings of any size.
2017-04-04
WIP Standard
AMS4978H
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, and stock for forging or flash welded rings.
2017-04-04
WIP Standard
AMS4979J
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides and stock of any size for forging or flash welded rings.
CURRENT
2017-04-04
Standard
AMS4949B
This specification covers titanium in the form of laminated sheet.
2017-04-04
WIP Standard
AMS4902L
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate up through 1.000 inch (25.40 mm). This material typically has been used for parts requiring aqueous corrosion resistance, moderate strength up to 400 °F (204 °C) and oxidation resistance up to 600 °F (316 °C), but usage is not limited to such applications.
2017-04-04
WIP Standard
AMS4975N
This specification covers a titanium alloy in the form of bars, wire, flash welded rings 3.00 inches (76.2 mm) and under in nominal diameter or least distance between parallel sides and 16 square inches (103 cm2) and under in cross-sectional area and stock of any size for flash welded rings.
2017-04-04
WIP Standard
AMS4976K
This specification covers a titanium alloy in the form of forgings and forging stock.
2017-04-04
WIP Standard
AMS4981H
This specification covers a titanium alloy in the form of bars, wire, and forgings up through 4.000 inches (101.60 mm), inclusive, in diameter or least distance between parallel sides and forging stock of any size.
2017-03-31
WIP Standard
AMS6950
This specification covers a titanium alloy in the form of bars, wire, forgings, rings, and drawn shapes.
CURRENT
2017-03-30
Standard
AMS4933F
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and flash welded rings up through 4.000 in2 (25.81 cm2) cross-section and stock for flash welded rings.
CURRENT
2017-03-28
Standard
AMS4939C
This specification covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.60 mm) nominal thickness.
CURRENT
2017-03-28
Standard
AMS4959G
This specification covers a titanium alloy in the form of cold drawn wire.
HISTORICAL
2017-02-22
Standard
AMS4959F
This specification covers a titanium alloy in the form of cold drawn wire.
2016-10-21
WIP Standard
AMS4917J
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2016-10-11
WIP Standard
AMS7875F
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder. This product has been used typically for producing plasma spray coatings to provide wear and fretting resistant surfaces, but usage is not limited to such applications.
2016-10-10
WIP Standard
AMS4966R
This specification covers a titanium alloy in the form of forgings and forging stock. These forgings have been used typically for parts requiring strength up to 800 °F (427 °C) and that may be welded during fabrication, but usage is not limited to such applications.
2016-10-08
WIP Standard
AMS4998F
This specification covers a titanium alloy in the form of prealloyed powder. This powder has been used typically for compaction into net or near net shapes and into forging stock in the form of billets or preforms, but usage is not limited to such applications.
2016-10-08
WIP Standard
AMS2244D
This specification covers established manufacturing tolerances applicable to titanium and titanium alloy tubing. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.
2016-09-29
WIP Standard
AMS4954K
This specification covers a titanium alloy in the form of wire for welding filler metal.
2016-09-29
WIP Standard
AMS4915M
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm).
2016-09-29
WIP Standard
AMS2380G
This specification covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products.
2016-04-05
WIP Standard
AMS4940C
This specification covers one grade (Grade 1) of commercially-pure titanium in the form of sheet, strip, and plate up through a thickness of 1.000 inch (25.40 mm).
2015-09-27
WIP Standard
AMS2809B
This specification covers procedures for identifying wrought products of titanium and titanium alloys.
2015-03-31
WIP Standard
G15AA
New AMS for Ti-6-4 Seamless, Hydraulic Tubing including Technical, Quality and Testing Requirements
2015-01-23
WIP Standard
AMS2801C
This specification covers the engineering requirements for heat treatment by part fabricators (users) or their vendors or subcontractors, of parts (See 1.1.2) made from the following titanium alloys: Commercially Pure 6Al-4V(ELI) 3Al-8V-6Cr-4Mo-4Zr 3Al-2.5V 6Al-6V-2Sn 13V-11Cr-3Al 5AI-2.5Sn 6Al-2Sn-4Zr-2Mo 10V-2Fe-3Al 8Al-1Mo-1V 6AI-2Sn-4Zr-6Mo 15V-3Cr-3Al-3Sn
CURRENT
2014-07-31
Standard
AMS4989C
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 1.000 inch (25.40 mm), inclusive.
CURRENT
2014-07-23
Standard
AMSH81200D
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
CURRENT
2014-05-28
Standard
AMS4967L
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
Viewing 1 to 30 of 337

Filter

  • Standard
    337