Criteria

Text:
Content:
Display:

Results

Viewing 211 to 240 of 1425
CURRENT
2012-12-17
Standard
AMS2425F
This specification covers the requirements for gold deposited on metal surfaces and the properties of the deposit.
CURRENT
2012-12-07
Standard
J2936_201212
This SAE Recommended Practice provides for labeling guidelines at all levels of component, subsystem and system level architectures describing content, placement and durability requirements of specific unit throughout the total product life cycle from inception to reclamation.
HISTORICAL
2012-11-27
Standard
AMS2406M
This specification covers the requirements for electrodeposited hard chromium plate.
CURRENT
2012-11-19
Standard
J1211_201211
This document addresses robustness of electrical/electronic modules for use in automotive applications. Where practical, methods of extrinsic reliability detection and prevention will also be addressed. This document primarily deals with electrical/electronic modules (EEMs), but can easily be adapted for use on mechatronics, sensors, actuators and switches. EEM qualification is the main scope of this document. Other procedures addressing random failures are specifically addressed in the CPI (Component Process Interaction) section 10. This document is to be used within the context of the Zero Defect concept for component manufacturing and product use. It is recommended that the robustness of semiconductor devices and other components used in the EEM be assured using SAE J1879 OCT2007, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications.
CURRENT
2012-11-01
Standard
J661_201211
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
CURRENT
2012-11-01
Standard
J2357_201211
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements and design guidelines for electronic devices.
CURRENT
2012-10-30
Standard
AMS2280C
This specification establishes testing methods and maximum permissible limits for trace elements in nickel alloy castings.
HISTORICAL
2012-10-30
Standard
AMS2641B
This specification covers two types of refined hydrocarbon compounds in the form of liquids.
HISTORICAL
2012-10-15
Standard
J1772_201210
This SAE Recommended Practice covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in North America. This document defines a common EV/PHEV and supply equipment vehicle conductive charging method including operational requirements and the functional and dimensional requirements for the vehicle inlet and mating connector.
HISTORICAL
2012-10-08
Standard
AMS2773D
This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts made of cast nickel or cobalt alloys and of fabricated assemblies in which cast nickel or cobalt alloys are the primary structural components. It is not intended to provide requirements for heat treating operations that are a responsibility of the casting supplier in meeting the requirements of the casting commodity specification.
HISTORICAL
2012-10-08
Standard
AMS2774D
This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts made of wrought nickel or cobalt alloys, of raw materials during fabrication, and of fabricated assemblies in which wrought nickel or cobalt alloys are the primary structural components.
CURRENT
2012-09-24
Standard
AIR4057B
This SAE Aerospace Information Report (AIR) discusses the design choices and engineering trade-offs available to the system designer in the efficient selection and application of Last-Chance filters in contrast to main or primary system filters.
CURRENT
2012-09-20
Standard
AMS2451/9B
This specification covers the requirements for brush plating of zinc-nickel by electrodeposition.
CURRENT
2012-09-14
Standard
AMS2643E
This specification covers a procedure for revealing the macrostructure and microstructure of titanium alloys.
CURRENT
2012-09-13
Standard
AMS2728C
This specification establishes the requirements for heat treatment of wrought copper beryllium parts (See 1.2.2 and 8.2.1) by users or by their vendors or subcontractors.
HISTORICAL
2012-08-30
Standard
AS4461B
This standard is applicable to manual soldering and machine soldering processes utilizing controlled soldering devices, for electrical connections for wiring and cabling used in aerospace vehicles. Description of a component or device herein is not to be construed as authorizing the use of the component or device.
HISTORICAL
2012-08-16
Standard
AMS2368C
This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products except forgings and forging stock. It is applicable to the extent specified in a material specification.
CURRENT
2012-08-16
Standard
AS9103A
This standard is primarily intended to apply to new parts and products, but can also be applied to parts currently in production. The standard shall be applicable to all production processes, that influence the variation of KCs, as well as maintenance processes in which KCs are identified. It applies to assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product. It does not apply to lab-scale, pilot, or pre-production processes. However, particular management of some KCs might be required using other methods than those described in the standard, during these phases of a program, when required by the customer or deemed appropriate by the organization (e.g., Engineering department requirement).
CURRENT
2012-08-16
Standard
AS9131C
This standard defines the common nonconformance data definition and documentation that shall be exchanged between an internal/external supplier or sub-tier supplier, and the customer when informing about a nonconformity requiring formal decision. The requirements are applicable, partly or totally, when reporting a product nonconformity to the owner or operator, as user of the end item (e.g., engine, aircraft, spacecraft, helicopter), if specified by contract. The process of exchanging, coordinating, and approving nonconformance data varies with the multiple relationships and agreements among all parties concerned. The information provided by this standard forms guidelines for submitting and managing of data through accurate communication. The main objective is to provide the definition of a data set that can be integrated into any form of communication (e.g., electronic data interchange, submission of conventional paper forms).
CURRENT
2012-07-31
Standard
AS9003A
This standard includes selected quality system requirements from ISO 9001:2008[1] and AS9100:2009 applicable to noncomplex products and associated manufacturing processes. ISO 9001 text incorporated into this standard appears in standard font; while aviation, space, and defense industry additional requirements, definitions, and notes are presented in bold, italic text. The requirements of this standard are intended to be applied in whole, without any exclusions. Compliance with all corresponding AS9100 requirements is considered to meet/exceed compliance with the requirements of this standard. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence. The process approach described in ISO 9001 and AS9100 applies to this standard.
CURRENT
2012-07-27
Standard
AMS2750E
This specification covers pyrometric requirements for thermal processing equipment used for heat treatment. It covers temperature sensors, instrumentation, thermal processing equipment, system accuracy tests, and temperature uniformity surveys. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification(s).
CURRENT
2012-07-23
Standard
J1877_201207
This SAE Recommended Practice describes the basic content requirements, bar code specifications, and functional test specifications of the vehicle identification number (VIN) label. On the vehicle, the VIN label is to be mounted in a readily accessible location for use of a bar-code scanning device.
CURRENT
2012-07-23
Standard
AMS2407F
This specification covers requirements for electrodeposited porous chromium plate.
HISTORICAL
2012-07-23
Standard
AMS2430S
This specification covers the requirements for automatic shot peening of surfaces of parts by impingement of media, including metallic, glass, or ceramic shot.
CURRENT
2012-05-17
Standard
J1454_201205
This SAE Standard describes a laboratory test procedure for comparatively evaluating the durability and fatigue life qualities of a complete seat cushion by submitting the seating surface of the cushion to repetitive compressive and rotational loading with a simulated human buttocks.
HISTORICAL
2012-05-15
Standard
AMSP81728A
This specification covers the requirements for electrodeposited tin-lead plating intended for use as a coating for corrosion protection and as a base for soldering.
CURRENT
2012-05-07
Standard
JA1000/1_201205
The importance of reliability in design engineering has significantly grown since the early 1960’s. Competition has been a primary driver in this growth. The three realities of competition today are: world class quality and reliability, cost-effectiveness, and fast time-to-market. Formerly, companies could effectively compete if they could achieve at least two of these features in their products and product development processes, often at the expense of the third. However, customers today, whether military, aerospace, or commercial, have been sensitized to a higher level of expectation and demand products that are highly reliable, yet affordable. Product development practices are shifting in response to this higher level of expectation. Today, there is seldom time, or necessary resources to extensively test, analyze, and fix to achieve high quality and reliability.
2012-05-07
WIP Standard
J4001
SAE J4001 provides instruction for evaluating levels of compliance to SAE J4000. Component text (Sections 4 to 9) from SAE J4000 is included for convenience during the evaluation process. Applicable definitions and references are contained in SAE J4000. SAE J4000 tests lean implementation within a manufacturing organization and includes those areas of direct overlap with the organization's suppliers and customers. If applied to each consecutive organizational link, an enterprise level evaluation can be made. SAE J4001 relates the following approximate topic percentages to the implementation process as a whole: Element 4 Management/Trust 25% Element 5 People 25% Element 6 Information Element 7 Supplier/Organization/Customer 25% (combined) Element 8 Product Element 9 Process/Flow 25% SAE J4001 is to be applied on a specific component basis. Each of the fifty-two components tests part of, one, or multiples of the specific requirements of lean implementation.
Viewing 211 to 240 of 1425