Criteria

Text:
Content:
Display:

Results

Viewing 181 to 1 of 1
HISTORICAL
2013-05-29
Standard
AMS2629C
This specification covers a mixture of liquid hydrocarbons and soluble additives.
CURRENT
2013-05-29
Standard
AMS2665H
This specification covers the engineering requirements for producing brazed joints in parts fabricated from steels, iron alloys, nickel alloys, cobalt alloys, and copper alloys by use of silver alloys, and the properties of such joints.
CURRENT
2013-05-23
Standard
J2024_201305
This SAE Information Report establishes a minimum level of uniform recipes for contaminants which may be used when durability testing pneumatic components to obtain additional information on how a device may perform under more true-to-life operating conditions. This type of contamination testing, however, is not meant to replace the type of performance testing described in SAE J1409 and SAE J1410. Durability testing in the presence of contamination, however, will yield results more reflective of actual in-service field conditions and provide an additional evaluation of pneumatic devices. While the contaminant supply rate and other test criteria of the device being tested must be set by the device manufacturer or user, the items covered in this document will be:
CURRENT
2013-05-16
Standard
JA6097_201305
SAE JA6097 (“Using a System Reliability Model to Optimize Maintenance”) shows how to determine which maintenance to perform on a system when that system requires corrective maintenance to achieve the lowest long-term operating cost. While this document may focus on applications to Jet Engines and Aircraft, this methodology could be applied to nearly any type of system. However, it would be most effective for systems that are tightly integrated, where a failure in any part of the system causes the entire system to go off-line, and the process of accessing a failed component can require additional maintenance on other unrelated components.
CURRENT
2013-05-01
Standard
TAHB0009
This handbook provides "how to" guidance to industry and government for the reliability Activities and Methods contained in ANSI/GEIA-STD-0009 for developing reliable products and systems, successfully demonstrating them during test and evaluation, and sustaining them throughout the system/product life cycle. ANSI/GEIA-STD-0009 requires the developers and customer/users working as a team to plan and implement a reliability program that provides systems/products that satisfy the user's requirements and expectations using a systems engineering approach. The four Objectives of ANSI/GEIA-STD-0009 are listed below: Objective 1: Understand Customer/User Requirements and constraints. The team (developer, customer, and user), includes the Activities necessary to ensure that the user's requirements and product needs are fully understood and defined, so that a comprehensive design specification and Reliability Program Plan are generated. Objective 2: Design and redesign for reliability.
CURRENT
2013-03-26
Standard
J3014_201303
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
2013-03-25
WIP Standard
AMS2466C
This specification covers the requirements for a hard anodic coating on magnesium alloys. This coating has been used typically to provide corrosion resistance and abrasion resistance to cast magnesium alloys, but usage is not limited to such applications.
CURRENT
2013-03-21
Standard
AMS2516E
This specification establishes the engineering requirements for producing thick coatings of polytetrafluoroethylene (PTFE) resin on parts and the properties of such coatings.
CURRENT
2013-03-05
Standard
J2886_201303
SAE J2886 Design Review Based on Failure Modes (DRBFM) Recommended Practice is intended for Automotive and Non-Automotive applications. It describes the basic principles and processes of DRBFM including planning, preparation, change point FMEA, design reviews, decisions based on actions completed, and feedback loops to other processes, such as design, validation and process guidelines (Appendix B - DRBFM Process Map). The intent of each fundamental step of the DRBFM methodology is presented. It is intended for use by organizations whose product development processes currently (or intend to) use Failure Mode & Effects Analysis (FMEA) or DRBFM as a tool for assessing the potential risk and reliability of system elements (product or process) or as part of their product improvement processes.
CURRENT
2013-03-05
Standard
J2999_201303
This SAE Standard provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies. Lamps can be evaluated using the method described in SAE J3333; however, no lamp is subjected to both methods.
CURRENT
2013-02-20
Standard
AMS2402K
This specification covers the requirements for electrodeposited zinc plating.
CURRENT
2013-02-15
Standard
AMS2401J
This specification covers the engineering requirements for cadmium deposited on ferrous metals.
CURRENT
2013-02-12
Standard
AMS2400X
This specification covers the requirements for electrodeposited cadmium on metal parts.
CURRENT
2013-02-11
Standard
AMS2771E
This specification covers the engineering requirements for heat treatment of aluminum alloy castings and for parts machined from castings.
CURRENT
2013-02-11
Standard
AMS2773E
This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts made of cast nickel or cobalt alloys and of fabricated assemblies in which cast nickel or cobalt alloys are the primary structural components. It is not intended to provide requirements for heat treating operations that are a responsibility of the casting supplier in meeting the requirements of the casting commodity specification.
CURRENT
2013-02-11
Standard
AMS2315G
This specification covers two methods for determining the percentage of delta ferrite in steels and other iron alloys. When applicable, this specification will be invoked by the material specification.
CURRENT
2013-02-08
Standard
AMS2675H
This specification covers the requirements forproducing brazed joints in parts made of steels, iron alloys, nickel alloys, and cobalt alloys by use of nickel alloy filler metal.
CURRENT
2013-02-07
Standard
AMS2667G
This specification covers requirements for producing brazed joints in parts fabricated from corrosion and heat resistant steels, carbon or low-alloy steels, or copper alloys, and the properties of such joints.
CURRENT
2013-02-07
Standard
AMS2431/7B
The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS2431.
CURRENT
2013-02-06
Standard
AMS2432D
This specification establishes the requirements for computer monitored shot peening of part surfaces by impingement of media, including metallic, glass, or ceramic shot. Computer monitored peening is intended to provide a method of process observation, traceability, and response for all process input settings, in real time, during the entire peening process to ensure with objective evidence, the desired process outputs. Shot peening in accordance with AMS2432 meets or exceeds the requirements of AMS2430.
CURRENT
2013-01-28
Standard
AMS2694C
This specification defines the requirements for in-process correction of foundry discontinuities by manual welding of castings.
CURRENT
2013-01-25
Standard
AMS2515G
This specification establishes the engineering requirements for producing thin coatings of polytetrafluoroethylene (PTFE) resin on parts and the properties of such coatings.
CURRENT
2013-01-17
Standard
AMS2281B
This specification establishes maximum permissible limits for elements not normally specified but which may occur in trace amounts in wrought nickel, cobalt, and iron alloy products.
CURRENT
2013-01-12
Standard
AMS2526D
This specification covers requirements for a coating consisting of finely-powdered molybdenum disulfide in a heat-resistant inorganic binder applied to parts.
CURRENT
2012-12-17
Standard
AMS2425F
This specification covers the requirements for gold deposited on metal surfaces and the properties of the deposit.
CURRENT
2012-12-07
Standard
J2936_201212
This SAE Recommended Practice provides for labeling guidelines at all levels of component, subsystem and system level architectures describing content, placement and durability requirements of specific unit throughout the total product life cycle from inception to reclamation.
HISTORICAL
2012-11-27
Standard
AMS2406M
This specification covers the requirements for electrodeposited hard chromium plate.
CURRENT
2012-11-19
Standard
J1211_201211
This document addresses robustness of electrical/electronic modules for use in automotive applications. Where practical, methods of extrinsic reliability detection and prevention will also be addressed. This document primarily deals with electrical/electronic modules (EEMs), but can easily be adapted for use on mechatronics, sensors, actuators and switches. EEM qualification is the main scope of this document. Other procedures addressing random failures are specifically addressed in the CPI (Component Process Interaction) section 10. This document is to be used within the context of the Zero Defect concept for component manufacturing and product use. It is recommended that the robustness of semiconductor devices and other components used in the EEM be assured using SAE J1879 OCT2007, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications.
Viewing 181 to 1 of 1