Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 1443
2015-09-22
WIP Standard
AMS2416M
This specification covers the engineering requirements for an electrodeposit of cadmium into an electrodeposit of nickel on carbon, low-alloy, and corrosion-resistant steels.
2015-09-22
WIP Standard
AMS2700F
This specification covers the requirements for a process to assure removal of free iron or other less noble contaminants from the surfaces of corrosion resistant steel parts.
CURRENT
2015-08-27
Standard
J2654_201508
Hardness measurements are used as a quality control check of the consistency of formulation and processing of brake linings. This hardness method is nondestructive. NOTE—This method is not a measure of friction level. The hardness and the range of hardness are characteristic of each formulation; therefore, the acceptable values and ranges must be established for each formulation and may be affected by processing. NOTE—The hardness of sintered powder metal lining is usually determined with Rockwell superficial hardness equipment. (See ASTM B 347)
CURRENT
2015-08-01
Standard
EIA738
This document proivdes the guidelines for the utilization of Cpk as a monitor of process performance. This document: -defines the process capability index (Cpk), -outlines some general methods for estimating Cpk, -describes acceptable methods of reporting Cpk, -discusses the advantages, disadvantages, and requirements for some potential applications of Cpk, -addresses the use of similar methods of assessing quality improvement, and -provides some perspective on the value of Cpk and similar techniques. Application of the guidelines in this document should allow businesses to use Cpk or similar techniques to effectively monitor one aspect of quality improvement and to promote strong customer/supplier relationships.
2015-07-24
WIP Standard
AS13005
The project will cover three areas (step 1 New Production): define a standard approach for the internal audit system used by the supplier to ensure that it has the correct scope and effectiveness the effectiveness of AS9100 and Nadcap third party assessment define a standard/common approach for the audit of supplier´s production and process to be used by engine manufacturers, suppliers and the sub tiers based on result/confidence in 1) and 2)
CURRENT
2015-07-01
Standard
EIA681
It is the purpose of this document to provide guidance for companies and registrars to achieve a consistent assessment of a producers compliance to the requirements of Process Certification (EIA-599). In addition , a technique is provided as an option for the assessment of a producer's level of quality system maturity.
CURRENT
2015-07-01
Standard
EIA584
Conventional attribute sampling plans based upon nonzero acceptance numbers are no longer desirable. In addition, emphasis is now placed on the quality level that is received by the customer. This relates directly to the Lot Tolerance Percent Defective (LTPD) value or the Limiting Quality Protection of MIL-STD-105. Measuring quality levels in precent nonconforming, although not incorrect, has been replaced with quality levels measured in parts per million (PPM). As a result, this standard addresses the need for sampling plans that can augment MIL-STD-105, are based upon a zero acceptance number, and address quality (nonconformance) levels in the parts per million range. This document does not address minor nonconformances, which are defined as nonconformances that are not likely to reduce materially the usability of the unit of product for its intended purpose.
CURRENT
2015-06-12
Standard
AS9014A
These requirements are applicable to IAQG sector schemes when making use of ABs, CRBs and their auditors, for the assessment and certification/registration of supplier quality systems in accordance with the requirements of this document. The quality management system standard used by the CRB shall be 9100/9110/9120, as appropriate to the supplier’s activities. It shall be applied to the supplier’s complete Quality System that covers aerospace products. Sectors may use these requirements for other standards. IAQG members have committed to recognize the equivalence of certification/registration of a suppliers quality management system to either of the AS, EN or JISQ/SJAC standards. This AS provides the approval process for Auditor Authentication Bodies (AAB), training course providers, trainers and auditors who meet the requirements of AIR5493 and outlines the America’s sector specific process to implement AS9104. This document is created to be in conformance with AS9104.
CURRENT
2015-05-19
Standard
AS9132B
This standard defines uniform quality and technical requirements relative to metallic parts marking performed using "data matrix symbology" within the aviation, space, and defense industry. ISO/IEC 16022 specifies general requirements (e.g., data character encodation, error correction rules, decoding algorithm). In addition to ISO/IEC 16022 specification, part identification with such symbology is subject to the requirements in this standard to ensure electronic reading of the symbol. The marking processes covered by this standard are as follows: Dot Peening Laser Electro-Chemical Etching Further marking processes will be included, if required. Unless specified otherwise in the contractual business relationship, the company responsible for the design of the part shall determine the location of the data matrix marking. Symbol position should allow optimum illumination from all sides for readability. This standard does not specify information to be encoded.
CURRENT
2015-05-07
Standard
ARP597E
This document recommends supplementary design criteria to enhance endurance and reliability of transport aircraft wheels and brakes.
2015-04-10
WIP Standard
AMS2477B
This specification covers the requirements for a low-electrical-resistance chemical conversion coating on aluminum and aluminum alloy parts.
2015-04-10
WIP Standard
AMS2680D
This specification defines the procedures and requirements for joining metals and alloys using the electron-beam welding process.
2015-04-10
WIP Standard
AMS2410L
This specification covers the engineering requirements for electrodeposition of silver on other metals, usually with a nickel strike between the basis metal and the silver.
2015-04-10
WIP Standard
AMS2546A
This specification covers the requirements for computer controlled laser peening of metal part surfaces to induce residual compressive stresses at and beneath the surface.
2015-04-10
WIP Standard
AMS2424G
This specification covers the engineering requirements for electrodeposition of a low-stressed nickel and the properties of the deposit.
CURRENT
2015-03-17
Standard
AS13002
This document covers the process to be applied to design characteristics (as defined in AS9102), parts or inspection processes as defined by the purchaser. Design characteristics not included within the scope include electronic, electromechanical or mechanical systems where alternative means of acceptance are approved such as through acceptance test procedures (ATPs). This document does not define processes for identifying or communicating the classification of the parts or design characteristics. This document does not define the procedure to qualify a supplier to undertake these requirements. It is expected that each purchaser will have a procedure to manage the flow-down of these requirements. This document applies to suppliers that demonstrate adequate proficiency in applicable process control methods as determined by the purchaser.
CURRENT
2015-03-12
Standard
AS9016A
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications must be approved prior to implementation.
2015-02-24
WIP Standard
AS9147
Parts that are declared as unsalvageable are difficult to trace from the workshop to the destruction/recycling area
2015-02-13
WIP Standard
ARP4955B
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances.
CURRENT
2015-02-05
Standard
AS13003
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance).
2015-01-23
WIP Standard
AMS2801C
This specification covers the engineering requirements for heat treatment by part fabricators (users) or their vendors or subcontractors, of parts (See 1.1.2) made from the following titanium alloys: Commercially Pure 6Al-4V(ELI) 3Al-8V-6Cr-4Mo-4Zr 3Al-2.5V 6Al-6V-2Sn 13V-11Cr-3Al 5AI-2.5Sn 6Al-2Sn-4Zr-2Mo 10V-2Fe-3Al 8Al-1Mo-1V 6AI-2Sn-4Zr-6Mo 15V-3Cr-3Al-3Sn
CURRENT
2014-10-30
Standard
AS9116
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation.
2014-10-20
WIP Standard
AS13004
Process Flow Description, PFMEA and Control Plans
2014-10-16
WIP Standard
AMS2630D
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.50 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
CURRENT
2014-10-01
Standard
CMB6_5
CURRENT
2014-10-01
Standard
CMB7_1
The scope of this bulletin is to provide guidance on the use of current and future technologies for the electronic interchange of CM data.
CURRENT
2014-10-01
Standard
CMB6_6
CURRENT
2014-09-30
Standard
J2932_201409
This document provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability and environmental performance when tested according to SAE J2902.
Viewing 121 to 150 of 1443