Criteria

Text:
Content:
Display:

Results

Viewing 61 to 90 of 1425
CURRENT
2016-06-27
Standard
ARP9005A
This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous.
CURRENT
2016-06-20
Standard
AMS2370L
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock.
CURRENT
2016-06-17
Standard
EIA599A
This Standard is applicable to suppliers of electronic components, assemblies, equipment and related materials. This standard establishes the general requirements to achieve a certified process. The use of this standard is intended for any manufacturing or service company whose goal is to achieve customer satisfaction through continuous improvement.
CURRENT
2016-06-17
Standard
EIA765A
This index is presented to provide a quick reference of international and national quality standards and publications that support general quality system elements. This reference is a list of quality standards a company may with to consider when implementing or improving their quality system.
CURRENT
2016-06-17
Standard
RB4A
A guide for the use by companies contracting for design of electronic products with the Department of Defense (DOD) and other government agencies. This Bulletin present concepts and techniques for quantifying electronic equipment reliability. The techniques are responsive to the requirements of various branches of the Department of Defense and are also useful with regard to other Government agencies (e.g., NASA).
CURRENT
2016-06-16
Standard
EIAQAB7
This document has been formulated as a suggested guide in assisting EIA Engineering Department Panels and JEDEC Councils in cooperating with the Defense Department and other Federal agencies in the preparation of suggested reliability requirements for various types of electronic products as part of a program designed to enhance the reliability of defense and related equipment. The document is to be followed merely as a guide and is not intended to limit technical groups in the consideration of the factors to be taken into account in the development of reliability specifications for recommendation to the Government.
CURRENT
2016-05-31
Standard
CRB2
This paper originated with a software quality panel workshop at the EIA Computer Resources Workshop. The panel group initially focused on requirements for nondeliverable software. It was felt that the requirements for deliverable software were well covered by Department of Defense standards but non-deliverable software issues were not adequately covered. After much discussion, including attempts to define nondeliverable by examples of software types, a surprising unanimous conclusion was reached by the participants. That is: the states of "deliverable" and "non-deliverable" had no bearing on the quality of the software, and thereby also had no bearing on the quality assurance requirements that should be applied for that software. Rather, the only rational application of quality assurance was primarily dependent on the impact that the software had, or could have, on the end product (¡.e. the ultimate mission).
CURRENT
2016-05-31
Standard
EIA554_1
This standard is intended to provide a uniform method of calculating an estimate of the proportion nonconforming in finished components and to provide a standardized definition of the quality index referred to as Average Outgoing Quality (AOQ). The method used here is primarily directed at components whose production or procured volume is large enough, during some predefined sampling period, to give statistically meaningful information.
CURRENT
2016-05-31
Standard
EIA555
This Specification covers a statistical sampling plan for lot inspection by attributes. It verifies that the customer's specified quality level (SQL) is not being exceeded. The estimate of fraction nonconforming determined by EIA Interim Standard No. EIA-554 is used to select the optimum sample plan for verifying that a given lot meets the specified quality level (SQL).
CURRENT
2016-05-31
Standard
EIA554_2
This standard is intended to provide a uniform method of determining proportion nonconforming in finished components and to provide a standardized definition of the quality index referred to as PPM. The method used here is primarily directed at components whose production or procured volume is large enough, during some predefined sampling period, to give statistically meaningful information.
2016-05-13
WIP Standard
AS13007
This standard establishes methods to be used by organizations when achieving compliance to customer and purchaser requirements in supplier management related activities. The intent of standardization is to increase supply chain efficiency and reduce non-compliance through alignment of customer requirements.
CURRENT
2016-04-20
Standard
AS9133A
This standard defines a system for the qualification of standard products for aviation, space, and defense applications. It defines the principles that shall be adhered to when carrying out product qualification; applied in conjunction with the rules and procedures of the CA. The system enables the CA to confirm compliance is achieved and maintained, in accordance with the requirements of its product definition and associated controlling technical specifications by an Original Component Manufacturer (OCM) of standard products. This standard requires an OCM that has been granted product qualification approval to ensure applicable approvals are maintained and renewed in accordance with the CA’s quality system for that qualified product. OCMs and OCM designated Value Added Distributors (VADs) requesting product qualification to this standard, shall as a prerequisite, maintain 9100 standard quality management system certification approval.
2016-04-18
WIP Standard
AS13001A
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements however this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
2016-04-11
WIP Standard
J2816
The Physics-of-Failure (PoF) is a science-based approach to reliability that uses modeling and simulation to design-in reliability. This approach models the root causes of failures such as fatigue, fracture, wear, and corrosion. Computer-Aided Design (CAD) tools have been developed to address various loads, stresses, failure mechanisms and sites. PoF uses knowledge of basic failure processes to prevent failures through robust design and manufacturing practices, and aims to: - Design-in reliability up front; - Eliminate failures prior to testing; - Increase fielded reliability; - Promote rapid, cost effective deployment of Health and Usage Monitoring Systems (HUMS); - Improve diagnostic and prognostic techniques and processes; and, - Decrease operational and support costs. This guide provides a high level overview of the methodology, process and advantages to performing a PoF assessment.
CURRENT
2016-03-29
Standard
AS9117
This standard specifies requirements for DPRV to establish common product/service requirements for use at all levels of the supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to their supplier (reference 9100 and 9110 standards); to perform product acceptance on their behalf. The delegating organization shall use this standard as the baseline for establishing a DPRV process, although they may include additional contract requirements to meet their specific needs.
2016-03-22
WIP Standard
AMS2451/6B
This specification establishes the requirements for brush plating of copper by electrodeposition.
2016-03-22
WIP Standard
AMS2451/9C
This specification covers the requirements for brush plating of zinc-nickel by electrodeposition.
2016-03-22
WIP Standard
AMS2451/10B
This specification covers the requirements for brush plating of tin-zinc by electrodeposition.
2016-03-22
WIP Standard
AMS2451/12A
This specification covers the engineering requirements and process for brush plating of tin by electrodeposition. It shall be used, in conjunction with AMS 2451, for general-purpose tin deposits.
2016-03-22
WIP Standard
AMS2451/11B
This specification covers the requirements for brush plating of cobalt by electrodeposition.
2016-03-22
WIP Standard
AMS2451/13A
This specification covers the engineering requirements and process for brush plating of silver by electrodeposition. It shall be used, in conjunction with AMS 2451, for silver deposits.
2016-03-22
WIP Standard
AMS2451D
This specification and its supplementary detail specifications establish the requirements for electrodeposition of metals by brush plating.
2016-03-22
WIP Standard
AMS2451/2B
This specification covers the requirements and process controls for brush plating of hard, low stress nickel by electrodeposition.
2016-03-22
WIP Standard
AMS2753D
This specification covers the requirements for an epsilon-iron nitride case on ferrous parts produced by immersion in a low-temperature, agitated, fused salt bath.
2016-03-22
WIP Standard
AMS2615G
This specification provides requirements and procedures for hydraulic-pressure leak testing of parts.
2016-03-22
WIP Standard
AMS2757C
This specification covers the engineering requirements for producing a continuous thin epsilon iron carbonitride compound layer on parts by means of a gaseous, low-temperature process, and properties of the case.
CURRENT
2016-03-11
Standard
J1597_201603
This SAE Recommended Practice is applicable to all liquid-to-gas, liquid-to-liquid, gas-to-gas, and gas-to-liquid heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine durability characteristics of the heat exchanger under pressure cycling.
2016-03-09
WIP Standard
ARP5021B
This document provides guidance for oxygen cylinder installation on commercial aircraft based on rules and methods practiced in aerospace industry and applicable in other associations. It covers considerations for oxygen systems from beginning of project phase up to production, maintenance, and servicing. The document is focused on requirements regarding DOT approved oxygen cylinders. However, its basic rules may also be applicable to new development pertaining to use of such equipment in an oxygen environment. For information regarding oxygen cylinders itself, reference should be made to AIR825/12 also.
CURRENT
2016-02-24
Standard
GEIAHB0005_1A
This handbook is designed to assist a program in assuring the performance, reliability, airworthiness, safety, and certifiability of product(s), in accordance with GEIA-STD-0005-1, “Performance Standard for Aerospace and High Performance Electronic Systems Containing Pb-free Solder”. Please note that the program manager, and managers of systems engineering, Supply Chain and Quality Assurance (along with their respective organizations), and the appropriate enterprise authority need to work together in ensuring that all impacts of Pb-free technology insertion are understood and risks mitigated accordingly. Herein “program management (or manager), supplier chain management (or manager), quality assurance management (or manager) and systems engineering management (or manager) and/or the appropriate enterprise authority” shall be defined as “responsible manager” throughout the remaining document (see Section 3, Terms and Definitions).
CURRENT
2016-02-04
Standard
J1542_201602
This SAE Recommended Practice is applicable to all liquid-to-air, liquid-to-liquid, air-to-liquid, and air-to-air heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine durability characteristics of the heat exchanger under thermal cycling.
Viewing 61 to 90 of 1425