Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 1324
2017-05-19
WIP Standard
ARP9009A
This Aerospace Recommended Practice is recommended for use by all contracting organizations that externally procure products, parts and services from other organizations. All requirements of this ARP are typically generic and are intended to be applicable to all organizations, regardless of type, size and product provided.
2017-05-02
WIP Standard
AMS2223J
This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy seamless tubing ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" is used to apply only to the higher figure of a specified range.
CURRENT
2017-04-26
Standard
AS9146
This standard defines FOD Prevention Program requirements for organizations that design, develop, and provide aviation, space, and defense products and services; and by organizations providing post-delivery support, including the provision of maintenance, spare parts, or materials for their own products and services. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer, and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
2017-04-20
WIP Standard
AS9104/1A
These requirements are applicable to IAQG global sectors when utilizing Aerospace Industry Controlled Other Party (ICOP) schemes for the assessment and certidication of supplier quality systems in accordance with the requirements AS/EN/SJAC 9104.
2017-04-20
WIP Standard
AS9103B
This standard is primarily intended to apply to new parts and products, but can also be applied to parts currently in production. The standard shall be applicable to all production processes, that influence the variation of KCs, as well as maintenance processes in which KCs are identified. It applies to assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product. It does not apply to lab-scale, pilot, or pre-production processes. However, particular management of some KCs might be required using other methods than those described in the standard, during these phases of a program, when required by the customer or deemed appropriate by the organization (e.g., Engineering department requirement).
2017-04-19
WIP Standard
AMS2429E
This specification covers the requirements for electrodeposited bronze plate and subsequent removal.
2017-04-19
WIP Standard
AMS2420E
This specification covers the requirements for preparation of aluminum and aluminum alloys for soldering by zinc immersion pre-treatment followed by copper plating and tin or tin-zinc alloy plating.
2017-04-19
WIP Standard
AMS2487B
This specification describes the engineering requirements for producing an electrically-insulating, non-powdery anodic coating on titanium and titanium alloys and the properties of such coatings.
2017-04-19
WIP Standard
AMS2673F
This specification covers the requirements for producing brazed joints of aluminum and aluminum alloys by immersion in a molten flux bath.
2017-04-19
WIP Standard
AMS2672H
This specification covers the requirements for producing brazed joints on aluminum and alumiinum alloys by torch or furnace brazing.
2017-04-19
WIP Standard
AMS2819C
This specification covers the procedures for identification and marking of bare welding wire by a color code system and marking of spools.
2017-04-19
WIP Standard
AMS2447E
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
2017-04-19
WIP Standard
AMS2442B
This specification establishes acceptance criteria for discontinuities revealed by magnetic particle inspection of parts made from wrought, ferromagnetic materials.
2017-04-04
WIP Standard
AMS2249H
This specification defines limits of variation for determining acceptability of the composition of cast or wrought titanium and titanium alloy parts and material acquired from a producer. When specifically referenced in the material specification, the purchaser may apply check analysis limits to determine the acceptability of parts and materials at purchaser final acceptance or verification testing operation. Check analysis limits are not for producers use at producer’s acceptance testing. Composition of parts and materials must conform to the limits of the material specification. Check limits are not permitted for ladle or ingot analysis.
CURRENT
2017-03-28
Standard
ARP9162A
The focus of Operator Self-Verification is on traditional manufacturing operations, and applications can be made wherever traditional inspection is employed. The practices recommended in this document are intended to identify the basic elements and provide a “guideline” for structuring Operator Self-Verification programs within the aerospace industry; applicable to producers of commercial and military aircraft and weapons platforms, space vehicles, and all related hardware, software, electronics, engines and composite components. Operator Self-Verification programs are applied to improve the overall efficiency and product quality of processes considered mature, as judged by the implementing organization. Operator Self-Verification programs are not stand-alone processes, but augment existing quality management systems.
2017-02-16
WIP Standard
AMS2745B
This specification defines the requirements for locally hardening steel parts by the induction hardening method.
CURRENT
2017-02-10
Standard
AMSSTD595A
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
CURRENT
2017-02-08
Standard
AMS2629E
This specification covers a mixture of liquid hydrocarbons and soluble additives.
CURRENT
2017-02-07
Standard
AMS2503G
This specification covers the engineering requirements for finishing aircraft parts and assemblies with a black enamel.
CURRENT
2017-02-02
Standard
J379_201702
Hardness measurements are used as a quality control check of the consistency of formulation and processing of brake linings. Gogan hardness is nondestructive (the penetrator causes shallow surface deformation.). Gogan hardness method alone does not show anything about a lining’s ability to develop friction or to resist fade when used as a friction element in brakes. The hardness and the range of hardness are peculiar to each formulation, thickness, and contour; therefore, the acceptable values and ranges must be established for each formulation and part configuration by the manufacturer.
CURRENT
2017-02-02
Standard
J380_201702
Specific gravity is a nondestructive test used as a quality control check of the consistency of formulation and processing of brake lining. The specific gravity and the range of specific gravity are peculiar to each formulation and, therefore, the acceptable values or range must be established for each formulation by the manufacturer. Specific gravity alone shows nothing about a materials in use performance. The specific gravity of sintered metal powder friction materials, particularly those which have steel backing members, is usually determined somewhat differently. Reference ASTM B 376.
CURRENT
2016-11-08
Standard
AS9162
This document identifies the basic elements and provides a standard for structuring operator self-verification programs within the aviation, space, and defense industry for producers of commercial and military aircraft and weapons platforms, space vehicles, and all related hardware, software, electronics, engines, and composite components. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2016-11-08
Standard
AS9145
This standard establishes requirements for performing and documenting APQP and PPAP. APQP begins with conceptual product needs and extends through product definition, production planning, product and process validation (i.e., PPAP), product use, and post-delivery service. This standard integrates and collaborates with the requirements of the 9100, 9102, 9103, and 9110 standards. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2016-11-08
Standard
ARP9136
The objective of any organization, as part of continual improvement, is to reduce the number of issues (i.e., undesirable conditions, defects, failures) and to minimize their impact on quality, delivery performance, and cost. This includes having processes in place to detect and eradicate significant and recurrent issues, which implies having well identified problems, a common understanding of their impact and associated root causes, and having defined and implemented adequate actions so that these problems, including similar issues will not happen again.
CURRENT
2016-11-04
Standard
AS9110C
This standard includes ISO 9001:20152 quality management system requirements and specifies additional civil and military aviation maintenance and continuing airworthiness industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2016-11-01
Standard
AS9120B
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2016-10-31
Standard
AS9101F_PTBR
Para garantir a satisfação dos clientes as organizações de defesa, aviação e aeroespacial devem fornecer e melhorar continuamente produtos e serviços, seguros e confiáveis, que atendam ou excedam os requisitos legais e regulamentares aplicáveis dos clientes. A globalização da indústria e a diversidade resultante das necessidades e expectativas regionais e nacionais têm dificultado este objetivo. As organizações têm o desafio de comprar produtos e serviços de fornecedores em todo o mundo, em todos os níveis da cadeia de suprimento. Os fornecedores têm o desafio de fornecer produtos e serviços a vários clientes com diferentes necessidades e expectativas de qualidade.
2016-10-31
WIP Standard
AS13008
This document covers the process to be applied by a supplier of the aero-engine supply chain to ask for audit frequency reduction. It defines the criterias that the supplier should meet to be eligible.
CURRENT
2016-10-31
Standard
AS9101F
This standard defines requirements for the preparation and execution of the audit process. In addition, it defines the content and composition for the audit reporting of conformity and process effectiveness to the 9100-series standards, the organization's QMS documentation, and customer and statutory/regulatory requirements. The requirements in this standard are additions or represent changes to the requirements and guidelines in the standards for conformity assessment, auditing, and certification as published by ISO/IEC (i.e., ISO/IEC 17000, ISO/IEC 17021-1). When there is conflict with these standards, the requirements of the 9101 standard shall take precedence.
2016-10-21
WIP Standard
AMS2810H
This specification provides requirements for the identification and packaging of sheet, strip, extrusions, and molded parts made of natural rubber, synthetic rubber, reclaimed rubber, and combinations of the above with other materials such as asbestos, cork, and fabrics. AMS2817 covers preferred requirements for identification and packaging of preformed packings.
Viewing 1 to 30 of 1324

Filter

  • Standard
    1324