Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 1246
2016-08-12
Standard
AS9015A
This SAE Aerospace Standard (AS) further defines the requirements for a delegation process identified in Aerospace Quality Management System (AQMS) standards (i.e., AS9100, AS9110, AS9120). This standard establishes minimum requirements for the delegation of product verification to an organization's suppliers; outlining requirements for the initial delegation (qualification/selection), maintenance, and removal/withdrawal of delegations.
2016-08-03
WIP Standard
AMS2449A
This specification covers engineering requirements for the grinding of tungsten carbide High Velocity Oxygen/Fuel (HVOF) thermal spray coatings applied to high strength steels (220 ksi and above). This process has been used typically to grind tungsten carbide HVOF coatings applied in accordance with AMS 2447 or AMS 2448 to high strength steels for applications requiring wear, heat, and corrosion resistance or dimensional restoration, such as aircraft landing gear components, However, usage is not limited to such applications. This process specification does not cover superfinishing of HVOF applied coatings.
2016-06-27
Standard
ARP9005A
General: This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous. Application: The guidelines in this ARP apply to non-deliverable software that: - directly relates to design, manufacture, inspection, test or calibration of a deliverable product, and - directly affects the configuration, conformity or quality of a deliverable product.
2016-06-20
Standard
AMS2370L
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock.
2016-06-17
Standard
EIA765A
This index is presented to provide a quick reference of international and national quality standards and publications that support general quality system elements. This reference is a list of quality standards a company may with to consider when implementing or improving their quality system.
2016-06-17
Standard
EIA599A
This Standard is applicable to suppliers of electronic components, assemblies, equipment and related materials. This standard establishes the general requirements to achieve a certified process. The use of this standard is intended for any manufacturing or service company whose goal is to achieve customer satisfaction through continuous improvement.
2016-06-17
Standard
RB4A
A guide for the use by companies contracting for design of electronic products with the Department of Defense (DOD) and other government agencies. This Bulletin present concepts and techniques for quantifying electronic equipment reliability. The techniques are responsive to the requirements of various branches of the Department of Defense and are also useful with regard to other Government agencies (e.g., NASA).
2016-06-16
Standard
EIAQAB7
This document has been formulated as a suggested guide in assisting EIA Engineering Department Panels and JEDEC Councils in cooperating with the Defense Department and other Federal agencies in the preparation of suggested reliability requirements for various types of electronic products as part of a program designed to enhance the reliability of defense and related equipment. The document is to be followed merely as a guide and is not intended to limit technical groups in the consideration of the factors to be taken into account in the development of reliability specifications for recommendation to the Government.
2016-05-31
Standard
EIA738
This document proivdes the guidelines for the utilization of Cpk as a monitor of process performance. This document: -defines the process capability index (Cpk), -outlines some general methods for estimating Cpk, -describes acceptable methods of reporting Cpk, -discusses the advantages, disadvantages, and requirements for some potential applications of Cpk, -addresses the use of similar methods of assessing quality improvement, and -provides some perspective on the value of Cpk and similar techniques. Application of the guidelines in this document should allow businesses to use Cpk or similar techniques to effectively monitor one aspect of quality improvement and to promote strong customer/supplier relationships.
2016-05-31
Standard
CRB2
This paper originated with a software quality panel workshop at the EIA Computer Resources Workshop. The panel group initially focused on requirements for nondeliverable software. It was felt that the requirements for deliverable software were well covered by Department of Defense standards but non-deliverable software issues were not adequately covered. After much discussion, including attempts to define nondeliverable by examples of software types, a surprising unanimous conclusion was reached by the participants. That is: the states of "deliverable" and "non-deliverable" had no bearing on the quality of the software, and thereby also had no bearing on the quality assurance requirements that should be applied for that software. Rather, the only rational application of quality assurance was primarily dependent on the impact that the software had, or could have, on the end product (¡.e. the ultimate mission).
2016-05-31
Standard
EIA554_2
This standard is intended to provide a uniform method of determining proportion nonconforming in finished components and to provide a standardized definition of the quality index referred to as PPM. The method used here is primarily directed at components whose production or procured volume is large enough, during some predefined sampling period, to give statistically meaningful information.
2016-05-31
Standard
EIA554_1
This standard is intended to provide a uniform method of calculating an estimate of the proportion nonconforming in finished components and to provide a standardized definition of the quality index referred to as Average Outgoing Quality (AOQ). The method used here is primarily directed at components whose production or procured volume is large enough, during some predefined sampling period, to give statistically meaningful information.
2016-05-31
Standard
EIA555
This Specification covers a statistical sampling plan for lot inspection by attributes. It verifies that the customer's specified quality level (SQL) is not being exceeded. The estimate of fraction nonconforming determined by EIA Interim Standard No. EIA-554 is used to select the optimum sample plan for verifying that a given lot meets the specified quality level (SQL).
2016-05-13
WIP Standard
AS13007
1.1.1. This specification defines standardized methods for suppliers to be used when achieving AS9100 compliance. The intent of standardization is to increase supplier efficiency and reduce noncompliance due to from variation in customer to customer detailed requirements for the same basic item.
2016-04-20
Standard
AS9133A
This standard defines a system for the qualification of standard products for aviation, space, and defense applications. It defines the principles that shall be adhered to when carrying out product qualification; applied in conjunction with the rules and procedures of the CA. The system enables the CA to confirm compliance is achieved and maintained, in accordance with the requirements of its product definition and associated controlling technical specifications by an Original Component Manufacturer (OCM) of standard products. This standard requires an OCM that has been granted product qualification approval to ensure applicable approvals are maintained and renewed in accordance with the CA’s quality system for that qualified product. OCMs and OCM designated Value Added Distributors (VADs) requesting product qualification to this standard, shall as a prerequisite, maintain 9100 standard quality management system certification approval.
2016-04-18
WIP Standard
AS13001A
The standard applies to aero engine suppliers operating a self-release process as a delegated activity from the delegating organization. While primarily developed around the aero engine supply chain requirements, this standard can also be used in other industry sectors where a self-release process may be of benefit.
2016-04-08
WIP Standard
AMS2629E
This specification covers a mixture of liquid hydrocarbons and soluble additives.<p>To provide a standard composition, simulating aviation jet engine fuel. This fluid has been used typically in laboratory tests involving compatibility and interaction with aircraft materials, but usage is not limited to such applications.
2016-04-05
WIP Standard
AMS2374F
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specifications of corrosion and heat-resistant steel and alloy forgings.
2016-03-31
WIP Standard
AMS2371K
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought corrosion and heat-resistant steel and alloy products and of forging stock.
2016-03-29
Standard
AS9117
This standard specifies requirements for DPRV to establish common product/service requirements for use at all levels of the supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to their supplier (reference 9100 and 9110 standards); to perform product acceptance on their behalf. The delegating organization shall use this standard as the baseline for establishing a DPRV process, although they may include additional contract requirements to meet their specific needs.
2016-03-22
WIP Standard
AMS2670K
This specification covers the engineering requirements for producing brazed joints using copper as the brazing filler metal.
2016-03-22
WIP Standard
AMS2451/1B
This specification establishes the requirements for a general purpose brush plating of nickel applied by electrodeposition.
2016-03-22
WIP Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
2016-03-22
WIP Standard
AMS2753D
This specification covers the requirements for an epsilon-iron nitride case on ferrous parts produced by immersion in a low-temperature, agitated, fused salt bath.
2016-03-22
WIP Standard
AMS2451/9C
This specification covers the requirements for brush plating of zinc-nickel by electrodeposition.
2016-03-22
WIP Standard
AMS2615G
This specification provides requirements and procedures for hydraulic-pressure leak testing of parts.
2016-03-22
WIP Standard
AMS2451D
This specification and its supplementary detail specifications establish the requirements for electrodeposition of metals by brush plating.
2016-03-22
WIP Standard
AMS2451/10B
This specification covers the requirements for brush plating of tin-zinc by electrodeposition.
2016-03-22
WIP Standard
AMS2451/12A
This specification covers the engineering requirements and process for brush plating of tin by electrodeposition. It shall be used, in conjunction with AMS 2451, for general-purpose tin deposits.
2016-03-22
WIP Standard
AMS2451/11B
This specification covers the requirements for brush plating of cobalt by electrodeposition.
Viewing 1 to 30 of 1246

Filter

  • Standard
    1246