Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 542
CURRENT
2017-04-06
Standard
J3059_201704
This SAE Information Report describes the testing and reporting procedures that may be used to evaluate and document the excursion of a worker or civilian when transported in a seated and restrained position in the patient compartment of a ground ambulance when exposed to a front, side, or rear impact. Its purpose is to provide seating and occupant restraint manufacturers, ambulance builders, and end-users with testing procedures and documentation methods needed to identify head travel paths in crash loading events. This is a component level test. The seating system is tested in free space to measure maximum head travel paths. The purpose is not to identify stay out zones. Rather, the goal is to provide ambulance manufacturers with the data needed to design safer and functionally sound workstations for Emergency Medical Service workers so that workers are better able to safely perform patient care tasks in a moving ambulance.
CURRENT
2017-02-09
Standard
ARP1705C
The purpose of this procedure is to establish a technique for reliably and repeatedly measuring the RF shielding characteristics of EMI gasket materials and EMI gaskets against various joint surfaces. The procedure is also used to test the reliability of the gasketed joint combinations after being subjected to hostile environments.
CURRENT
2017-02-02
Standard
ARP577E
This SAE Aerospace Recommended Practice (ARP) specifies criteria for the design, development, standardization, and comprehension testing of placards containing pictures, drawings, symbols, and/or written instructions for locating and operating aircraft emergency equipment. This ARP also provides guidance in the selection and implementation of warning placards intended to instruct occupants inside, and rescue personnel outside, the aircraft.
CURRENT
2017-01-18
Standard
J2419_201701
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2017-01-06
Standard
J167_201701
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
CURRENT
2017-01-04
Standard
ARP6239
This SAE Aerospace Recommended Practice (ARP) recommends the design and features of aircraft demonstration emergency equipment for use in passenger safety briefings.
CURRENT
2017-01-03
Standard
ARP583J
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and location of cabin crew stations, including emergency equipment installations at or near such stations, so as to enable the cabin crew to function effectively in emergency situations, including emergency evacuations. Recommendations regarding design of cabin crew stations apply to all such stations; recommendations regarding location apply to those stations located near or adjacent to floor level exits.
CURRENT
2016-12-13
Standard
AS8049/1B
This SAE Aerospace Standard (AS) defines Minimum Performance Standards (MPS), qualification requirements, and minimum documentation requirements for side-facing seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a side-facing seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic test conditions set forth in Title 14, Code of Federal Regulations (CFR) Part 23, 25, 27, or 29. While this document addresses system performance, responsibility for the seating system is divided between the seat supplier and the installation applicant. The seat supplier’s responsibility consists of meeting all the seat system performance requirements and obtaining and supplying to the installation applicant all the data prescribed by this document.
CURRENT
2016-11-28
Standard
J2194_201611
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met.
CURRENT
2016-11-23
Standard
J1194_201611
Fulfillment of the intended purpose requires testing as follows:
CURRENT
2016-11-01
Standard
J3026_201611
This SAE Recommended Practice describes the testing procedures that may be used to evaluate the integrity of ground ambulance-based occupant seating and occupant restraint systems for workers and civilians transported in the patient compartment of an ambulance when exposed to a frontal or side impact. This Recommended Practice was based on ambulance patient compartment dynamics and is not applicable to other vehicle applications or seating positions. This Recommended Practice is structured to accommodate seating systems installed in multiple attitudes including but not limited to side-facing, rear-facing, and forward-facing.
CURRENT
2016-11-01
Standard
J3027_201611
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when exposed to a frontal, side or rear impact. Its purpose is to provide litter manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent ensures the patient litter, litter retention system, and patient restraint utilizes a similar dynamic performance test methodology to that which is applied to other vehicle seating and occupant restraint systems. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
CURRENT
2016-10-10
Standard
AMS3801/1C
This specification covers one weight and one weave of low-modulus meta-aramid cloth.
CURRENT
2016-08-23
Standard
J2956_201608
This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J3044_201608
This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J2917_201608
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-05-31
Standard
ARP4072A
This SAE Aerospace Recommended Practice (ARP) provides information and recommended guidelines for handling carry-on baggage prior to emergencies and during the emergency evacuation of transport category aircraft. Recommendations are provided on limiting the size, amount, and weight of carry-on baggage brought into the cabin, improved stowage of carry-on baggage to minimize hazards to passengers in flight and during emergency evacuations, and procedures to ensure carry-on baggage is not removed during an emergency evacuation.
2016-05-19
WIP Standard
AS1426C
This specification is intended to be used as a general standard for industry use for design and construction of air transport galley equipment and inflight food service systems.
CURRENT
2016-04-29
Standard
J2531_201604
New methods are available to assist in evaluating the risk of impulse noise-induced hearing loss from inflatable devices, for example, airbags and seat belt pretensioners. This document presents some background on impulse noise measurement techniques and assessment criteria. Related information relative to test details, for example, preamplifier specifications and filtering methods and criteria, will be discussed in a future recommended practice.
CURRENT
2016-04-28
Standard
J2937_201604
The objective of this document is to enhance the test procedure that is used for ejection mitigation testing per the NHTSA guidelines as mentioned in the FMVSS226 Final Rule document (NHTSA Docket No. NHTSA-2011-0004). The countermeasure for occupant ejection testing is to be tested with an 18kg mass on a guided linear impactor using the featureless headform specifically designed for ejection mitigation testing. SAE does not endorse any particular countermeasure for ejection mitigation testing. However, the document reflects guidelines that should be followed to maintain consistency in the test results. Examples of currently used countermeasures include the Inflatable Curtain airbags and Laminated Glass.
2016-03-16
WIP Standard
AS1046D
This standard is intended to apply to portable compressed gaseous oxygen equipment. When properly configured, this equipment is used either for the administration of supplemental oxygen, first aid oxygen or smoke protection to one or more occupants of either private or commercial transport aircraft.
HISTORICAL
2016-03-05
Standard
AS8049/1A
This SAE Aerospace Standard (AS) defines Minimum Performance Standards (MPS), qualification requirements, and minimum documentation requirements for side-facing seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a side-facing seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic test conditions set forth in Title 14, Code of Federal Regulations (CFR) Part 23, 25, 27, or 29. While this document addresses system performance, responsibility for the seating system is divided between the seat supplier and the installation applicant. The seat supplier’s responsibility consists of meeting all the seat system performance requirements and obtaining and supplying to the installation applicant all the data prescribed by this document.
CURRENT
2016-02-24
Standard
AS1354
This SAE Aerospace Standard (AS) provides the minimum design and performance requirements for individual, inflatable life preservers, divided into six categories: “Adult,” “Adult-Child,” “Child,” “Infant-Small Child,” “Adult-Child-Infant-Small Child,” and “Demonstration.”
CURRENT
2016-02-18
Standard
J2826_201602
This SAE Recommended Practice establishes the test equipment, procedure, and acceptance criteria necessary to determine the location of power driven components that could, upon inadvertent contact by an operator, passenger, or bystander, inflict injury.
CURRENT
2016-01-14
Standard
J2292_201601
This SAE Recommended Practice establishes minimum performance and test requirements for combination pelvic and upper torso occupant restraint systems provided for off-road self-propelled work machines.
2015-09-29
WIP Standard
J386
This standard provides performance and test requirements for operator restraint systems provided for off-road self-propelled work machines. This document applies to pelvic restraint systems (Type 1) for off-road, self-propelled work machines fitted with ROPS and commonly used in construction, earthmoving, forestry, and mining as referred to in SAE J1040 and industrial machines fitted with ROPS as referred to in SAE J1042.
CURRENT
2015-08-27
Standard
J2418_201508
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2015-06-04
Standard
J2426_201506
This SAE Recommended Practice describes the test procedures for conducting simulated dynamic lateral rollover restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
2015-05-20
WIP Standard
J1855
This SAE Recommended Practice describes the method for safe deployment of air bag modules in vehicles equipped with electrically actuated air bag systems for the purpose of disposal. It is intended to provide a procedure which does not require significant technical expertise, is easy to operate, and is readily available, to be used by automobile dismantlers or vehicle shredders to deploy air bag modules prior to automobile reclamation.
CURRENT
2015-04-09
Standard
J1538_201504
The terms included in the Glossary are general in nature and may not apply to all manufacturers’ systems. All terms in Section 3 apply to automotive inflatable restraint systems in general which are initiated by an electric or mechanical stimulus upon receipt of a signal from a sensor. These terms are intended to reflect existing designs and the Glossary will be updated as information on other types of systems becomes available. Appendix A is included to identify terminology that is no longer in common use or specifically applicable to inflatable restraint systems, but was published in the December 2001 version of SAE J1538.
Viewing 1 to 30 of 542

Filter