Criteria

Text:
Display:

Results

Viewing 1 to 30 of 2783
2017-08-09
Tech Insights
TI-0001
As the aerospace industry continues on its quest for ever-increased efficiency, so goes the quest for ever-more composite content on aircraft. And with it, more opportunities to repair it. Typical composite panel fiber reinforcements are carbon, aramid, and fiberglass. The machining techniques for these typical composite materials are similar, but minor differences exist, such as the style of cutting tool or drill bit. Automated drilling methods that may be used during original manufacture are rarely used in typical composite repair situations.
2017-03-28
Technical Paper
2017-01-1468
Do Hoi KIm
Previous work identified a relationship between vehicle drop and dummy injury under the high-speed frontal impact condition [1]. The results showed that vehicle drop greater than 60mm made the dummy injury worse. Moreover, that work identified the front side member as the crucial part affecting the vehicle drop. In this study, the body structure mechanism was studied to reduce vehicle drop by controlling the front side member, shotgun, and A-pillar. By analyzing full vehicles, it was recognized that the arch shape of the front side member was very important. Furthermore, if the top of the arch shape of front side member, shotgun, and A-pillar were connected well, then the body deformation energy could lift the lower part of A-pillar, effectively reducing vehicle drop. This structure design concept is named “Body Lift Structure” (BLS). The BLS was applied to B and C segment platforms. Additionally, a “Ring” shape was defined by the front side member, dash panel, and A-pillar.
2017-03-28
Technical Paper
2017-01-1471
Xiao Luo, Wenjing Du, Hao Li, Peiyu LI, Chunsheng Ma, Shucai Xu, Jinhuan Zhang
Abstract Occupant restraint systems are developed based on some baseline experiments. While these experiments can only represent small part of various accident modes, the current procedure for utilizing the restraint systems may not provide the optimum protection in the majority of accident modes. This study presents an approach to predict occupant injury responses before the collision happens, so that the occupant restraint system, equipped with a motorized pretensioner, can be adjusted to the optimal parameters aiming at the imminent vehicle-to-vehicle frontal crash. The approach in this study takes advantage of the information from pre-crash systems, such as the time to collision, the relative velocity, the frontal overlap, the size of the vehicle in the front and so on. In this paper, the vehicle containing these pre-crash features will be referred to as ego vehicle. The information acquired and the basic crash test results can be integrated to predict a simplified crash pulse.
2017-03-28
Technical Paper
2017-01-0264
Venkatesh Babu, Ravi Thyagarajan, Jaisankar Ramalingam
Abstract In this paper, the capability of three methods of modelling detonation of high explosives (HE) buried in soil viz., (1) coupled discrete element & particle gas methods (DEM-PGM) (2) Structured - Arbitrary Lagrangian-Eulerian (S-ALE), and (3) Arbitrary Lagrangian-Eulerian (ALE), are investigated. The ALE method of modeling the effects of buried charges in soil is well known and widely used in blast simulations today [1]. Due to high computational costs, inconsistent robustness and long run times, alternate modeling methods such as Smoothed Particle Hydrodynamics (SPH) [2, 9] and DEM are gaining more traction. In all these methods, accuracy of the analysis relies not only on the fidelity of the soil and high explosive models but also on the robustness of fluid-structure interaction. These high-fidelity models are also useful in generating fast running models (FRM) useful for rapid generation of blast simulation results of acceptable accuracy.
2017-03-28
Technical Paper
2017-01-1460
Nitesh Jadhav, Linda Zhao, Senthilkumar Mahadevan, Bill Sherwood, Krishnakanth Aekbote, Dilip Bhalsod
Abstract The Pelvis-Thorax Side Air Bag (PTSAB) is a typical restraint countermeasure offered for protection of occupants in the vehicle during side impact tests. Currently, the dynamic performance of PTSAB for occupant injury assessment in side impact is limited to full-vehicle evaluation and sled testing, with limited capability in computer aided engineering (CAE). The widely used CAE method for PTSAB is a flat bag with uniform pressure. The flat PTSAB model with uniform pressure has limitations because of its inability to capture airbag deployment during gap closure which results in reduced accuracy while predicting occupant responses. Hence there is a need to develop CAE capability to enhance the accuracy of prediction of occupant responses to meet performance targets in regulatory and public domain side impact tests. This paper describes a new CAE methodology for assessment of PTSAB in side impact.
2017-03-28
Technical Paper
2017-01-1459
HangMook Kim, Jae Kyu Lee, Jin Sang CHUNG
Abstract During a new vehicle development process, there are several requirements for side impact test that should be confirmed. One of the requirements is the prevention of door opening during side impact test. Even though there are many causes for door opening problem, this study deals with inertia effect by impact energy. Until now, there have been two classical methods to prevent car door from opening in side impact. One is the increment of the inertia resistance by increasing the mass of the balance weight and the spring force. The other is the application of the blocking lever. Unfortunately, in spite of our efforts, the door opening problem occurs occasionally. Therefore, to improve the problem fundamentally, this paper proposes a new blocking lever mechanism that work similar to ball-point pen structure. The proposed mechanism fixes the blocking lever when the opening directional inertia force is applied to the door outside handle during side crash.
2017-03-28
Technical Paper
2017-01-1457
Jingwen Hu, Nichole Ritchie Orton, Rebekah Gruber, Ryan Hoover, Kevin Tribbett, Jonathan Rupp, Dave Clark, Risa Scherer, Matthew Reed
Abstract Among all the vehicle rollover test procedures, the SAE J2114 dolly rollover test is the most widely used. However, it requires the test vehicle to be seated on a dolly with a 23° initial angle, which makes it difficult to test a vehicle over 5,000 kg without a dolly design change, and repeatability is often a concern. In the current study, we developed and implemented a new dynamic rollover test methodology that can be used for evaluating crashworthiness and occupant protection without requiring an initial vehicle angle. To do that, a custom cart was designed to carry the test vehicle laterally down a track. The cart incorporates two ramps under the testing vehicle’s trailing-side tires. In a test, the cart with the vehicle travels at the desired test speed and is stopped by a track-mounted curb.
2017-03-28
Technical Paper
2017-01-1448
Kevin Pline, Derek Board, Nirmal Muralidharan, Srinivasan Sundararajan, Eric Eiswerth, Katie Salciccioli
Abstract Ford Motor Company introduced the automotive industry’s first second row inflatable seatbelt system in 2011. The system is currently available in the outboard seating positions of the second row of several Ford and Lincoln models. An important consideration for this system is the interaction with child restraint systems (CRS) when it is used to install a CRS or used in conjunction with belt position booster. A novel test methodology to assess the interaction of CRS with Ford and Lincoln inflatable seatbelts through frontal impact sled tests is explained. Details of test methods including construction of additional fixtures and hardware are highlighted. This procedure is designed to enable test labs capable of running Federal Motor Vehicle Safety Standard (FMVSS) 213 testing to adapt this test method, with minimal fabrication, by utilizing existing test benches.
2017-03-28
Technical Paper
2017-01-1431
Ke Dong, Brian Putala, Kristen Ansel
Abstract Driver out-of-position (OOP) tests were developed to evaluate the risk of inflation induced injury when the occupant is close to the airbag module during deployment. The Hybrid III 5th percentile female Anthropomorphic Test Device (ATD) measures both sternum displacement and chest acceleration through a potentiometer and accelerometers, which can be used to calculate sternum compression rate. This paper documents a study evaluating the chest accelerometers to assess punch-out loading of the chest during this test configuration. The study included ATD mechanical loading and instrumentation review. Finite element analysis was conducted using a Hybrid III - 5th percentile female ATD correlated to testing. The correlated restraint model was utilized with a Hybrid III - 50th percentile male ATD. A 50th percentile male Global Human Body Model (HBM) was then applied for enhanced anatomical review.
2017-03-28
Technical Paper
2017-01-1429
Sung Rae kim, Inju Lee, Hyung joo Kim
Abstract This paper aims to evaluate the biofidelity of a human body FE model with abdominal obesity in terms of submarining behavior prediction, during a frontal crash event. In our previous study, a subject-specific FE model scaled from the 50th percentile Global Human Body Model Consortium (GHBMC) human model to the average physique of three female post mortem human subjects (PMHSs) with abdominal obesity was developed and tested its biofidelity under lap belt loading conditions ([1]). In this study frontal crash sled simulations of the scaled human model have been performed, and the biofidelity of the model has been evaluated. Crash conditions were given from the previous study ([2]), and included five low-speed and three high-speed sled tests with and without anti-submarining device.
2017-03-28
Technical Paper
2017-01-1299
Nagurbabu Noorbhasha, Brendan J. O'Toole
Abstract The objective of this research is to design and analyze a roll cage structure for an off-road vehicle that was used for SAE Baja competition by UNLV SAE Baja team. Baja SAE is an intercollegiate competition to design, fabricate, and race a small, single passenger, off-road vehicle powered by a 10 HP Briggs Stratton 4-Stroke gasoline engine. Since the off-road vehicle is powered by a small capacity engine, the weight of the structure is very critical and must be optimized to improve the performance of the vehicle. In an effort to optimize the structure, a finite element analysis (FEA) was performed and the effects of stress and deformation were studied for a linear static frontal impact analysis on roll cage structure. The frame was further modified for structural rigidity. Additional strengthening gussets were added at the locations of high stresses to reduce the stress concentration.
2017-03-28
Technical Paper
2017-01-1307
Puneet Bahri, Praveen Balaj Balakrishnan, Ravi Purnoo Munuswamy
Abstract Automotive industries are emphasizing more and more on occupant safety these days, due to an increase in awareness and demand to achieve high safety standards. They are dependent on simulation tools to predict the performance of subsystems more accurately. The challenges being encountered are designs which are getting more complex and limitations in incorporating all real-life scenarios, such as to include all manufacturing considerations like forming and welding effects. Latest versions of solvers are slowly introducing new options to include these actual scenarios. Ls-Dyna is one of the explicit solvers to introduce these possibilities. The process of including stamping details into crash simulation is already being performed in the automotive industry. However, for seatbelt pull analysis, this has not been explored much.
2017-03-28
Journal Article
2017-01-1445
Kevin Pline, Derek Board, Nirmal Muralidharan, Srinivasan Sundararajan, Eric Eiswerth, Katie Salciccioli, Noelle Baker
Abstract Ford Motor Company introduced the inflatable seatbelt system in 2011 and the system is now available in the second row of several Ford and Lincoln models. An important consideration is the interaction of the inflatable seatbelt system with child restraint systems (CRS). A comprehensive series of frontal impact sled tests, using a standardized test method, was conducted to compare the performance of rear-facing-only CRS installed using an inflatable seatbelt to the same CRS installed using a standard seatbelt. CRS models from several manufacturers in the North American market were tested both with and without their bases. CRABI 12 month old or Hybrid III 3 year old anthropomorphic test devices (ATD) were restrained in the CRS. The assessment included the ability to achieve a satisfactory installation with the inflatable seatbelt, comparisons of ATD and CRS kinematics, CRS system integrity, and comparisons of ATD responses.
2017-03-28
Technical Paper
2017-01-1446
Allen Charles Bosio, Paul Marable, Marcus Ward, Bradley Staines
Abstract A dual-chambered passenger airbag was developed for the 2011 USNCAP to minimize neck loading for the belted 5th female dummy while restraining the unbelted 50th dummy for FMVSS208. This unique, patented design adaptively controlled venting between chambers based on occupant stature. A patented pressure-responsive vent on the second chamber permitted aspiration into the second chamber before a delayed outflow to the environment. The delayed flow through the pressure-responsive vent from the second chamber acted like a pressure-limiting membrane vent to advantageously reduce the injury assessment values for the HIC and the Nij for the 5th female dummy.
2017-03-28
Technical Paper
2017-01-1474
Raed E. El-Jawahri, Agnes Kim, Dean Jaradi, Rich Ruthinowski, Kevin Siasoco, Cortney Stancato, Para Weerappuli
Abstract Sled tests simulating full-frontal rigid barrier impact were conducted using the Hybrid III 5th female and the 50th male anthropomorphic test devices (ATDs). The ATDs were positioned in the outboard rear seat of a generic small car environment. Two belt configurations were used: 1) a standard belt with no load limiter or pre-tensioner and 2) a seatbelt with a 4.5 kN load-limiting retractor with a stop function and a retractor pre-tensioner (LL-PT). In the current study, the LL-PT belt system reduced the peak responses of both ATDs. Probabilities of serious-to-fatal injuries (AIS3+), based on the ATDs peak responses, were calculated using the risk curves in NHTSA’s December 2015 Request for Comments (RFC) proposing changes to the United States New Car Assessment Program (US-NCAP). Those probabilities were compared to the injury rates (IRs) observed in the field on point estimate basis.
2017-03-28
Technical Paper
2017-01-0361
Amar Marpu, George Garfinkel, Patrick Maguire
Abstract Modeling of High Voltage (HV) wires is an important aspect of vehicle safety simulations for electrified powertrains to understand the potential tearing of the wire sheath or pinching of HV wiring. The behavior of the HV wires must be reviewed in safety simulations to identify potential hazards associated with HV wire being exposed, severed, or in contact with ground planes during a crash event. Modeling HV wire is challenging due to the complexity of the physical composition of the wire, which is usually comprised of multiple strands bundled and often twisted together to form the HV electrical conductor. This is further complicated by the existence of external insulating sheathing materials to prevent HV exposure during normal operating conditions. This paper describes a proposed method to model and characterize different types of HV wires for usage in component- and vehicle-level safety models.
2017-03-28
Technical Paper
2017-01-1418
Wesley D. Grimes, Thomas Vadnais, Gregory A. Wilcoxson
Abstract The time/distance relationship for a heavy truck accelerating from a stop is often needed to accurately assess the events leading up to a collision. Several series of tests were conducted to document the low speed acceleration performance of a 2016 Kenworth T680 truck tractor equipped with a ten-speed overdrive automated manual transmission in Auto Mode. Throughout the testing, the driver never manually shifted gears. This testing included three trailer load configurations and two different acceleration rates. Data were gathered with a VBOX and the Cummins INSITE software.
2017-03-28
Technical Paper
2017-01-1420
Kirsten White, Raymond Merala
Abstract This study presents a method to characterize the accuracy and precision of video-acceleration-position (VAP) devices, and presents results from testing of one such vehicle camera (“dashcam”) with global positioning system (GPS) used by taxi companies nationwide. Tests were performed in which vehicle kinematic data were recorded in a variety of real world conditions simultaneously by the VAP device, accelerometers, and a proven GPS-based speed sensing and data acquisition system. Data from the VAP device was compared to data collected by the reference instruments to assess timing, precision, and accuracy of reported parameters. Still images from the VAP video recording were compared with three dimensional laser scan data in order to analyze field of view. Several case studies are discussed, and some guidelines and cautions are provided for use of VAP data in accident reconstruction applications.
2017-03-28
Technical Paper
2017-01-1414
William Bortles, David Hessel, William Neale
Abstract When a vehicle with protruding wheel studs makes contact with another vehicle or object in a sideswipe configuration, the tire sidewall, rim and wheel studs of that vehicle can deposit distinct geometrical damage patterns onto the surfaces it contacts. Prior research has demonstrated how relative speeds between the two vehicles or surfaces can be calculated through analysis of the distinct contact patterns. This paper presents a methodology for performing this analysis by visually modeling the interaction between wheel studs and various surfaces, and presents a method for automating the calculations of relative speed between vehicles. This methodology also augments prior research by demonstrating how the visual modeling and simulation of the wheel stud contact can extend to almost any surface interaction that may not have any previous prior published tests, or test methods that would be difficult to setup in real life.
2017-03-28
Technical Paper
2017-01-0373
Fabian Jorg Uwe Koark, Christian Beul
Abstract Achieving functional safety in mechatronic systems with growing product functionality is a major challenge in systems engineering. Following the current discussion, this challenge is mostly allocated to electronics and software development. For most of the scenarios this focus is feasible. Product design - the construction of the product - defines the properties and the appearance of the product by shape, material and assembly. So, the product design is often not under control of the safety management system. A hazardous deviation of part shape can be easily identified after the parts product or at least at its mounting. A wrong assembly is controlled by assembly documentation or data (e.g. screw torques) and identified at end of assembly line checks. The identification of a hazardous material choice depends on the product material class. Product materials can be separated into two classes: passive or active materials.
2017-03-28
Technical Paper
2017-01-0377
Peter Shery, William Altenhof, Ryan Smith, Elmar Beeh, Philipp Strassburger, Thomas Gruenheid
Abstract Cylindrical extrusions of magnesium AZ31B were subjected to quasi-static axial compression and cutting modes of deformation to study this alloy’s effectiveness as an energy absorber. For comparison, the tests were repeated using extrusions of AA6061-T6 aluminum of the same geometry. For the axial compression tests, three different end geometries were considered, namely (1) a flat cutoff, (2) a 45 degree chamfer, and (3) a square circumferential notch. AZ31B extrusions with the 45 degree chamfer produced the most repeatable and stable deformation of a progressive fracturing nature, referred to as sharding, with an average SEA of 40 kJ/kg and an average CFE of 45 %, which are nearly equal to the performance of the AA6061-T6. Both the AZ31B specimens with the flat cutoff and the circumferential notch conditions were more prone to tilt mid-test, and lead to an unstable helical fracture, which significantly reduced the SEA.
2017-03-28
Technical Paper
2017-01-1413
Nathan A. Rose, Neal Carter, David Pentecost, Alireza Hashemian
Abstract This paper investigates the dynamics of four motorcycle crashes that occurred on or near a curve (Edwards Corner) on a section of the Mulholland Highway called “The Snake.” This section of highway is located in the Santa Monica Mountains of California. All four accidents were captured on video and they each involved a high-side fall of the motorcycle and rider. This article reports a technical description and analysis of these videos in which the motion of the motorcycles and riders is quantified. To aid in the analysis, the authors mapped Edwards Corner using both a Sokkia total station and a Faro laser scanner. This mapping data enabled analysis of the videos to determine the initial speed of the motorcycles, to identify where in the curve particular rider actions occurred, to quantify the motion of the motorcycles and riders, and to characterize the roadway radius and superelevation throughout the curve.
2017-03-28
Technical Paper
2017-01-1423
Alan F. Asay, Christopher D. Armstrong, Bradley Higgins, John Steiner
Abstract The rear override crash behavior of full-size and light duty pickup trucks was examined. A series of ten full-scale, front and rear override impact crash tests were conducted involving four full-size pickup trucks, two light duty pickup trucks, and one sport utility vehicle (SUV). The tests were conducted utilizing a fabricated steel rigid barrier mounted on the front of the Massive Moving Barrier (MMB) test device with full overlap of the test vehicle. Crush ranged from 25.0 to 77.9 inches for impact speeds of 21.7 to 36.0 mph. These override tests on pickups were conducted to provide more basis in an area that is underrepresented in the literature. Each test was documented and measured prior to, and following, the crash test. The stiffness parameters were calculated and presented using constant stiffness, force saturation, and the power law damage models.
2017-03-28
Technical Paper
2017-01-1436
Edward Fatzinger, Jon Landerville
Abstract Various electronic control units from Kawasaki Ninja 300 motorcycles were tested in-situ in order to heuristically examine the capabilities and behavior of the event data recorders (EDR). The relevant hexadecimal data was downloaded from the ECU and translated using known and historically proven applications. The hexadecimal translations were then confirmed using data acquisition systems as well as the Kawasaki Diagnostic Software (KDS). Numerous tests were performed to establish the algorithms which cause the EDR to record data. It was determined that the EDR recording “trigger” was caused by the activation of the tip-over sensor, which in turn shuts the engine off. In addition, specific conditions must be met with regards to the rear wheel rotation prior to engine shut-down.
2017-03-28
Journal Article
2017-01-0268
Venkatesh Babu, Richard Gerth
Abstract The aim of this analysis was to model the effect of adding stiffening ribs in structural aluminum components by friction stir processing (FSP) Nano material into the aluminum matrix. These stiffening ribs could dampen, redirect, or otherwise alter the transmission of energy waves created from automotive, ballistic, or blast shocks to improve noise, vibration, and harshness (NVH) and structural integrity (reduced joint stress) response. Since the ribs are not created by geometry changes they can be space efficient and deflect blast / ballistic energy better than geometry ribbing, resulting in a lighter weight solution. The blast and ballistic performance of different FSP rib patterns in AL 5182 and AL 7075 were simulated and compared to the performance of an equivalent weight of RHA plate FSP helps to increase localized strength and stiffness of the base metal, while achieving light weighting of the base metal.
2017-03-28
Technical Paper
2017-01-1433
Enrique Bonugli, Joseph Cormier, Matthew Reilly, Lars Reinhart
The purpose of this study was to determine the frictional properties between the exterior surface of a motorcycle helmet and ‘typical’ roadway surfaces. Motorcycle helmet impacts into asphalt and concrete surfaces were compared to abrasive papers currently recommended by government helmet safety standards and widely used by researchers in the field of oblique motorcycle helmet impact testing. A guided freefall test fixture was utilized to obtain nominal impact velocities of 5, 7 and 9 m/s. The impacting surfaces were mounted to an angled anvil to simulate an off-centered oblique collision. Helmeted Hybrid III ATD head accelerations and impact forces were measured for each test. The study was limited to a single helmet model and impact angle (30 degrees). Analysis of the normal and tangential forces imparted to the contact surface indicated that the frictional properties of abrasive papers differ from asphalt and concrete in magnitude, duration and onset.
2017-03-28
Journal Article
2017-01-0367
Yueqian Jia, Yu-wei Wang, Yuanli Bai
Abstract A fully modularized framework was established to combine isotropic, kinematic, and cross hardening behaviors under non-monotonic loading conditions for advanced high strength steels. Experiments under the following types of non-proportional loading conditions were conducted, 1) uniaxial tension-compression-tension/compression-tension-compression full cycle reversal loading, 2) uniaxial reversal loading with multiple cycles, and 3) reversal shear. The calibrated new model is decoupled between isotropic and kinematic hardening behaviors, and independent on both anisotropic yield criterion and fracture model. Nine materials were calibrated using the model, include: DP590, DP600, DP780, TRIP780, DP980LY, QP980, AK Steel DP980, TBF1180, and AK Steel DP1180. Good correlation was observed between experimental and modeled results.
2017-03-28
Journal Article
2017-01-0365
Kentaro Sato, Takayuki Futatsuka, Jiro Hiramoto, Kei Nagasaka, Akira Akita, Takeshi Kashiyama
Abstract A simple testing method is proposed in order to investigate ductile fracture in crashed automotive components made from advanced high strength steels. This type of fracture is prone to occur at spot-welded joints and flange edges. It is well known that the heat affected zone (HAZ) is a weak point in high strength steel due to the formation of annealed material around the spot-welded nugget, and the flange edge also has low ductility due to the damage caused by shearing. The proposed method is designed to simulate a ductile fracture which initiates from a spot-welded portion or a sheared edge in automotive components which are deformed in a crash event. Automotive steel sheets with a wide range of tensile strengths from 590MPa to 1470MPa are examined in order to investigate the effect of material strength on fracture behavior. The effects of material cutting methods, namely, machining and shearing, are also investigated.
2017-03-28
Journal Article
2017-01-0378
Yuta Imanami, Kunikazu Tomita, Kazuaki Fukuoka, Kimihiro Nishimura
Abstract In order to develop a new carburizing steel material that realizes an intermediate heat treatment-free process in parts manufacturing, the cold forgeability of the as-rolled steel and suppression of abnormal grain growth of austenite were studied. It was shown that adjustment of addition amount of Si, Mn and Cr, suppression of dynamic strain aging during cold forging, and an increase of ferrite fraction by controlled rolling contribute to the reduction of deformation resistance. However, Nb precipitation control by fully utilizing mill manufacturing processes was also necessary for suppression of abnormal grain growth of austenite. A new steel for carburizing was developed by integrating these technologies, making it possible to eliminate annealing before cold forging and normalizing before carburizing simultaneously. Thus, the developed steel is an important innovation in the parts manufacturing process.
2017-03-28
Journal Article
2017-01-0379
Tau Tyan, Leonard Shaner, Matt Niesluchowski, Nand Kochhar, Dilip Bhalsod, Jason Wang
Three computational gas and fluid dynamic methods, CV/UP (Control Volume/Uniform Pressure), CPM (Corpuscular Particle Method), and ALE (Arbitrary Lagrangian and Eulerian), were investigated in this research in an attempt to predict the responses of side crash pressure sensors. Acceleration-based crash sensors have been used extensively in the automotive industry to determine the restraint system firing time in the event of a vehicle crash. The prediction of acceleration-based crash pulses by using computer simulations has been very challenging due to the high frequency and noisy responses obtained from the sensors, especially those installed in crush zones. As a result, the sensor algorithm developments for acceleration-based sensors are largely based on prototype testing. With the latest advancement in the crash sensor technology, side crash pressure sensors have emerged recently and are gradually replacing acceleration-based sensor for side crash applications.
Viewing 1 to 30 of 2783