Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 422
CURRENT
2017-03-09
Standard
J915_201703
The scope and purpose of this SAE Recommended Practice is to provide a standard pattern or sequence for the manual control of automatic transmissions in passenger cars and light-duty trucks. This generally refers to left hand drive mechanical shift applications.
2016-10-23
WIP Standard
J647
The following schematic diagrams exemplify the SAE recommended method of illustrating automotive transmission arrangements. They were developed to standardize industry practice and facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of diagrams are used: Transmission in neutral and in gear. For illustrative purposes, some typical transmissions are shown.
2016-10-23
WIP Standard
J649
The following is a list of the most common terminology used in describing automatic transmission functions.
2016-10-23
WIP Standard
J645
The following listed definitions are intended to establish terminology and criteria for describing the various kinds of automotive transmissions. A specific arrangement may be described by a combination of several of these definitions.
2016-09-27
WIP Standard
J1117
To provide a uniform procedure for measuring and reporting the pressure losses associated with the significant flow paths in a hydraulic fluid power valve. This procedure applies to hydraulic fluid power valves as applied to self-propelled work machines as referenced in SAE J1116.
2016-09-27
WIP Standard
J717
This SAE Standard establishes specifications for mid- and side-power take-off drives that will be helpful in designing implements. Design of the implement attaching means must be tailored to each tractor, depending on attaching points available and the exact location of the auxiliary shaft.
2016-08-23
WIP Standard
J311
This SAE Information Report details some of the equipment and procedures used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It is intended to assist those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for the use in passenger car and light-duty truck automatic transmissions. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automatic transmission fluids.
CURRENT
2016-05-26
Standard
J2208_201605
To provide a Recommended Practice for validating the function and integrity of an automatic transmission park mechanism with its associated control system and environment.
CURRENT
2016-04-29
Standard
J2716_201604
This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. This document is a communication interface specification and no to be treated as product specification. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.
CURRENT
2016-01-26
Standard
J1946_201601
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.
CURRENT
2016-01-15
Standard
J2301_201601
This document specifies the main dimensions and tolerances, which affect interchangeability between end yoke earwork for the most common North American used universal joints. Dimensions and tolerances of the mating universal joints are left to the discretion of the universal joint manufacturers. The term “Earwork” refers to the configuration and geometry defining end yoke connections directly provided for universal joint cross attachment of drivelines. Earwork for certain styles of universal joint connections and flange connections have for a long time been proprietary to certain manufacturers. Over years of usage, proprietary rights have expired and the industry, as a whole, has used these earworks as standard. In an effort to tabulate some of the long established practices, the following SAE Recommended Practice has been compiled. Manufacturers do from time to time, as the need arises, change tolerances or fits to better enhance component performance.
CURRENT
2016-01-15
Standard
J2028_201601
This SAE Recommended Practice outlines the qualification testing and performance related criteria of elastomeric boot seals used in constant velocity joint applications. These applications are referred to as front- wheel-drive halfshafts or axles, but can also be utilized in rear-wheel-drive halfshaft applications. For additional information regarding CV joint systems and their applications refer to SAE AE-7 “Universal Joint and Driveshaft Design Manual.”
2016-01-07
WIP Standard
J3118
This SAE standard covers drive shaft interface types used in passenger car and light truck applications. Drive shaft interfaces include interfaces to the transmission, transfer case, and axles. Reference SAE standard J1946 for detailed specifications of type A and S flanges.
2016-01-06
WIP Standard
J2059
In this SAE Recommended Practice, attention will be given to passenger cars and light trucks (through Class III). The purpose of this recommended practice is to define standardized symbols that describe the arrangement and function of drivetrain systems and components of all-wheel-drive vehicles. This document presents basic symbols, superimposed symbols and symbols with modifiers. Various vehicle drivetrain schematics are shown with specific component arrangements or general driveline layout to illustrate varying levels of descriptive intent.
CURRENT
2015-06-30
Standard
J651_201506
The extent of test conditions on the dynamometer must be sufficient to determine the efficiency characteristics corresponding to the following range of vehicle operations in all gear ratios with locked torque converters (open converter can also be done where appropriate and noted). Efficiency versus output speed versus input torque Torque ratio versus output speed Input speed versus output speed Output torque versus output speed Parasitic loss versus input speed (spin losses) Cooler flow Output torque bias (front wheel drive transaxles)
CURRENT
2015-06-25
Standard
CPGM1_16LE2CRUZ
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
2015-06-23
WIP Standard
J3104
This SAE recommended practice document will cover most common applications of electric and electronic actuators used for controlling on-demand AWD disconnect systems used in passenger (car and light truck) vehicles. The specification will provide consistent definition, terminology, test methods and reporting methods.
CURRENT
2015-05-26
Standard
CPGM2_16LE2CRUZ
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2015-05-12
Standard
J755_201505
This SAE Standard specifies basic tolerances and dimensions for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).
CURRENT
2015-04-15
Standard
J2455_201504
Product for which data is to be available is for class 6 and larger, i.e., gross vehicle weight > 9.6 kg (19 500 lb).
CURRENT
2015-03-17
Standard
J2311_201503
This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.
CURRENT
2014-12-03
Standard
J1521_201412
This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
CURRENT
2014-10-13
Standard
CPKW1_15FS730V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
CURRENT
2014-10-13
Standard
CPKW2_15FS730V
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2014-10-10
Standard
CPFD2_15MUSTMAN
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2014-10-10
Standard
CPFD1_15MUSTMAN
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
CURRENT
2014-10-10
Standard
CPFD2_15MUSTAUT
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2014-10-08
Standard
ARP5454B
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
CURRENT
2014-09-18
Standard
J1403_201409
The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on vacuum lines of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.
HISTORICAL
2014-08-11
Standard
J1979_201408
This document supersedes SAE J1979 May 2007, and is technically equivalent to ISO 15031-5 2010, with the addition of new capabilities required by revised regulations from the California Air Resources Board and revised regulations from the European Commission. This document is intended to satisfy the data reporting requirements of On-Board Diagnostic (OBD) regulations in the United States and Europe, and any other region that may adopt similar requirements in the future.
Viewing 1 to 30 of 422