Criteria

Text:
Display:

Results

Viewing 151 to 180 of 44126
2017-10-08
Technical Paper
2017-01-2395
Arjun Prakash, Allen Aradi, William Imoehl, Phil Armitage
The impact of fuel composition (ethanol and aromatic content) and injector design on particulate number generation was studied in a 1.0L displacement direct injection spark ignition engine. Two types of engine tests that mimic real-life vehicle operation were carried out using a matrix of eight fuels and two injectors. It was found that the DISI injector design had the biggest impact on the extent of particulate number generation. An injector prototype designed to meet Euro 6c specifications for PN (6*1011 particles/km) resulted in much lower PN values compared to those obtained using a production injector currently available in the market. The impact of fuel composition on PN was apparent only during engine operation with the production injector. Overall, qualitative trends were observed but no statistically significant differences were observed for the impact of ethanol (E10 fuel match-blended for aromatics and octane quality) and aromatic content (19-28%) variation.
2017-10-08
Technical Paper
2017-01-2398
Bei Liu, Xiaobei Cheng, Jialu Liu, Han Pu, Li Yi
Abstract Partially-premixed low-temperature combustion avoids the soot and NOx generation area on the Ф-T diagram to reduce both engine NOx and soot emissions. Compared with the HCCI combustion mode, partially-premixed combustion (PPC) has better combustion controllability. The purpose of controlling the combustion phase can be achieved by adjusting injection timing and strategy. Based on a 4 cylinder turbocharged diesel engine, this paper aims at investigating the influence of injection strategy to the engine combustion and emission formation under the condition of single injection and split injection PPC strategy respectively, in which the primary purpose focus on the emission characteristics of particles. Results show that the early-injection PPC formed by single injection can reduce the quantity, quality and geometric mean diameter (GMD) of particles obviously.
2017-10-08
Technical Paper
2017-01-2399
Jianyu Duan, Kai Sun, Lei Li
Abstract Particulate matter emissions have become a concern for the development of DISI engines. EGR has been extensively demonstrated as a beneficial technology to migrate knock performance, improve fuel economy and reduce NOX emissions. Recently, the effect of EGR on particulate matter emissions is attracting increased attention. This work investigates the effects of EGR on PN emissions with the variations of engine operating parameters and aims to understand the role of EGR in PN emissions for DISI engines. A 1.8liter turbocharged engine with cooled EGR is used for this study. The engine is operated at steady-state conditions with EGR under various operating parameters including injection timing, excess air ratio, and spark timing to characterize the particle number emissions. The results indicates that there is a high sensitivity of PN emissions to EGR with the variations of those parameters.
2017-10-08
Technical Paper
2017-01-2406
Wu Yang, Xiuting Yin, Zhang Song Zhan, Huixian Shen, Huibin Qing, Qingqiang Zeng, Liyun Kang
Abstract This work addresses the problem of fatigue strength prediction of crankshaft fillet rolling processes to improve its accuracy. It is empirical to usually consider the effect of fillet rolling process on crankshaft fatigue performance. The fatigue performance of rolling process is mainly determined by induced compressive residual stresses, increased hardness and reduced roughness. Because the first two factors are difficult to measure the arc surface of fillet rolled cranks, it is difficult to predict the enhanced rate of crankshaft rolled performance to baseline unrolled’s. In this work a prediction method of fatigue strength for ductile cast iron crankshafts rolling process is presented. This method indirectly predicts the effect of the increased hardness on fatigue performance by the resonant bending fatigue test and modelling of crankshaft fillet rolling dynamic for the induced compressive residual stress.
2017-10-08
Technical Paper
2017-01-2405
Christophe Chaillou, Alexandre Bouet, Arnaud Frobert, Florence Duffour
Abstract Fuels from crude oil are the main energy vector used in the worldwide transport sector. But conventional fuel and engine technologies are often criticized, especially Diesel engines with the recent “Diesel gate”. Engine and fuel co-research is one of the main leverage to reduce both CO2 footprint and criteria pollutants in the transport sector. Compression ignition engines with gasoline-like fuels are a promising way for both NOx and particulate emissions abatement while keeping lower tailpipe CO2 emissions from both combustion process, physical and chemical properties of the low RON gasoline. To introduce a new fuel/engine technology, investigation of pollutants and After-Treatment Systems (ATS) is mandatory. Previous work [1] already studied soot behavior to define the rules for the design of the Diesel Particulate Filter (DPF) when used with a low RON gasoline in a compression ignition engine.
2017-10-08
Technical Paper
2017-01-2403
Yanzhao An, R Vallinayagam, S Vedharaj, Jean-Baptiste Masurier, Alaaeldin Dawood, Mohammad Izadi Najafabadi, Bart Somers, Bengt Johansson
Abstract In-cylinder visualization, combustion stratification, and engine-out particulate matter (PM) emissions were investigated in an optical engine fueled with Haltermann straight-run naphtha fuel and corresponding surrogate fuel. The combustion mode was transited from homogeneous charge compression ignition (HCCI) to conventional compression ignition (CI) via partially premixed combustion (PPC). Single injection strategy with the change of start of injection (SOI) from early to late injections was employed. The high-speed color camera was used to capture the in-cylinder combustion images. The combustion stratification was analyzed based on the natural luminosity of the combustion images. The regulated emission of unburned hydrocarbon (UHC), carbon monoxide (CO) and nitrogen oxides (NOX) were measured to evaluate the combustion efficiency together with the in-cylinder rate of heat release.
2017-10-08
Technical Paper
2017-01-2409
Erbao Zhang, Yinchun Gong, Jun Deng, Zongjie Hu, Chuanqian Jiang, Zhijun Wu, Liguang Li
Abstract The work of this paper aimed at investigating the cyclic variations of argon power cycle engine with fuel of hydrogen at lean burn operating conditions. The engine had been modified based on a 0.402 L, single-cylinder diesel engine into spark ignition engine with a port fuel injection system. The influencing factors on the cyclic variations, such as ignition timing, engine speed and compression ratio, were tested in this study. In all tests, the throttle opened at 0%, and the excess oxygen coefficient was maintained at 2.3. The results showed that as the ignition timing retards, CoVPmax and CoV(dp/dφ)max of argon power cycle engine increased, while CoVIMEP decreased firstly and increased afterward. And there is an ignition timing to make the lowest CoVIMEP, which is not consistent with MBT.
2017-10-08
Technical Paper
2017-01-2410
Ji Gao, Tie Wang, Dandan Sun, Jing Qiao, Yizhuo Feng
Abstract As the explosion proof diesel engine (EPD) of underground trackless tyred vehicle dynamic mechanical device, due to its good dynamic and economic performance, the diesel has been widely applied. The flame arrester can prevent the exhaust system from tempering, but the increased resistance will seriously affect the performance of diesel. Through the comparison of the CFD-FLUENT fluid simulation on flow and pressure field, the results show that the corrugated flame arrester performs better on reducing the exhaust back pressure than flat flame arrester and ensures the explosion-proof effect. The bench test of explosion proof diesel engine on intake and exhaust system is conducted, analysing the effect of the exhaust resistance under different speeds of diesel engine on the power, economy and emission of TY4100QFB type diesel engines with equivalent flow area , different specifications of flat versus corrugated flame-arrester in the course of external characteristics.
2017-10-08
Technical Paper
2017-01-2407
Michael Bardon, Greg Pucher, David Gardiner, Javier Ariztegui, Roger Cracknell, Heather Hamje, Leonardo Pellegrini, David Rickeard
Abstract Low Temperature Combustion using compression ignition may provide high efficiency combined with low emissions of oxides of nitrogen and soot. This process is facilitated by fuels with lower cetane number than standard diesel fuel. Mixtures of gasoline and diesel (“dieseline”) may be one way of achieving this, but a practical concern is the flammability of the headspace vapours in the vehicle fuel tank. Gasoline is much more volatile than diesel so, at most ambient temperatures, the headspace vapours in the tank are too rich to burn. A gasoline/diesel mixture in a fuel tank therefore can result in a flammable headspace, particularly at cold ambient temperatures. A mathematical model is presented that predicts the flammability of the headspace vapours in a tank containing mixtures of gasoline and diesel fuel. Fourteen hydrocarbons and ethanol represent the volatile components. Heavier components are treated as non-volatile diluents in the liquid phase.
2017-10-08
Technical Paper
2017-01-2408
Lei Zhou, Hongxing Zhang, Zhenfeng Zhao, Fujun Zhang
Abstract The Opposed Piston Two-Stroke (OPTS) engine has many advantages on power density, fuel tolerance, fuel flexibility and package space. A type of self-balanced opposed-piston folded-crank train two-stroke engine for Unmanned Aerial Vehicle (UAV) was studied in this paper. AVL BOOST was used for the thermodynamic simulation. It was a quasi-steady, filling-and-emptying flow analysis -- no intake or exhaust dynamics were simulated. The results were validated against experimental data. The effects of high altitude environment on engine performance have been investigated. Moreover, the matching between the engine and turbocharger was designed and optimized for different altitude levels. The results indicated that, while the altitude is above 6000m, a multi-stage turbocharged engine system need to be considered and optimized for the UAV.
2017-10-08
Technical Paper
2017-01-2457
Rickard Arvidsson, Tomas McKelvey
Abstract A two-state forward dynamic programming algorithm is evaluated in a series hybrid drive-train application with the objective to minimize fuel consumption when look-ahead information is available. The states in the new method are battery state-of-charge and engine speed. The new method is compared to one-state dynamic programming optimization methods where the requested generator power is found such that the fuel consumption is minimized and engine speed is given by the optimum power-speed efficiency line. The other method compared is to run the engine at a given operating point where the system efficiency is highest, finding the combination of engine run requests over the drive-cycle that minimizes the fuel consumption. The work has included the engine torque and generator power as control signals and is evaluated in a full vehicle-simulation model based on the Volvo Car Corporation VSIM tool.
2017-10-08
Technical Paper
2017-01-2456
Yun Li, Jing Shang, Shiwu Zhu, Alina Ma, Robin Lyle, Zijian Li, Nannan Wang, Hua Rong
Abstract This paper presents an Integrated Power Module (IPM) and an Integrated Power Unit (IPU) based on IGBT double-sided cooling technology. The IPU can be used as the motor controller in electric vehicle applications, and the IPM integrated in the IPU is packaged with the latest trench field-stop IGBT devices and is utilized with planar bonding as well as double-sided cooling technology. By adopting the planar bonding and double-sided cooling technology, module design has achieved elimination of the traditional wire bonds, even temperature distribution for the surface of dies, and improvement of thermal performance, which results in lower junction temperature rise. Through these factors, power cycling capability and long-time reliability of the module can be significantly improved. Test results show that compared with traditional single-sided direct liquid cooling module with a pin-fin structure, thermal resistance has been reduced by 23%.
2017-10-08
Technical Paper
2017-01-2462
Ruipeng Zhang, Kaichuang Meng
Abstract Due to the increase of mining production and rising labor costs, manufacturers of construction and mining equipment are engaged in developing large tonnage mining truck with good dynamic performance and high transport efficiency. This paper focuses on the improvement of the dynamic performance of a 52t off-highway dump truck. According to the characteristics of its operating cycle, electric auxiliary drive system is installed in the front axle aiming at improving the utilization rate of ground adhesion. The new all-wheel drive hybrid electric system makes it possible for dump truck transports at a higher velocity. Both the conventional dump truck model and the new all-wheel drive hybrid truck model are built based on the AVL-Cruise platform. Meanwhile, under the premise of enough dynamic performance, fuel consumption can be minimized by collaborative optimization in Isight.
2017-10-08
Technical Paper
2017-01-2460
Wenbin Liu, Qiang Song, Yiting Li, Wanbang Zhao
Abstract In this paper, a novel driver model is proposed to track vehicle speed in MIL (Model-in-the-Loop) test system, which has structural consistency with HIL (Hardware-in-the-Loop) test system. First, the MIL test system which contains models of driver, vehicle and test bench is established. Second, according to the connections of the established models in Matlab/Simulink environment, the vehicle speed is calculated in vehicle model. Emphatically, through the deviation between driving cycle speed and calculated vehicle speed, PI controller in driver model adjusts the vehicle speed to ideal point through sending the torque command to drive motor, the ILC (Iterative Learning Control) controller modifies and stores P value of PI controller. Then, in order to obtain the better modification of PI controller, iterative learning control algorithm is deeply researched in term of types and parameters.
2017-10-08
Technical Paper
2017-01-2464
Xinyou Lin, Chaoyu Wu, Qingxiang Zheng, Liping Mo, Hailin Li
Abstract The range-extended electric vehicle (REEV) is a complex nonlinear system powered by internal combustion engine and electricity stored in battery. This research proposed a Multiple Operation Points (MOP) control strategy of REVV based on operation features of REEV and the universal characteristic curve of the engine. The switching logic rules of MOP strategy are designed for the desired transition of the operation mode, which makes the engine running at high efficiency region. A Genetic algorithm (GA) is adapted to search the optimal solution. The fuel consumption is defined as the target cost function. The demand power of engine is defined as optimal variable. The state of charge (SOC) and vehicle speed are selected as the state variables. The dynamic performance of vehicle and cycling life of battery is set as the constraints. The optimal switching parameters are obtained based on this control strategy.
2017-10-08
Technical Paper
2017-01-2429
Felix Leach, Martin Davy, Adam Weall, Brian Cooper
Abstract Diesel engine designers often use swirl flaps to increase air motion in cylinder at low engine speeds, where lower piston velocities reduce natural in-cylinder swirl. Such in-cylinder motion reduces smoke and CO emissions by improved fuel-air mixing. However, swirl flaps, acting like a throttle on a gasoline engine, create an additional pressure drop in the inlet manifold and thereby increase pumping work and fuel consumption. In addition, by increasing the fuel-air mixing in cylinder the combustion duration is shortened and the combustion temperature is increased; this has the effect of increasing NOx emissions. Typically, EGR rates are correspondingly increased to mitigate this effect. Late inlet valve closure, which reduces an engine’s effective compression ratio, has been shown to provide an alternative method of reducing NOx emissions.
2017-10-08
Technical Paper
2017-01-2430
Yingmin Wang, Tao Cui, Fujun Zhang, Sufei Wang, Hongli Gao
Abstract Considering the randomness and instability of the oil pressure in the lubrication system, a new approach for fault detection and diagnosis of diesel engine lubrication system based on support vector machine optimized by particle swarm optimization (PSO-SVM) model and centroid location algorithm has been proposed. Firstly, PSO algorithm is chosen to determine the optimum parameters of SVM, to avoid the blindness of choosing parameters. It can improve the prediction accuracy of the model. The results show that the classify accuracy of PSO-SVM is improved compared with SVM in which parameters are set according to experience. Then, the support vector machine classification interface is fitted to a curve, and the boundary conditions of fault diagnosis are obtained. Finally, diagnose algorithm is achieved through analyzing the centroid movement of features. According to Performance degradation data, degenerate trajectory model is established based on centroid location.
2017-10-08
Technical Paper
2017-01-2432
Xiangwang Li, Weimin Wang, Xiongcai Zou, Zhiming Zhang, Wenlong Zhang, Shemin Zhang, Tao Chen, Yuhuang Cao, Yuanda Chen
Abstract In order to reduce emissions, size and manufacturing cost, integrated exhaust manifold become popular in gasoline engine, especially in three-cylinder engine. Moreover, due to shorter length, lighter weight, and less component connections, the exhaust manifold and hot end durability will improve apparently. In this work, an advanced cylinder head with integrated exhaust manifold is adopted in a three-cylinder turbo engine. Because of this integration characteristic, the gas retain in cylinder head longer and the temperature reach higher level than normal cylinder head, which will cause thermal fatigue failure more easily. To validate the exhaust manifold and hot end durability, series simulation and test validation work have been done. Firstly, overall steady state and transient temperature simulation was done for global model. For turbocharger, in order to simulate the outlet turbulent flow and 3d rotation, a code was compiled to define this 3d rotation.
2017-10-08
Technical Paper
2017-01-2433
Fengqin Huang, Wenxin CAI, Zhiming Zhang, Wenlong Zhang, Laifeng Shi, Xin Li, Bernhard Kaltenegger, Daniele Suzzi, Werner Schrei, Karl Weihrauch
Abstract Nowadays high thermal efficiency engine is the mainstream of the gasoline engine development, and the control of the design period is strict, which lead to the cylinder head design become more and more difficult. How to get the optimal design of cylinder head quickly is an important research topic by design professionals in the current, which not only meets the performance requirements, but also guarantees the requirement of reliability. The sub-model method is high efficient and high precision in solving the complex problem of stress and strain, which widely used in truss, road, bridge and large container. Using this technology in the local structure optimization of the cylinder head, will shorten the cycle of structure optimization significantly, and get the optimal design of cylinder head quickly. In this paper, Firstly, the cylinder head global FE model was set up.
2017-10-08
Technical Paper
2017-01-2435
Jian Ji, BoZhou He, Lei Yuan
Abstract It is well-known that, compared with automatic transmissions (ATs), continuously variable transmission (CVT) shows advantages in fuel saving due to its continuous shift manner, since this feature enables the engine to operate in the efficiency-optimized region. However, as the AT gear number increases and the ratio gap narrows, this advantage of CVT is challenged. In this paper, a comparative study on fuel economy for a CVT based vehicle and a 9-speed automatic transmission (AT) based vehicle is proposed. The features of CVT and AT are analyzed and ratio control strategies for both the CVT and 9-speed AT based vehicles are designed from the view point of vehicle fuel economy, respectively. For the 9-speed AT, an optimal gear shift map is constructed. With this gear shift map, the optimal gear is selected as vehicle velocity and driving condition vary.
2017-10-08
Technical Paper
2017-01-2437
Renjith S, Vinod Kumar Srinivasa, Umesh Venkateshaiah
Abstract The jet lubrication method is extensively used in the constant mesh high performance transmission system operating at range of speeds though it affects mechanical efficiency through spin power loss. The lubrication jet has a key role to maintain the meshing gears at non-fatal thermal equilibrium by effectively dissipating the heat generated to the surrounding. Heat transfer coefficient (HTC) is the indicator of the thermal behavior of the system, which provides great insight of efficient lubrication system that needs to be employed for prescribed type of transmission. In this study, a segment of the transmission unit which constitutes a gear pair is used for the simulation. Parametric study is carried out by considering the critical parameters affecting the thermal performance such as lubrication jet flow rate and rotational motions of the gears with speeds and temperatures.
2017-10-08
Technical Paper
2017-01-2439
Srinivasan Paulraj, Saravanan Muthiah
Abstract Poor clutch life is a major issue for some light commercial vehicle models. Clutch overheating is the primary cause for clutch failure. Some of the reasons include inappropriate gear selection by the driver, poor low-end dynamic torque availability from an engine, heavy stop and go traffic, vehicle overloading resulting in excessive clutch slippage especially in gradients, riding of the clutch pedal by the customer etc. These situations lead to a high thermal energy dissipation at the clutch, increasing clutch wear and in extreme conditions leading to not only poor shift quality but also eventual clutch failure. Unfortunately, it is not practical to monitor clutch temperature in a production vehicle due to high costs or technical challenges involved. This paper describes 1-D thermal modeling of single plate dry clutch typically used in passenger car/truck and bus applications.
2017-10-08
Technical Paper
2017-01-2441
Zhao Ding, Li Chen, Chengliang Yin, Jian Yao, Chunhao Lee, Farzad Samie
Abstract Rotating clutches play an important role in automatic transmissions (AT), dual-clutch transmissions (DCT) and hybrid transmissions. It is very important to continually improve the transmission systems in the areas such as simplifying actuator designs, reducing cost and increasing controllability. A new concept of electrical motor driven actuation using a wedge mechanism, a wedge clutch, demonstrates potential benefits. This wedge clutch has the characteristics of good mechanical advantage, self-reinforcement, and faster and more precise controllability using electrical motor. In this paper, a new rotating wedge clutch is proposed. It presents a challenge since the motor actuator has to be stationary while the clutch piston is rotating. A new mechanism to connect the motor to the wedge piston, including dual-plane bearings and two mechanical ramp linkages, is studied. The design and verification of the physical structure of the actuator are discussed in detail in the paper.
2017-10-08
Technical Paper
2017-01-2442
Bingqing Xiao, Wei Wu, Jibin Hu, Shihua Yuan, Chenhui Hu
Abstract The prediction of temperature distribution and variation of oil-cooled sliding disk pair is essential for the design of wet clutches and brakes in a vehicle transmission system. A two-phase coupled heat transfer model is established in the study and some fluid-solid coupled heat transfer simulations are performed to investigate the thermal behaviors of wet clutch during sliding by CFD method. Both cooling liquid and grooved solid disks are contained in the heat transfer model and the heat convection due to the cooling liquid in the radial grooves is also considered by fluid-solid coupled transient heat transfer simulations. The temperature distribution and variation of the grooved disk are discussed and analyzed in detail. The results indicate that the temperature distribution on the grooved disk is nonuniform. The temperature within the middle radius area is higher than that in the inner and outer radius area.
2017-10-08
Technical Paper
2017-01-2443
Ziwang Lu, Hongxu Chen, Lijun Wang, Guangyu Tian
Abstract During the engaging process of sleeve and teeth ring in mechanical transmissions, their rotational speed and position differences cause multiple engaging ways and trajectories, and casual impacts between them will delay the engaging process and cause a long power off time for a gear shift. In order to reveal the engaging mechanism of the sleeve and the teeth ring, it is essential to build a high-fidelity model to cover all of their engaging ways and capture their speed changes for an impact. In this work, our contribution is that their impact process is modeled as a precise, continuous and nonlinear damping model, and then a hybrid automaton model is built to connect the system dynamics in different mechanical coupling relationships.
2017-10-08
Technical Paper
2017-01-2444
Yanzhong Wang, Guanhua Song
Abstract High-speed rotating gears are generally lubricated by spray lubrication. Lubricating oil is driven by high-speed rotating gear, and some lubricating oil will be excited into oil mist, so that the gears are in the gas-liquid mixed environment. In this paper, the computational fluid dynamics model of the spray lubrication cooling process is established based on the gear heat transfer behavior under the spray lubrication condition. The influence of different spray parameters on the liquid-solid two-phase convective heat transfer coefficient is obtained. On this basis, the accurate boundary conditions of gear temperature field calculation are analyzed by studying the heat transfer behavior of high speed gear spray lubrication. The calculation model of gear temperature based on spray lubrication is established, and the temperature field distribution of gear is obtained.
2017-10-08
Technical Paper
2017-01-2333
Marcos Gutierrez, Andres Castillo, Juan Iniguez, Gorky Reyes
Abstract Aiming for cleaner and more efficient energy from the internal combustion engines makes necessary to ensure the special conditions for exploitation of alternative fuels. The engine vibrations are primarily understood as effects of mechanical failures, but they are also a subject of the fuel combustion effects. These effects depend on the fuel type and its ability to complete the combustion process. The vibrations of a diesel engine were measured and analyzed with a frequency spectrum calculated with fast Fourier transforms. The engine was operated with a fuel blend of 10 % recycled lubricating oil with 90% diesel fuel as well as with neat diesel. It was found that the engine operation with this fuel blend has a lower vibration level in comparison with the use of neat diesel fuel. The goal of this research is to determine the properties of the fuel blend, which provide more stability to the engine by means of vibrations reduction.
2017-10-08
Technical Paper
2017-01-2252
Weihua Sun, Wei Du, Xuefei Dai, Xiangdong Bai, Zhiping Wu
Abstract The acquisition of more authentic cylinder pressure data is the basis of engine combustion analysis. Due to the multiple advantages, quartz piezoelectric pressure transducers are generally applied to the measurement of the cylinder pressure. However, these transducers can only produce dynamic cylinder pressure data which may be significantly different from the actual values. Thus, the cylinder pressure data need to be corrected through a certain method, while different cylinder pressure correction methods will cause result divergences of the combustion analysis. This paper aims to acquire a proper cylinder pressure correction method by carrying out theoretical analysis based on the polytropic process in the compression stroke as well as the experimental research of the cylinder pressure of a turbocharged eight-cylinder diesel engine.
2017-10-08
Technical Paper
2017-01-2283
Anand Prabu Kalaivanan, Gnanasekaran Sakthivel
Abstract Electronic Fuel Injection Systems have revolutionised Fuel Delivery and Ignition timing in the past two decades and have reduced the Fuel Consumption and Exhaust Emissions, ultimately enhancing the Economy and Ecological awareness of the engines. But the ignition/injection timing that commands the combustion is mapped to a fixed predefined table which is best suited during the stock test conditions. However continuous real time adjustments by monitoring the combustion characteristics prove to be highly efficient and be immune to varying fuel quality, lack of transient performance and wear related compression losses. For developing countries, Automotive Manufacturers have been Tuning the Ignition/Injection timing Map assuming the worst possible fuel quality. Conventional knock control system focus on engine protection only and doesn't contribute much in improving thermal efficiency.
2017-10-08
Technical Paper
2017-01-2318
Xiaoxu Jia, Zhong Huang, Dehao Ju, Zhen Huang, Xing-cai Lu
Abstract Combustion instability often occurs inside the combustion chamber of aero engine. Fuel atomization and evaporation, one of the controlling processes of combustion rate, is an important mechanism of the combustion instability. To tackle combustion instability, it challenges a deep understanding of the underlying mechanism of fuel atomization and evaporation. In this paper, acoustic field was established to simulate the pressure oscillation. Transient spray images of ethanol and kerosene were recorded using high-speed camera. The obtained images were processed by MATLAB to extract and analyze the related data. Spatial fuel atomization characteristics was analytically examined by multi-threshold image method to analyze the effect of the high frequency acoustic field on the fuel break-up and disintegration. The results show that the half spray cone angle on the side with speaker is suppressed by the presence of the imposed acoustic field compared with the case without speaker.
Viewing 151 to 180 of 44126