Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 3456
2017-12-01
WIP Standard
AMS3021F
This specification covers a neopentyl polyol ester fluid.
2017-11-30
WIP Standard
ARP5316E

This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life.

The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents.

CURRENT
2017-11-29
Standard
AMS3731/10C
This specification covers an unfilled, room-temperature-polymerizing epoxy resin formulation with a polyamide hardener, supplied as a two-component system.
CURRENT
2017-11-21
Standard
AMS3329C
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
CURRENT
2017-11-21
Standard
AMS3330C
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
CURRENT
2017-11-21
Standard
AS6294/1
This document establishes common industry practices and recommended screening, qualification, and lot acceptance testing of Plastic Encapsulated Microcircuits (PEMs) for use in space application environments.
CURRENT
2017-11-21
Standard
AS5316
This SAE Aerospace Standard (AS) specifies the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components.
CURRENT
2017-11-20
Standard
AMS3382D
This specification covers two classes (durometers) of tetrafluoroethylene/propylene rubber (FEPM) in the form of extrusions, sheet, strip, and molded shapes. These products have been used typically for components requiring continuous operation in dry air, hydraulic fluids, and synthetic engine oils at temperatures from -5 to +232 ° C (+23 to 450 ° F) or in high pH chemical decontamination solutions, but usage is not limited to such applications.
CURRENT
2017-11-20
Standard
AMS3331C
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
2017-11-13
WIP Standard
AMS6562/4
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the fourth detail spec.
2017-11-13
WIP Standard
AMS6562/5
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the fifth detail spec.
2017-11-13
WIP Standard
AMS6562/6
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the sixth detail spec.
2017-11-10
WIP Standard
AMS6567/1
AMS6567 The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is designed specifically for vacuum-bag-only cure, with an initial low temperature cure followed by a higher temperature post-cure. This material is intended for use in laminate applications with a service temperature up to 250 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6567/2
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is designed specifically for vacuum-bag-only cure, with an initial low temperature cure followed by a higher temperature post-cure. This material is intended for use in laminate applications with a service temperature up to 250 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6569/1
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. These materials are designed specifically for vacuum bag autoclave cure. These materials are intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6569/2
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. These materials are designed specifically for vacuum bag autoclave cure. These materials are intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6568/3
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6568/2
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness.
2017-11-10
WIP Standard
AMS6568/1
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness. This is the base specification and it will have three slash/detail specs.
2017-11-10
WIP Standard
AMS6566/1
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness. This is the base specification and it will have one slash/detail specs.
2017-11-09
WIP Standard
AMS6562/2
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the second detail spec.
2017-11-09
WIP Standard
AMS6562/1
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the first slash/detail spec.
2017-11-09
WIP Standard
AMS6562/3
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the third detail spec.
2017-11-08
WIP Standard
AMS6569
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. These materials are designed specifically for vacuum bag autoclave cure. These materials are intended for use in laminate applications with a service temperature up to 180 °F. They are typically used in structural applications requiring high strength and stiffness. This is the base specification and it will have two slash/detail specs.
2017-11-08
WIP Standard
AMS6567
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is designed specifically for vacuum-bag-only cure, with an initial low temperature cure followed by a higher temperature post-cure. This material is intended for use in laminate applications with a service temperature up to 250 °F. They are typically used in structural applications requiring high strength and stiffness. This is the base specification and it will have two slash/detail specs.
2017-11-08
WIP Standard
AMS6565
Establish a new AMS for dry carbon fabric for Hexcel SGP196P IM7 plain weave fabric.
2017-11-08
WIP Standard
AMS6562
The purpose of this specification is to allow procurement of a defined material corresponding to statistically derived material properties published in CMH-17. This material is intended for use in laminate applications with a service temperature up to 250 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. This is the basic spec and it will have three slash/detail specs.
Viewing 1 to 30 of 3456

Filter

  • Standard
    3456