Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 150
2017-08-18
WIP Standard
ARP6903A
The intent of this ARP is to provide guidance to assist users in choosing compatible component finishes/platings to achieve the best corrosion resistance performance for compatible components/couples. This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. A galvanic compatibililty table is provided to assist with the compatible plating/finish selection. Specific plating performance parameters for each individual plating and each connector/accessory specification have also been provided to assist the product user with compatible plating/finish selection.
CURRENT
2017-07-26
Standard
AMS2428
This specification covers the requirements for electrodeposited nanocrystalline cobalt-phosphorus plating.
CURRENT
2017-07-18
Standard
AMS2404H
This specification covers the requirements for electroless nickel deposited on various materials.
CURRENT
2017-07-14
Standard
AIR5479B
This SAE Aerospace Information Report (AIR) describes the performance of plating’s and coatings for landing gear that potentially provide environmental compliance benefits versus the current baseline processes. The hazardous systems addressed in this version of the document include cadmium plating, chromated primers, and high VOC (volatile organic compounds) topcoats. The AIR applies to landing gear structures and mechanisms for all types of civil and military aircraft. The potential replacements apply to both Original Equipment Manufacturer (OEM) hardware and overhaul of in-service landing gears.
2017-06-22
WIP Standard
AMS2451/3C
This specification covers the requirements for brush plating of low-hardness, low-stress nickel by electrodeposition.
2017-06-22
WIP Standard
AMS2451/4D
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-06-20
Standard
AMS4315A
This specification covers an aluminum alloy in the form of sheet and plate up to 2.000 inch (54.80 mm) inclusive, in thickness (see 8.5).
CURRENT
2017-06-16
Standard
AMS4200C
This specification covers an aluminum alloy in the form of plate.
CURRENT
2017-06-15
Standard
AMS4046G
This specification covers an aluminum alloy in the form of sheet and plate clad on one side.
CURRENT
2017-06-08
Standard
AS7109/6B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/6. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/6. Cancelled specifications are available from SAE.
CURRENT
2017-05-25
Standard
AMS4036L
This specification covers an aluminum alloy in the form of sheet and plate clad on one side with a different aluminum alloy.
CURRENT
2017-05-18
Standard
AIR6130A
14-day material test to determine the cyclic effects of runway deicing compounds on cadmium plated parts.
CURRENT
2017-04-24
Standard
AMS4303C
This specification covers an aluminum alloy in the form of plate.
CURRENT
2017-04-14
Standard
AMS2451/5B
This specification covers the requirements for brush plating of hard chromium by electrodeposition.
CURRENT
2017-04-14
Standard
AMS2451/1B
This specification establishes the requirements for a general-purpose brush plating of nickel applied by electrodeposition.
CURRENT
2017-04-11
Standard
AMS2451/8B
This specification covers the requirements for brush plating of non-cyanide silver by electrodeposition.
CURRENT
2017-04-11
Standard
AMS2451/7B
This specification covers the requirements for brush plating of medium-hardness, low stress nickel by electrodeposition.
CURRENT
2017-04-06
Standard
AMS4599A
This specification covers an aluminum alloy in the form of sheet and plate from 0.020 to 6.000 inches (0.51 to 152.40 mm), inclusive, in thickness (see 8.5).
CURRENT
2017-04-06
Standard
AMS4613A
This specification covers an aluminum alloy in the form of sheet and plate from 0.020 to 5.000 inches (0.51 to 127.00 mm), inclusive, in thickness (see 8.5).
CURRENT
2017-04-04
Standard
AMS4501F
This specification covers one type of copper in the form of sheet, strip, and plate.
CURRENT
2017-03-28
Standard
AMS4939C
This specification covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.60 mm) nominal thickness.
CURRENT
2017-03-24
Standard
AMS5085J
This specification covers a carbon steel in the form of sheet, strip, and plate.
CURRENT
2017-03-17
Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-03-17
Standard
ARP6903
The intent of this ARP is to provide guidance to assist users in choosing compatible component finishes/platings to achieve the best corrosion resistance performance for compatible components/couples. This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. A galvanic compatibililty table is provided to assist with the compatible plating/finish selection. Specific plating performance parameters for each individual plating and each connector/accessory specification have also been provided to assist the product user with compatible plating/finish selection.
CURRENT
2017-03-08
Standard
AMS2418J
This specification covers the requirements for electrodeposited copper.
CURRENT
2017-03-07
Standard
AMS4473A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch (19.05 to 38.10 mm), inclusive, in nominal thickness.
CURRENT
2017-02-27
Standard
AMS2451/14
This specification covers the requirements for brush plating of nickel-tungsten by electrodeposition.
CURRENT
2017-02-13
Standard
AMS4472A
This specification covers an aluminum alloy in the form of plate 0.500 to 2.250 inch (12.70 to 57.15 mm) in nominal thickness (see 8.5).
CURRENT
2017-01-05
Standard
AMS6435G
This specification covers a premium aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
Viewing 1 to 30 of 150

Filter

  • Standard
    150