Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 57
CURRENT
2017-09-13
Standard
J2597_201709
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
2017-08-24
WIP Standard
J444
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches , preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
CURRENT
2017-08-18
Standard
J443_201708
This SAE Recommended Practice Specification provides the procedures for using test strips per SAE J442 for peening processes.
CURRENT
2017-08-09
Standard
J442_201708
This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
2017-05-10
WIP Standard
J1173
This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers. The glass bead classification number is the approximate nominal diameter of the glass spheres in that classification, in hundredths of a millimeter, with the prefix GB added. Glass beads used for peening shall be made from high quality glass of the soda-lime type. They should be as resistant as possible to breakage from shock-impact, or by abrasion during shipment and handling. The particles should be substantially round, free-flowing, and free from chemical impurities or contaminants that might be detrimental to the workpiece.
CURRENT
2016-11-15
Standard
AMS2590A
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic Almen test strip holder is required for intensity determination.
2015-07-17
WIP Standard
AMS2430U
This specification covers the requirements for automatic shot peening of surfaces of parts by impingement of media, including metallic, glass, or ceramic shot.
CURRENT
2015-06-30
Standard
J2441_201506
This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot.
CURRENT
2015-06-18
Standard
J2175_201506
This SAE Recommended Practice describes chemical analysis, hardness, microstructure, and physical characteristic requirements for low carbon cast steel shot to be used for shot peening or blast cleaning operations.
CURRENT
2015-01-28
Standard
AMS2430T
This specification covers the requirements for automatic shot peening of surfaces of parts by impingement of media, including metallic, glass, or ceramic shot.
CURRENT
2013-10-16
Standard
J1830_201310
This specification covers characteristics for chemistry, microstructure, density, hardness, size, shape and appearance of zirconium oxide based ceramic shot, suitable for peening surfaces of parts by impingement.
CURRENT
2013-10-16
Standard
J827_201310
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
CURRENT
2013-10-16
Standard
J441_201310
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
CURRENT
2013-08-21
Standard
J445_201308
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
CURRENT
2013-07-24
Standard
AMS2585A
The complete requirements for procuring the product shall consist of this document and the latest Issue of the basic specification, AMS2431.
CURRENT
2013-06-11
Standard
AMS2580A
This specification covers the requirements for inducing compressive residual stresses on the surface of metal parts using ultrasonically activated shot peening.
CURRENT
2013-04-24
Standard
J2277_201304
This SAE recommended practice provides some procedure for determining shot peening coverage and relating coverage to part exposure to the media stream. Effectiveness of shot peening is directly dependent on coverage. Either incomplete or excessive coverage can be detrimental to fatigue strength and life.
HISTORICAL
2013-02-18
Standard
J442_201302
This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
CURRENT
2012-09-17
Standard
J444_201209
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
HISTORICAL
2010-06-16
Standard
J443_201006
This SAE Recommended Practice provides uniform procedures for using the standard shot peening Almen strips reported in SAE J442. Standard Almen strips are used to establish saturation, determine intensity, monitor repeatability of the shot peening machine operations, and can be used to predict a desired result on a part. It is recommended that the standard Almen strip A be used for intensities that produce arc heights of 0.10 mm A (0.004 in A) to 0.60 mm A (0.024 in A). For intensities below 0.10 mm A (0.004 in A), the standard N strip is recommended, and for intensities above 0.60 mm A (0.024 in A), the standard C strip is recommended. Use of SAE 2597 Computer Generated Shot Peening Saturation Curves is voluntary, existing shot peening processes that do not take advantage of computer generated saturation curves need not be changed to meet the requirements listed herein.
HISTORICAL
2010-06-16
Standard
J444_201006
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches, preceded by an S. For grit, this number corresponds with sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
HISTORICAL
2010-05-17
Standard
AMS2585
The complete requirements for procuring the product shall consist of this document and the latest Issue of the basic specification, AMS2431.
HISTORICAL
2010-05-17
Standard
AMS2580
This specification covers the requirements for inducing compressive residual stresses on the surface of metal parts using ultrasonically activated shot peening.
HISTORICAL
2010-01-14
Standard
J2597_201001
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
HISTORICAL
2009-11-09
Standard
J441_200911
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
HISTORICAL
2009-10-26
Standard
J2277_200910
This SAE Recommended Practice provides procedures for determining shot peening coverage. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage may be detrimental to fatigue strength and life.
HISTORICAL
2008-11-24
Standard
J442_200811
This SAE Standard defines requirements for equipment/supplies to be used in measuring shot peening intensity. Guidelines for the use of these articles (test strip, holding fixture, and gage) are also included.
HISTORICAL
2006-05-22
Standard
J442_200605
This SAE Standard defines requirements for equipment/supplies to be used in measuring shot peening intensity. Guidelines for the use of these articles (test strip, holding fixture, and gage) are also included.
HISTORICAL
2005-07-25
Standard
J827_200507
This SAE Recommended Practice describes chemical composition, and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
HISTORICAL
2005-07-25
Standard
J445_200507
This SAE Information Report is intended to provide users and producers of metallic shot and grit with general information on methods of mechanically testing metal shot in the laboratory.
Viewing 1 to 30 of 57

Filter

  • Standard
    57