Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 14536
2017-07-24
WIP Standard
ARP5483/2A
This method outlines the standard procedure for testing the hardness of bearing components. Bearings covered by this test method shall be any rolling element bearing used in airframe control.
CURRENT
2017-07-20
Standard
J995_201707
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
2017-07-19
WIP Standard
J1939DA_201707
This document is intended to supplement the J1939 documents by offering the J1939 information in a form that can be sorted and search for easier use. The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. It also includes the supporting descriptions and figures previously published in the SAE J1939-71 document.
2017-07-19
WIP Standard
AS5420G
This SAE Aerospace Standard (AS) covers the requirements for a flexible, lightweight, low pressure, self-extinguishing, integrally heated silicone hose assembly. The hose has a fully fluorinated fluoropolymer inner liner and is primarily intended for use in aircraft potable water systems with an environmental operating temperature range of -65 °F (-54 °C) to +160 °F (+71 °C).
2017-07-17
WIP Standard
AS7473C
This procurement specification covers bolts and screws made from carbon steels, high expansion steels, or corrosion and heat resistant steels of the type identified under the Unified Numbering System as follows: a. UNS K00802 - carbon steel (AMS 5061) b. UNS K91505 - high expansion steel (AMS 5624) c. UNS K91456 - high expansion steel (AMS 5625) d. UNS S32100 - corrosion and heat resistant steel (AMS 5645) e. UNS S34700 - corrosion and heat resistant steel (AMS 5646)
2017-07-17
WIP Standard
AS7474D
This specification covers bolts and screws made from a corrosion and heat resistant, martensitic iron base alloy of the type identified under the Unified Numbering System as UNS S17400. The following specification designations and their properties are covered: AS7474 140 ksi minimum ultimate tensile strength at room temperature 100 ksi stress corrosion test 72 ksi to 7.2 ksi tension-tension fatigue; AS7474-1 140 ksi minimum ultimate tensile strength at room temperature 100 ksi stress corrosion test 88 ksi minimum ultimate shear strength at room temperature.

Primarily for aerospace propulsion system applications where corrosion resistance and high strength in tension is required in temperatures not to exceed 600 °F.

2017-07-17
WIP Standard
MA3375D
This document covers metric studs made from a corrosion and heat resistant, age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286. The following specification designations and their properties are covered: MA3375 900 MPa minimum ultimate tensile strength at room temperature MA3375-1 900 MPa minimum ultimate tensile strength at room temperature 480 MPa stress-rupture strength at 650 °C MA3375-2 900 MPa minimum ultimate tensile strength at room temperature 590 MPa minimum ultimate shear strength at room temperature
CURRENT
2017-07-17
Standard
AMS3255B
This specification establishes the requirements for an expanded polytetrafluoroethylene (EPTFE) in the form of sealing tape, gaskets, or sheets requiring no mixing or curing.
CURRENT
2017-07-14
Standard
J1754/1_201707
This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See Part 2, Table 7 for hose operating temperature ranges and identification codes. NOTE: Working pressure is defined as maximum system pressure.
CURRENT
2017-07-13
Standard
J1717_201707
SAE J1717 is an advisory document suggesting minimum recommended testing, appearance evaluation, and protocol for specifying the recommendations with regard to Singular Unassembled Automotive Interior Trim Parts.
CURRENT
2017-07-11
Standard
AS6449C
This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a temperature range of -90 to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.
2017-07-11
WIP Standard
AMS3217/8A
This specification covers a high temperature, compression set and fluid resistant fluorocarbon (FKM) rubber stock in the form of molded test slabs. Material has improved low temperature sealing (-30°C Tg) and improved compatibility to a variety of advanced gas turbine engine oils (HTS-type). In application, these reference slabs would be an extension of AMS 3217A (Standard Elastomer Stocks) - AMS 3217/8A is proposed.
2017-07-11
WIP Standard
AS1650E
This SAE Aerospace Standard (AS) defines the requirements for a threadless, flexible, self-bonding coupling assembly which, when installed on machined fixed cavity ferrules, provides a flexible connection for joining tubing and components in aircraft fuel, vent or other systems. This assembled coupling, hereafter referred to as the assembly, and is designed for use from -65 to +400 °F and at 125 psig nominal operating pressure.
2017-07-11
WIP Standard
J1731
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
2017-07-11
WIP Standard
J1134
This SAE Recommended Practice establishes a single bolt pattern for the No. 1 clutch housing (see Figure 1) and the No. 2 clutch housing (see Figure 2). These four bolt patterns are designated to give commonality of mounting brackets in existing frame rails. The 420 mm (16.5 in) span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate commonly used clutches.
CURRENT
2017-07-10
Standard
AS1650D
This SAE Aerospace Standard (AS) defines the requirements for a threadless, flexible, self-bonding coupling assembly which, when installed on machined fixed cavity ferrules, provides a flexible connection for joining tubing and components in aircraft fuel, vent or other systems. This assembled coupling, hereafter referred to as the assembly, and is designed for use from -65 to +400 °F and at 125 psig nominal operating pressure.
CURRENT
2017-07-07
Standard
AS7974/5A
SCOPE IS UNAVAILABLE.
CURRENT
2017-07-07
Standard
AS21905D
Scope unavailable.
CURRENT
2017-07-07
Standard
AS14238D
SCOPE IS UNAVAILABLE.
CURRENT
2017-07-07
Standard
AS85848/2A
SCOPE IS UNAVAILABLE.
CURRENT
2017-07-07
Standard
AS4696B
No scope available.
CURRENT
2017-07-07
Standard
AS81714/10A
Scope not available.
CURRENT
2017-07-07
Standard
AS21910E
Scope unavailable.
Viewing 1 to 30 of 14536

Filter

  • Standard
    14536