Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 212
2017-03-29
WIP Standard
J2743
This SAE Recommended Practice is intended to describe a procedure for rating the size of single-stage reciprocating air compressors. It describes the conditions that can be used for testing and it defines a standardized rating expressed in SLPM (SCFM).
CURRENT
2017-02-09
Standard
J1883_201702
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
CURRENT
2017-02-08
Standard
J2337/2_201702
This part of SAE J2337 specifies dimensions, design, and performance requirements for eight connectors using a conical seal to insure leak proof performance with a design factor of 4 to 1.
CURRENT
2017-02-08
Standard
J533_201702
This SAE Standard covers specifications and performance requirements for 37° and 45° single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8434-2 connectors. The flares described in this document are intended for use with SAE metallic tube materials. Considerations such as the effects of wall thickness selection for specific working pressures, identifying appropriate length of thread engagements for specific applications with mating connectors and other associated criteria, shall be the responsibility of the user. For applicable nominal reference working pressures for hydraulic tubing, see SAE J1065 and ISO 10763.
CURRENT
2016-12-20
Standard
J1942/1_201612
The following list consists of hose data provided as of December 2016, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: Successfully test their hose to the requirements of SAE J1942, Table 1. Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results. All sizes should be included in the same letter which must also include all of the information necessary to make a SAE J1942-1 listing.
CURRENT
2016-12-06
Standard
J1939/11_201612
This document defines a physical layer having a robust immunity to EMI and physical properties suitable for harsh environments. CAN controllers are available which support the CAN Flexible Data Rate Frame Format. These controllers, when used on SAE J1939-11 networks, must be restricted to use only the Classical Frame Format compliant to ISO 11898-1:2015. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
CURRENT
2016-11-30
Standard
J3096_201611
This SAE Recommended Practice was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications. It addresses Non-Metallic caps and both Metallic and Non-Metallic filler necks.
CURRENT
2016-11-15
Standard
J1294_201611
This SAE Recommended Practice covers distributors used on marine engines. NOTE: This includes devices referred to as high voltage switches used for distributing high voltage to the appropriate spark plugs but does not contain any crank position sensing function.
HISTORICAL
2016-11-03
Standard
J1939DA_201611
This document is intended to supplement the J1939 documents by offering the J1939 information in a form that can be sorted and search for easier use. The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. It also includes the supporting descriptions and figures previously published in the SAE J1939-71 document.
CURRENT
2016-08-23
Standard
J2956_201608
This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J3044_201608
This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J2917_201608
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-02
Standard
J1163_201608
This SAE Standard specifies a method and the device for use in determining the position of the Seat Index Point (SIP) for any kind of seat.
CURRENT
2016-08-02
Standard
J1231_201608
This SAE Standard provides general and dimensional specifications for formed tube ends and hose fittings. These connections are intended for general applications in low pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown in Figures 2 and 3 are intended to be retained by hose clamps as specified in SAE J1508. It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
CURRENT
2016-07-20
Standard
J1410_201607
This SAE Recommended Practice establishes minimum performance requirements for new pneumatic valves when tested in accordance with the test procedure outlined in SAE J1409. The performance requirements will include: Input-output performance Leakage characteristics Low temperature performance Elevated temperature performance Corrosion resistance performance Endurance testing Structural integrity
CURRENT
2016-07-12
Standard
J553_201607
This SAE Standard defines the test conditions, procedures, and performance requirements for circuit breakers in ratings up to and including 200 A. The document includes automatic reset, modified reset, and manually reset types of circuit breakers for 12 V and 24 V DC electrical systems. Some circuit breakers may have dual voltage ratings (AC and DC), however, this document evaluates DC performance only.
CURRENT
2016-07-01
Standard
J1865_201607
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 inch, 22.5 inch, and 24.5 inch diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The lines provided establish the maximum envelope for brakes, including all clearances, and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
CURRENT
2016-06-30
Standard
J2270_201606
This SAE Standard covers both quality assurance and installation requirements for fasteners. This document establishes engineering criteria and guidance for quality assurance requirements (including Test and Inspection) for procurement of threaded fasteners where such criteria and guidance is not otherwise provided by existing fastener standards or specifications. The document also provides requirements and test procedures for self-locking fasteners including those manufactured by the installing activity. This document also provides requirements for the selection and use of fastener lubricants, additional corrosion protection treatments, fastener tightening procedures, and the use of thread-locking compounds.
CURRENT
2016-06-17
Standard
J1861_201606
This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: Crack (opening) pressure or force. Crack pressure may be measured at the initial output pressure or as the pressure differential before output pressure exceeds 14 kPa (2 psi). Crack force may be measured at initial output pressure or before output pressure exceeds 14 kPa (2 psi). Pressure differential (input-output)
CURRENT
2016-06-14
Standard
J1860_201606
This SAE Recommended Practice applies to those air brake system valves used to control the vehicle service brakes and test procedures defined by SAE J1859 to measure performance characteristics. This Recommended Practice adheres to standard industry practice of using English units for specifying valve characteristics.
CURRENT
2016-06-14
Standard
J1859_201606
This SAE Recommended Practice establishes uniform test procedures for determining input-output characteristics for those pilot-operated and mechanically actuated, modulating-type valves and through-type valves used in the service brake control system.
CURRENT
2016-05-20
Standard
J371_201605
This SAE Recommended Practice applies to off-road, self-propelled work machine categories of earthmoving, forestry, road building and maintenance, and specialized mining machinery as defined in SAE J1116.,
2016-05-10
WIP Standard
J1817
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
CURRENT
2016-04-01
Standard
J2800_201604
This lab test procedure should be used when evaluating the combined corrosion and fatigue performance for a particular coating system, substrate, process and design. The test is intended to provide an A to B comparison of a proposed coil spring design versus an existing field validated coil spring when subjected to the combined effects of corrosion and fatigue. The corrosion mechanisms covered by this test include general, cosmetic and pitting corrosion. Fatigue testing covers the maximum design stress and/or stress range of the coil spring design (typically defined as excursion from jounce to rebound positions in a vehicle). The effects of gravel and heat are simulated by pre-conditioning the springs prior to fatigue testing. Time dependant corrosion mechanisms such as stress corrosion cracking are not addressed with this test.
CURRENT
2016-03-30
Standard
J2549_201603
This SAE standard establishes the minimum construction and performance requirements for single conductor cable for use on trucks, trailers and converter dollies.
CURRENT
2016-03-15
Standard
J1817_201603
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
CURRENT
2015-11-24
Standard
J3082_201511
This SAE Standard provides the minimum requirements for high power two conductor jumper cable plug and receptacle for truck-trailer jumper cable systems. It includes the test procedures, design, and performance requirements. This document covers receptacles rated at more than 30A (Ampere) up to and including 150A and is intended for a single circuit with one power conductor and one common return conductor. Single conductor high current connectors are not recommended for future designs because of inadequate ground return through 5th wheel / king pin. Cable size selection is to be made by the vehicle OEM for specific applications and the specific voltage drop requirements of those applications. This SAE Standard covers two variants of high power two conductor connections: a heavy duty version with horizontally aligned pins, typically for lift-gate battery charging and a medium duty version with vertically aligned pins: typically for loads such as power tarpaulins.
CURRENT
2015-11-24
Standard
J1792/2_201511
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
CURRENT
2015-11-24
Standard
J1792/1_201511
This SAE Standard establishes a test method and a definition for disclosing the suction air volume performance of self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
CURRENT
2015-11-19
Standard
J2224_201511
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
Viewing 1 to 30 of 212

Filter

  • Standard
    212

Subtopics