Criteria

Text:
Content:
Display:

Results

Viewing 211 to 240 of 14525
CURRENT
2016-11-22
Standard
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
2016-11-22
WIP Standard
J2271
This SAE Parts Standard provides dimensional and quality assurance requirements for 1/4 through 2 in sizes of studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series. b. Double end studs (clamping type) where both ends are of the same thread length (UNRC or 8UN). Also called bolt-studs. (These are suitable for mating with nuts or the set end may be installed with anaerobic thread locking compound.) c. Double end studs (interference thread type) with the nut end having UNRC or 8UNR series thread and where the tap end has NC 5 HFS interference fit thread forms. Also called a tap end stud. A complete metric companion to this document is provided in SAE J2271M, therefore no metric equivalents are presented. These studs are primarily or use in ship systems and equipment.
CURRENT
2016-11-21
Standard
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
CURRENT
2016-11-21
Standard
J430_201611
These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.
CURRENT
2016-11-21
Standard
J892M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.
CURRENT
2016-11-18
Standard
ARP6379
This document describes a process for use by ADHP integrators of EEE parts and sub-assemblies (items) that have been targeted for other applications. This document does not describe specific tests to be conducted, sample sizes to be used, nor results to be obtained; instead, it describes a process to define and accomplish application-specific qualification; that provides confidence to both the ADHP integrators, and the integrators’ customers, that the item will performs its function(s) reliably in the ADHP application.
CURRENT
2016-11-18
Standard
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
CURRENT
2016-11-18
Standard
J485_201611
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
CURRENT
2016-11-18
Standard
J483_201611
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
CURRENT
2016-11-18
Standard
J482_201611
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
CURRENT
2016-11-18
Standard
J1053_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
CURRENT
2016-11-18
Standard
J1053M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
CURRENT
2016-11-17
Standard
ARP994B
This document provides recommended practices for the design and selection of tube, hose, and fitting systems that are used to transmit hydraulic fluid on aircraft.
CURRENT
2016-11-16
Standard
AS4664C
SCOPE IS UNAVAILABLE.
CURRENT
2016-11-15
Standard
AMS2590A
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic Almen test strip holder is required for intensity determination.
CURRENT
2016-11-15
Standard
J2656_201611
This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document.
CURRENT
2016-11-15
Standard
J1294_201611
This SAE Recommended Practice covers distributors used on marine engines. NOTE: This includes devices referred to as high voltage switches used for distributing high voltage to the appropriate spark plugs but does not contain any crank position sensing function.
CURRENT
2016-11-15
Standard
J1577_201611
This SAE Recommended Practice provides performance parameters and dimensional specifications for available light sources (replaceable bulbs) which are appropriate for motorcycle headlamps.
CURRENT
2016-11-15
Standard
J2295_201611
This SAE Part Standard covers selected inch screws, bolts, structural bolts, and nuts manufactured in accordance with ASTM International and SAE fastener standards. Appendix A covers bolt blanks to manufacture fitted bolts of specific materials. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document.
2016-11-15
WIP Standard
J902
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or less, as defined by EPA, and M1 category vehicles as defined by the European Commission: a. Minimum performance standards for defrosting and demisting systems. b. Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities.
Viewing 211 to 240 of 14525

Filter

  • Standard
    14525

Subtopics