Criteria

Text:
Content:
Display:

Results

Viewing 181 to 210 of 14525
CURRENT
2016-12-12
Standard
AS44750AR-8
No Scope available.
CURRENT
2016-12-12
Standard
AS27850AR-10
No Scope available.
CURRENT
2016-12-12
Standard
AS63476AR-5
No Scope available.
CURRENT
2016-12-12
Standard
AS63480AR-3
No Scope available.
CURRENT
2016-12-12
Standard
ARP5448/7A
This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a. Destructive Inspection - Cut and measure (not applicable to molded liners) b. Nondestructive Inspection - Radial play (gauge) measurement
CURRENT
2016-12-06
Standard
J1939/11_201612
This document defines a physical layer having a robust immunity to EMI and physical properties suitable for harsh environments. CAN controllers are available which support the CAN Flexible Data Rate Frame Format. These controllers, when used on SAE J1939-11 networks, must be restricted to use only the Classical Frame Format compliant to ISO 11898-1:2015. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
2016-12-06
WIP Standard
AS35051A
No scope available.
2016-12-01
WIP Standard
AS81714/10A
Scope not available.
CURRENT
2016-11-30
Standard
J3096_201611
This SAE Recommended Practice was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications. It addresses Non-Metallic caps and both Metallic and Non-Metallic filler necks.
2016-11-30
WIP Standard
AS5355/2B
During the revision of AS5355/1, /2 and /3 Revision A the "B" dimension was incorrectly located and will be revised.
2016-11-30
WIP Standard
AS5355/3B
During the revision of AS5355/1, /2 and /3 Revision A the "B" dimension was incorrectly located and will be revised.
CURRENT
2016-11-29
Standard
AS5877B
This SAE Aerospace Standard (AS) prescribes requirements for the various types of nozzles that are used for the refueling and defueling of aircraft fitted with pressure fuel servicing systems. It is to be used as a replacement for MIL-N-5877, MS29520 and for all commercial applications.
CURRENT
2016-11-28
Standard
AS21924D
SCOPE IS UNAVAILABLE.
CURRENT
2016-11-28
Standard
J891_201611
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
CURRENT
2016-11-28
Standard
AMS4174E
This specification covers an aluminum alloy in the form of flash welded rings 0.062 to 4.499 inches, incl (1.57 to 114.27 mm incl) in radial thickness, with cross sectional areas up to 32 in2 (206 cm2) (see 8.5).
CURRENT
2016-11-23
Standard
AIR4069C
This SAE Aerospace Information Report (AIR) presents preferred design, assembly, and repair practices for sealing of aircraft integral fuel tanks, including rework of applied fuel tank seals. It addresses engineering designs for integral fuel tanks as they are currently found in practice; and discusses the most practical and conservative methods for producing a reliable, sealed system. Although this AIR presents practices for sealing of integral fuel tanks, the practices presented within this report are practices that are carried throughout sealing that include both pressure and environmental aircraft sealing. Design preferences for optimum sealing are not within the scope of this document. Such discussions can be found in the United States Air Force (USAF) sponsored report, entitled Aircraft Integral Fuel Tank Design Handbook, AFWAL-TR-87-3078.
CURRENT
2016-11-23
Standard
J492_201611
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
CURRENT
2016-11-23
Standard
J892_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.
2016-11-23
WIP Standard
AS407E
To specify minimum requirements for Fuel Flowmeters for use primarily in reciprocating engine powered civil transport aircraft, the operation of which may subject the instruments to the environmental conditions specified in Section 3.3. This Aeronautical Standard covers two basic types of instruments, or combinations thereof, intended for use in indicating fuel consumption of aircraft engines as follows: TYPE I - Measure rate of flow of fuel used. TYPE II - Totalize amount of fuel consumed or remaining.
Viewing 181 to 210 of 14525

Filter

  • Standard
    14525

Subtopics