Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 14525
2017-01-24
WIP Standard
AS3326B
No scope available.
2017-01-24
WIP Standard
AS5620B
This SAE Aerospace Standard (AS) shall be used in conjunction with AMS 4946 to provide requirements for qualification testing and for Qualified Products Listing (QPL) and Qualified Manufacturer Listing (QML) for Ti-3Al-2.5V cold worked and stress relieved hydraulic system tubing. The basic tubing shall comply with the requirements of AMS 4946.
2017-01-24
WIP Standard
AS6171/2A
This document describes the requirements of the following test methods for counterfeit detection of electronic components: Method A: General EVI, Sample Selection, and Handling Method B: Detailed EVI, including Part Weight measurement Method C: Testing for Remarking Method D: Testing for Resurfacing Method E: Part Dimensions measurement Method F: Surface Texture Analysis using SEM The scope of this document is focused on leaded electronic components, microcircuits, multi-chip modules (MCMs), and hybrids. Other EEE components may require evaluations not specified in this procedure. Where applicable this document can be used as a guide. Additional inspections or criteria would need to be developed and documented to thoroughly evaluate these additional part types. If SAE AS6171/2 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
2017-01-19
WIP Standard
AS7469B
This procurement specification covers bolts and screws made from a corrosion and heat resistant, age hardenable, nickel base alloy of the type identified under the Unified Numbering System as UNS N07041 and of 155 ksi tensile strength at room temperature, with maximum test temperature of parts at 1400 °F.
CURRENT
2017-01-19
Standard
AS31021C
SCOPE IS UNAVAILABLE.
CURRENT
2017-01-19
Standard
AS39029D
This specification covers the general requirements for removable crimp, solderless wrap, and solder type electrical contacts for use in connectors and other electric and electronic components (see 6.1) with stranded conductor wire. The contacts shall be capable of operating within the temperature range as specified (see 3.1).
CURRENT
2017-01-18
Standard
AMS3400
This fluid has been used typically to evaluate the ability of elastomeric and other polymeric compounds to conform to designated requirements after immersion in the fluid at a specific temperature and time, as required by an applicable specification, and its use is limited to such applications. This fluid is not intended for operational use in hydraulic systems. Each application should be considered separately.
2017-01-18
WIP Standard
AS5553C
This standard is for use by organizations that procure and/or integrate EEE parts and/or assemblies containing such items. The requirements of this standard are generic and intended to be applied/flowed down, as applicable, through the supply chain to all organizations that procure EEE parts and/or assemblies, regardless of type, size, and product provided. The mitigation of counterfeit EEE parts in this standard is risk-based and these mitigation steps will vary depending on the application, desired performance, and reliability of the equipment/hardware. The requirements of this document are intended to supplement the requirements of a higher level quality standard (e.g., AS/EN/JISQ9100, ISO-9001, ANSI/ASQC E4, ASME NQA-1, AS9120, AS9003, and ISO/TS 16949 or equivalent) and other quality management system documents.
CURRENT
2017-01-12
Standard
AS6305
The standard sets forth the dimensions and gaging system for the Spiral Drive (MORTORQ) System and is supplemental to fastener standards developed that incorporate this drive feature.
2017-01-12
WIP Standard
ARP1231B
This document establishes general gland design criteria for static and dynamic O-ring seal applications used in fluid systems and at fluid pressures common to the aerospace industry. Detailed discussion of design criteria and tables of recommended gland dimensions are contained in the documents listed in Table 1. S.I. unit conversions for U.S. customary units have been provided for reference purposes.
CURRENT
2017-01-12
Standard
AS4841B
This SAE Aerospace Standard (AS) establishes the requirements for 37° flared tube fittings or machined internal cone fluid connection fittings for use with 37° external cone, spherical nose and seal ring fittings in all types of aerospace fluid systems (see Section 6).
2017-01-10
WIP Standard
AS14227D
SCOPE IS UNAVAILABLE.
2017-01-10
WIP Standard
ARP1897A
This document is prepared as an aid in the selection of clamping devices and their use in aerospace equipment for the installation and support of tubing and wiring.
2017-01-09
WIP Standard
AS5117A
No scope available.
CURRENT
2017-01-09
Standard
ARP4378C
This SAE Aerospace Recommended Practice (ARP) provides design and test requirements for high pressure, factory pre-charged, welded bellows hydraulic accumulators.
CURRENT
2017-01-05
Standard
AS21908E
No scope available.
CURRENT
2017-01-05
Standard
AS21907D
SCOPE IS UNAVAILABLE.
CURRENT
2017-01-05
Standard
AS21923C
SCOPE IS UNAVAILABLE.
CURRENT
2017-01-05
Standard
J1636_201701
The purpose of this SAE Recommended Practice is to review factors that influence the behavior of elastomeric components under conditions of loading or deforming at a constant rate and to provide guidance concerning test procedures used to define or specify the load/deformation characteristics of elastomeric components. This characteristic is referred to as Static Stiffness. This is also referred to as a "Static Deflection Test."
CURRENT
2017-01-05
Standard
AS5175A
SCOPE IS UNAVAILABLE.
Viewing 121 to 150 of 14525

Filter

  • Standard
    14525

Subtopics