Criteria

Text:
Content:
Display:

Results

Viewing 31 to 60 of 14812
2017-10-03
WIP Standard
AS6141A
Scope Unavailable.
CURRENT
2017-10-03
Standard
J1965_201710
This SAE Recommended Practice applies to fasteners/fixing nuts as specified in SAE J694 and SAE J1835 used for disc wheels and demountable rim attachment respectively. Only the test methods necessary to ensure proper wheel or rim assembly are specified. Fasteners for less common and special applications are not included.
CURRENT
2017-09-29
Standard
AMS2647F
This specification details requirements and procedures for the detection of defects in aircraft and engine components during maintenance and overhaul operations.
2017-09-28
WIP Standard
J2600
SAE J2600 applies to the design and testing of Compressed Hydrogen Surface Vehicle (CHSV) fueling connectors, nozzles, and receptacles. Connectors, nozzles, and receptacles must meet all SAE J2600 requirements and pass all SAE J2600 testing to be considered as SAE J2600 compliant. This document applies to devices which have Pressure Classes of H11, H25, H35, H50 or H70. 1.1 Purpose SAE J2600 is intended to: • Prevent vehicles from being fueled with a Pressure Class greater than the vehicle Pressure Class; • Allow vehicles to be fueled with Pressure Class equal to or less than the vehicle Pressure Class, • Prevent vehicles from being fueled by other compressed gases dispensing stations; • Prevent other gaseous fueled vehicles from being fueled by hydrogen dispensing stations.
CURRENT
2017-09-27
Standard
ARP4763
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to define the requirements for aerospace hydraulic relief valves, including details pertinent to the design, performance, fabrication, and testing of the relief valves.
CURRENT
2017-09-27
Standard
AS5179C
Propose revision to add conductive high purity aluminum coating per MIL-DTL-83488 for aluminum alloy fittings. The W code aluminum parts with new finish will be distinguished by new finish code V at the end of part number.
2017-09-26
WIP Standard
AMS2634C
This specification covers procedures for ultrasonic inspection of thin wall metal tubing of titanium, titanium alloy, and corrosion and heat resistant steels and alloys having nominal OD over 0.1875 inch (4.762 mm) with OD to wall thickness ratio of 8 or greater and wall thickness variation not exceeding + or - 10% of nominal.

This process has been used typically for locating internal defects, such as cracks, voids, seams, and other discontinuities, which may or may not be exposed to the surface, but usage is not limited to such applications.

2017-09-26
WIP Standard
ARP4402A
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current inspection of open fastener holes in aluminum aircraft structures.
2017-09-26
WIP Standard
AS5371A
This SAE Aerospace Standard (AS) establishes requirements for the manufacture of ship-type reference standards containing artificial flaws (notches) for use in the magnetic particle inspection process.
2017-09-26
WIP Standard
AMS2644G
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
CURRENT
2017-09-25
Standard
AS100026B
No scope available
2017-09-25
WIP Standard
AS5969F
SCOPE IS UNAVAILABLE.
2017-09-24
WIP Standard
ARP5584A
This SAE Aerospace Recommended Practices (ARP) covers the definitions, functions and broad application guidelines of modern aerospace vehicle electric power management systems. As aerospace control systems have become more sophisticated and autonomous, the electric power subsystem no longer is just a generation and distribution bus control system. New electric power systems include integration of individual load logic control, protection, generation, distribution, and load management. This system can report to a higher level control system, typically a vehicle management system, or can be an autonomous system within itself reporting and responding to operator commands.
2017-09-23
WIP Standard
AMS6352L
This specification covers an aircraft quality, low alloy steel in the form of sheet, strip, and plate. These products have been used typically for heat treated parts and structures that may require welding during fabrication, but usage is not limited to such applications. It may be through-hardened to a minimum tensile strength of 180 ksi (1241 MPa) in sections 0.125 inch (3.18 mm) and under in nominal thickness and proportionately lower strength in heavier section thicknesses.
CURRENT
2017-09-22
Standard
AS150F
This SAE Aerospace Standard (AS) establishes Type classification for those hose assemblies commonly used in aerospace fuel, lubricating oil, and hydraulic fluid systems.
2017-09-22
WIP Standard
AS39901C
This standard covers the requirements for non-separable, airframe anti-friction needle bearings, corrosion resistant and traditional materials, intended for use in flight vehicle control systems, with radial loads. Under Department of Defense (DoD) Policies and Procedures, any qualification requirements and associated Qualified Products Lists (QPLs) are mandatory for DoD contracts. Any material relating to QPLs have not been adopted by SAE and are not part of this SAE technical document.
2017-09-20
WIP Standard
AS5148A
This SAE Aerospace Standard (AS) describes the assembly, installation and torque values for flareless and straight thread fluid fittings and tube assemblies.
CURRENT
2017-09-20
Standard
AMS2550F
This specification covers the enginering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
CURRENT
2017-09-20
Standard
ARP1575C
This document describes a hand-applied, nontank, phosphoric acid anodizing process for surface preparation of aluminum alloys required to achieve optimum bondline durability for structural adhesive bonding.
2017-09-19
WIP Standard
AS21231B
No scope available.
2017-09-19
WIP Standard
AS21232B
No scope available.
2017-09-19
WIP Standard
AS21233B
No scope available.
CURRENT
2017-09-19
Standard
J2606_201709
Drain and Fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 – 8 vehicles.
Viewing 31 to 60 of 14812

Filter

  • Standard
    14812

Subtopics