Criteria

Text:
Display:

Results

Viewing 61 to 90 of 6758
2017-03-28
Technical Paper
2017-01-1350
Jon Olson, Mark Fleming, Ram Krishnaswami, Robert Pellillo
Abstract The fuel filler tube check valve (FTCV) is an integral part of a vehicle’s refueling system. The primary function of this valve is to control the refueling characteristics in a manner that enables the vehicle to be refueled efficiently and under wide ranging conditions, while limiting the amount of fuel or fuel vapor emissions being released into the environment. These valves accomplish this function by allowing the flow of gasoline to pass through the valve and into the tank during the refueling process with minimal restriction while limiting the reverse flow as the fuel tank approaches full. The location of these valves varies from vehicle to vehicle but are generally located within the fuel filler or fuel tank system. They have been engineered and developed to ensure the vehicle will meet customer and industry refueling requirements as well as refueling emissions mandates from the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB).
2017-03-28
Technical Paper
2017-01-0893
Marek Tatur, Kiran Govindswamy, Dean Tomazic
Abstract Demanding CO2 and fuel economy regulations are continuing to pressure the automotive industry into considering innovative powertrain and vehicle-level solutions. Powertrain engineers continue to minimize engine internal friction and transmission parasitic losses with the aim of reducing overall vehicle fuel consumption. Strip friction methods are used to determine and isolate components in engines and transmissions with the highest contribution to friction losses. However, there is relatively little focus on friction optimization of Front-End-Accessory-Drive (FEAD) components such as alternators and Air Conditioning (AC) compressors. This paper expands on the work performed by other researchers’ specifically targeting in-depth understanding of system design and operating strategy.
2017-03-28
Technical Paper
2017-01-1122
Yashodhan V. Joshi
Abstract Vehicle noise has reduced over the years due to the customer demand for quieter vehicles. As the background noises such as combustion noise, pumping noise, etc. have reduced, mechanical noises such as gear noise have become prominent and a major cause of customer complaints. Engine timing gear train uses gears for transferring torque to cam and accessory gears. As engines have become quieter by efforts to reduce the combustion noise, as well as, by moving away from mechanical fuel pumps to common rail fuel pumps, the gear train noise has come under increased scrutiny. Gear whine could be a result of multiple factors. Gear profile distortion is one of the factors. Gear torque variation also has a significant effect on gear whine. Operation of the accessory drives such as hydraulic pumps under variable loads and speeds, is one of the major challenges for resolving a gear whine issue in the engine gear train.
2017-03-28
Technical Paper
2017-01-1709
Zhigang Wei, Sarat Das, Ryan Barr, Greg Rohrs, Robert Rebandt, Xiao Wu, HongTae Kang
Abstract Recent stringent government regulations on emission control and fuel economy drive the vehicles and their associated components and systems to the direction of lighter weight. However, the achieved lightweight must not be obtained by sacrificing other important performance requirements such as manufacturability, strength, durability, reliability, safety, noise, vibration and harshness (NVH). Additionally, cost is always a dominating factor in the lightweight design of automotive products. Therefore, a successful lightweight design can only be accomplished by better understanding the performance requirements, the potentials and limitations of the designed products, and by balancing many conflicting design parameters. The combined knowledge-based design optimization procedures and, inevitably, some trial-and-error design iterations are the practical approaches that should be adopted in the lightweight design for the automotive applications.
2017-03-28
Technical Paper
2017-01-0244
Joshua Lyon, Junheung Park, Yakov Fradkin, Jeff Tornabene
Abstract We describe an optimization model developed by Ford Motor Company to reallocate stamped parts between facilities when business conditions change. How can the business meet new targets when demand starts to exceed existing capacity? Likewise, how can it respond when demand is lower than expected? Sometimes the business can reduce costs by transferring production to a different location or by outsourcing parts. We describe in this paper how mathematical optimization can identify solutions that balance both logistical and outsourcing costs. We explain the algorithm and demonstrate with a small example how it recommends sourcing plans that minimize cost.
2017-03-28
Technical Paper
2017-01-1147
Hyunjun Kim, Jingeon Kang, Dongsuk Kum
Abstract Input- and output-split hybrids using a single planetary gear (PG) can provide high fuel economy, but they tend to suffer from low acceleration performance. In order to improve their acceleration performance, speed reduction (multiplication) gears (SRG/SMG) have often been employed in various mass-produced split hybrids. In fact, adding one SRG (SMG) to input- or output-split hybrids can improve not only the acceleration performance, but also the fuel economy. Nevertheless, the full potentials of using SRGs (SMGs) have not yet been thoroughly investigated because the design space of input- and output-split configurations using one SRG (SMG) is huge; 432 configurations can be generated using two PGs where one PG is used as an SRG/SMG. Thus, in order to investigate the impacts of SRG (SMG) within a reasonable time, an efficient analysis procedure is required.
2017-03-28
Technical Paper
2017-01-1025
Qinghe Luo, Baigang Sun, Xi Wang
Hydrogen is a promising energy carrier because it is characterized by a fast combustion velocity, a wide range of sources, and clean combustion products. A hydrogen internal combustion engine (H2ICE) with a turbocharger has been used to solve the contradiction of power density and control NOx. However, the selection of a H2ICE compressor with a turbocharger is very different from traditional engines because of gas fuel. Hydrogen as a gas fuel has the same volume as its cylinder and thus increases pressure and reduces the mass flow rate of air in cylinder for a port fuel injection-H2ICE (PFI-H2ICE). In this study, a general method involving a H2ICE with a turbocharger is proposed by considering the effect of hydrogen on cylinders. Using this method, we can calculate the turbocharged pressure ratio and mass flow rate of air based on the target power and general parameters. This method also provides a series of intake temperatures of air before calculation to improve accuracy.
2017-03-28
Technical Paper
2017-01-1240
Koki Matsushita
Abstract For the purpose of improving vehicle fuel efficiency, it is necessary to reduce energy loss in the alternator. We have lowered the resistance of the rectifying device and connecting components, and control the rectifying device with an IC to reduce rectification loss. For the package design, we have changed the structure of the part on which the rectifying device is mounted into a high heat dissipation type. The new structure has enabled optimizing the size of the rectifying device, resulting in the reduction of size of the package. In addition, the rectifying device is mounted using a new soldering material and a new process, which has improved the reliability of the connection. Moreover, since the alternator has introduced a new system, the controller IC has a function for preventing malfunction of the rectifying device and a function for detecting abnormalities, in order to ensure safety.
2017-03-28
Technical Paper
2017-01-1229
Ken Yamamoto, Nobuyasu Sadakata, Hidetoshi Okada, Yusuke Fujita
Abstract Electric oil pumps (EOP) for automobiles are used to lubricate and cool moving parts and supply oil pressure to components. Conventional EOPs consist of two separate units including a motor driver and a pump system comprised of a motor and a pump, which impedes layout flexibility for vehicles. To overcome this shortcoming, we have developed an ECU (electronic control unit)-integrated oil pump in which a driver, a motor and a pump are incorporated as a single unit. In the course of the project, we focused on improving vibration resistance and developing a compact design. The first challenge was to improve vibration resistance because of the driver located in close proximity to the powertrain. Since the driver is installed on the motor unit via electrically welded bus bars, the joints of the driver and the bus bar become susceptible to vibration.
2017-03-28
Technical Paper
2017-01-1333
Sasikumar P, C. Sujatha, Chinnaraj K.
Abstract In commercial vehicles, exhaust system is normally mounted on frame side members (FSM) using hanger brackets. These exhaust system hanger brackets are tested either as part of full vehicle durability testing or as a subsystem in a rig testing. During initial phases of product development cycle, the hanger brackets are validated for their durability in rig level testing using time domain signals acquired from mule vehicle. These signals are then used in uni-axial, bi-axial or tri-axial rig facilities based on their severity and the availability of test rigs. This paper depicts the simulation method employed to replicate the bi-directional rig testing through modal transient analysis. Finite Element Method (FEM) is applied for numerical analysis of exhaust system assembly using MSC/Nastran software with the inclusion of rubber isolator modeling, meshing guidelines etc. Finite Element Analysis (FEA) results are in good agreement with rig level test results.
2017-03-28
Technical Paper
2017-01-1062
Abdelkrim Zouani, Gabriela Dziubinschi, Vidya Marri, Simon Antonov
Abstract In modern automotive engines, Variable Displacement Oil Pump (VDOP) is becoming the pump of choice to enable reduction in friction and delivery of stringent fuel economy. However, this pump creates pressure ripples, at the outlet port during oil pump shaft rotation, causing oscillating forces within the system and leading to the generation of tonal noises and vibrations. In order to minimize the level of noise, different porting geometries and vane spacing are used. This paper describes an optimization method intended to identify the best possible spacing of the vanes in the conventional 7-vanes, 9-vanes and 11-vanes oil pumps. The method integrates a Matlab routine with the modeFRONTIER software to create the required design space in order to perform a multi-objective optimization using a genetic algorithm. Results of this optimization method are discussed and a design guideline for the VDOP vane spacing is disclosed.
2017-03-28
Technical Paper
2017-01-1331
Marko Basic, Thomas Resch
Abstract This paper describes a numerical study of the effect of hollow crankshafts on crankshaft local strength and durability as well as slider bearing contact behavior. Crankshaft dynamic simulation for durability is still a challenging task, although numerical methods are already worldwide established and integrated part of nearly every standard engine development process. Such standard methods are based on flexible multi-body dynamic simulation, combined with Finite Element analysis and multi-axial fatigue evaluation. They use different levels of simplification and consider the most influencing phenomena relevant for durability. Lightweight design and downsizing require more and more detailed methods due to higher deformation of the crankshaft. This is especially true for hollow shafts, as present in motorsport design or aerospace applications, but also for standard engine having high potential for significant weight savings.
2017-03-28
Technical Paper
2017-01-0543
Oliver Hofmann, Shijin Han, Daniel Rixen
Abstract This study discusses model-based injection rate estimation in common rail diesel injectors exhibiting aging phenomena. Since they result in unexpected injection behavior, aging effects like coking or cavitation may impair combustion performance, which justifies the need for new modeling and estimation approaches. To predict injection characteristics, a simulation model for the bottom section of the injector is introduced, with a main focus on modeling the hydraulic components. Using rail pressure and control piston lift as inputs, a reduced model is then derived in state-space representation, which may be used for the application of an observer in hardware-in-the-loop (HIL) environments. Both models are compared and validated with experimental data, with which they show good agreement. Aging effects and nozzle wear, which result in model uncertainties, are considered using a fault model in combination with an extended Kalman filter (EKF) observer scheme.
2017-03-28
Technical Paper
2017-01-1034
Ben Zhao, Liangjun Hu, Abraham Engeda, Harold Sun
Abstract As the variable nozzle turbine(VNT) becomes an important element in engine fuel economy and engine performance, improvement of turbine efficiency over wide operation range is the main focus of research efforts for both academia and industry in the past decades. It is well known that in a VNT, the nozzle endwall clearance has a big impact on the turbine efficiency, especially at small nozzle open positions. However, the clearance at hub and shroud wall sides may contribute differently to the turbine efficiency penalty. When the total height of nozzle clearance is fixed, varying distribution of nozzle endwall clearance at the hub and shroud sides may possibly generate different patterns of clearance leakage flow at nozzle exit that has different interaction with and impact on the main flow when it enters the inducer.
2017-03-28
Technical Paper
2017-01-0684
Vickey B. Kalaskar, Raphael Gukelberger, Bradley Denton, Thomas Briggs
Abstract Dedicated EGR has shown promise for achieving high efficiency with low emissions [1]. For the present study, a 4-cylinder turbocharged GDI engine which was modified to a D-EGR configuration was used to investigate the impact of valve phasing and different injection strategies on the reformate production in the dedicated cylinder. Various levels of positive valve overlap were used in conjunction with different approaches for dedicated cylinder over fueling using PFI and DI fuel systems. Three speed-load combinations were studied, 2000 rpm 4 bar IMEPg, 2000 rpm 12 bar IMEPg, and 4000 rpm 12 bar IMEPg. The primary investigation was conducted to map out the dedicated cylinders' performance at the operating limits of intake and exhaust cam phasing. In this case, the limits were defined as conditions that yielded either no reformate benefit or led to instability in the dedicated cylinder.
2017-03-28
Journal Article
2017-01-1472
Niels Pasligh, Robert Schilling, Marian Bulla
Abstract Rivets, especially self-piercing rivets (SPR), are a primary joining technology used in aluminum bodied vehicles. SPR are mechanical joining elements used to connect sheets to create a body in white (BiW) structure. To ensure the structural performance of a vehicle in crash load cases it is necessary to describe physical occurring failure modes under overloading conditions in simulations. One failure mode which needs to be predicted precisely by a crash simulation is joint separation. Within crash simulations a detailed analysis of a SPR joint would require a very high computational effort. The conflict between a detailed SPR joint and a macroscopic vehicle model needs to be solved by developing an approach that can handle an accurate macroscopic prediction of SPR behavior with a defined strength level with less computational effort. One approach is using a cohesive material model for a SPR connection.
2017-03-28
Journal Article
2017-01-1124
Enrico Galvagno, Pablo Gutierrez, Mauro Velardocchia, Alessandro Vigliani
Abstract This paper investigates the effect of the powertrain mounting system on the linear and nonlinear torsional dynamical behaviour of a transmission system. To this aim, two dynamic models, one with rigid mounts and the other with flexible mounts, are presented and compared: the first model considers only the torsional dynamics of transmission and driveline, while the second model includes also a 3 degrees-of-freedom powertrain block. The mechanical coupling and interaction between the powertrain block and transmission system is discussed and formulated. These models are then analyzed in terms of vibrational mode shapes, natural frequencies and Frequency Response Functions (FRFs); a sensitivity analysis of the main transmission parameters, e.g. the gear ratio, is also presented.
2017-03-28
Journal Article
2017-01-0165
Jingwei Zhu, Stefan Elbel
Abstract Expansion work recovery by two-phase ejector is known to be beneficial to vapor compression cycle performance. However, one of the biggest challenges with ejector vapor compression cycle is that the ejector cycle performance is sensitive to working condition changes which are common in many applications, including automotive AC systems. Different working conditions require different ejector geometries to achieve maximum performance. Slightly different geometries may result in substantially different COPs under the same conditions. Ejector motive nozzle throat diameter (motive nozzle restrictiveness) is one of the key parameters that can significantly affect COP. This paper presents the experimental investigation of a new motive nozzle restrictiveness control mechanism for two-phase ejectors used in vapor compression cycles, which has the advantages of being simple, potentially less costly and less vulnerable to clogging.
2017-03-28
Journal Article
2017-01-0484
Harchetan Singh Aneja, Harmeet Singh, Aashish Parmar, Rohan Sharma
Abstract The automotive industry, known for its competitiveness & innovations globally, researches for continuous improvement of part performances along with reduction of cost & weight. These are amongst the top priority goals across all OEMs. In the long list of automobile parts, pipe clamps have paved their way of design through generations from being of metal to plastic that has expanded its scope of application & performance. In an automobile, plastic clamps are widely used to hold single or multiple water, fuel or brake pipes of various diameters to vehicle body at various locations such as underbody (prone to stone chipping) or engine room (prone to high temperatures), etc. Plastic clamps are preferred over metallic clamps for their cost, weight, performance & productivity. Primarily, in all application areas, a clamp must be able to hold the pipes with consistent & sufficient performance that is quantified through parameters such as thrust force and pipe removal force.
2017-03-28
Journal Article
2017-01-1313
Bao Wang, Jianhua Zhou, Min Xu
Abstract Manufacturing tolerances are inevitable in nature. For the bearings used in internal combustion engines, the manufacturing tolerances of roundness, which is of the micron scale, can be very close to the bearing radial clearance, and as a result the roundness could affect the lubrication of the bearings and thus affecting the friction loss of the engine. However, there is insufficient understanding of this mechanism. This study aims to find out the effects of the amplitude and the phase of journal roundness in the shape of ellipse on the lubrication of engine bearings. The elastohydrodynamic (EHD) theory is applied to model the bearing since the EHD model takes account of the elastic deformation of the journal and the bearing shell. The analysis of the DOE results shows the existence of roundness can be beneficial to the lubrication in some cases.
2017-03-28
Technical Paper
2017-01-0693
Seungwoo Kang, Wonkyu Cho, Choongsik Bae, Youngho Kim
Abstract This paper investigated the influence of the injector nozzle geometry on fuel consumption and exhaust emission characteristics of a light-duty diesel engine with 250 MPa injection. The engine used for the experiment was the 0.4L single-cylinder compression ignition engine. The diesel fuel injection equipment was operated under 250MPa injection pressure. Three injectors with nozzle hole number of 8 to 10 were compared. As the nozzle number of the injector increased, the orifice diameter decreased 105 μm to 95 μm. The ignition delay was shorter with larger nozzle number and smaller orifice diameter. Without EGR, the particulate matter(PM) emission was lower with larger nozzle hole number. This result shows that the atomization of the fuel was improved with the smaller orifice diameter and the fuel spray area was kept same with larger nozzle number. However, the NOx-PM trade-offs of three injectors were similar at higher EGR rate and higher injection pressure.
2017-03-28
Technical Paper
2017-01-0860
PengBo Dong, Jun Yamauchi, Keiya Nishida, Youichi Ogata
Abstract With the aim of improving engine performance, recent trend of fuel injection nozzle design followed by engineers and researchers is focusing on more efficient fuel break up, atomization, and fuel evaporation. Therefore, it is crucial to characterize the effect of nozzle geometric design on fuel internal flow dynamics and the consequent fuel-air mixture properties. In this study, the internal flow and spray characteristics generated by the practical multi-hole (10 holes) nozzles with different nozzle hole length and hole diameter were investigated in conjunction with a series of computational and experimental methods. Specifically, the Computational Fluid Dynamics (CFD) commercial code was used to predict the internal flow variation inside different nozzle configurations, and the high-speed video observation method was applied to visualize the spray evolution processes under non-evaporating conditions.
2017-03-28
Technical Paper
2017-01-0840
Carlo Beatrice, Marianna Migliaccio, Alessandro Montanaro, Valentina Fraioli, Pierpaolo Napolitano, Luigi Allocca
Abstract In the aim of reducing CO2 emissions and fuel consumption, the improvement of the diesel engine performance is based on the optimization of the whole combustion system efficiency. The focus of new technological solutions is devoted to the optimization of thermodynamic efficiency especially in terms of reduction of losses of heat exchange. In this context, it is required a continuous development of the engine combustion system, first of all the injection system and in particular the nozzle design. To this reason in the present paper a new concept of an open nozzle spray was investigated as a possible solution for application on diesel engines. The study concerns some experimental and numerical activities on a prototype of an open nozzle. An external supplier provided the prototypal version of the injector, with a dedicated piezoelectric actuation system, and with an appropriate choice of geometrical design parameters.
2017-03-28
Technical Paper
2017-01-0822
Jim Elkjær Bebe, Kasper Steen Andersen
Abstract The purpose of this work is to determine essential spray parameters for a specific nozzle to be integrated in computational fluid dynamics (CFD) simulations of selective catalytic reduction systems (SCR) based on the injection of urea water solution (UWS). As Dinex does not develop nozzles, but rather integrate nozzles from a variety of manufacturers, the spray data made available is of an inhomogeneous quality. This paper presents the results of a simple, partial validation and calibration of a CFD simulation performed with the commercial CFD code AVL FIRE 2014.2 using the Lagrangian discrete droplet method. The validation is based on a novel and low cost experimental setup, where the experimental method utilizes high-speed imaging to provide spray cone angle, axial spray penetration length and spray plume droplet density.
2017-03-28
Journal Article
2017-01-1316
Dhaval Vaishnav, Mohsen Ehteshami, Vylace Collins, Syed Ali, Alan Gregory, Matthew Werner
Abstract A jet pump (also known as ejector) uses momentum of a high velocity jet (primary flow) as a driving mechanism. The jet is created by a nozzle that converts the pressure head of the primary flow to velocity head. The high velocity primary flow exiting the nozzle creates low pressure zone that entrains fluid from a secondary inlet and transfers the total flow to desired location. For a given pressure of primary inlet flow, it is desired to entrain maximum flow from secondary inlet. Jet pumps have been used in automobiles for a variety of applications such as: filling the Fuel Delivery Module (FDM) with liquid fuel from the fuel tank, transferring liquid fuel between two halves of the saddle type fuel tank and entraining fresh coolant in the cooling circuit. Recently, jet pumps have been introduced in evaporative emission control system for turbocharged engines to remove gaseous hydrocarbons stored in carbon canister and supply it to engine intake manifold (canister purging).
2017-03-28
Technical Paper
2017-01-1080
Yanan Wei, Shuai Yang, Xiuyong Shi, Jiaqi Li, Xuewen Lu
Abstract This paper aimed at a gasoline engine "cylinder head- cylinder gasket-cylinder body-bolt" sealing system, built the 3D solid model and the finite element model of the assembly, and calculated the stress and strain of the cylinder gasket under the cylinder pressure and the deformation of the engine block. In addition, based on the calculation results, this paper put forward the optimization scheme of the cylinder gasket structure, re-established the simulation model, and get the calculation results. The calculation results showed that the cylinder pressure had influence on the sealing performance of the cylinder gasket, and the influence of cylinder pressure should be taken into consideration when designing the cylinder gasket. When the cylinder pressure was applied, the overall contact stress of the cylinder gasket had decreased, and the whole remaining height of the gasket had increased.
2017-03-28
Technical Paper
2017-01-1075
Wen Chen, Reda Adimi, Xingfu Chen, Todd Brewer, Ling Shi
Abstract In CAE analysis of cylinder bore distortion, valve seat distortion, valve guide-to-seat misalignment and cam bore misalignment, nodal displacements on the cylinder bore inner surface and on the gage lines of valve seats, valve guides and cam bores are typically output. Best fit cylinders, best fit circles and best fit lines are computed by utilizing the output displacements of the deformed configuration. Based on the information of the best fit geometry, distortions and misalignments are assessed. Some commercial and in-house software is available to compute the best fit cylinders, best fit circles and best fit lines. However, they suffer from the drawback that only one best-fit geometry can be computed at a time. Using this kind of software to assess distortions and misalignments of engine components would be tedious and prone to error, since data transfer as well as the intermediate computation has to be done by hand, and the process is not automatic.
2017-03-28
Technical Paper
2017-01-1066
Christoph Beerens, Alexander Mueller, Kimm Karrip
Abstract As emissions regulations and carbon footprint are more and more demandingly controlled, thermal efficiency of engine components must be optimized. Valve group components have to allow for ever increasing temperatures, endure aggressive condensates or even contribute directly to rising efficiency and emissions demands. Even with integrated and cooled exhaust manifolds, the exhaust valves are meeting full combustion temperatures, especially for stoichiometric combustion. MAHLE has developed a new technology in order to measure valve temperatures in real time, i.e. Transient Valve Temperature Measurement (TVTM). This is a complex methodology using thermocouples installed inside of the valves, offering the possibility to run the engine at different conditions, without any functional changes in the valve train system at all. Specifically valve rotation is not affected and thus temperatures all around the valve seat can be captured during rotation.
2017-03-28
Technical Paper
2017-01-1090
Praveen Kumar Tumu, KungHao Wang, Juhchin Yang, Selvakumar Palani, Balaji Srinivasan
Abstract In the shop floor, cracking issue was noticed during assembly of valve seat and valve guide in the engine cylinder head, especially near the valve seating area. This paper reveals a non- linear finite element methodology to verify the structural integrity of a cylinder head during valve seat and valve guide assembly press-in operation under the maximum material condition, i.e., smallest hole size on cylinder head for valve seat and guide and largest diameter of valve seat and guide. Material and geometrical nonlinearities, and contact are included in this method to replicate the actual seat and guide press-in operation which is being carried out in shop floor. The press-in force required for each valve seat and valve guide assembly is extracted from simulation results to find out the tonnage capacity of pressing machine for cylinder head assembly line. Stress and plastic deformation due to assembly load are the criteria checked against the respective material yield.
2017-03-28
Technical Paper
2017-01-1091
Todd Brewer, Xingfu Chen
Abstract Typically, modern automotive engine designs include separate cylinder heads and cylinder blocks and utilize a multilayer steel head gasket to seal the resulting joint. Cylinder head bolts are used to hold the joint together and the non-linear properties of head gasket provide capability to seal the movement within the joint, which is essential for engine durability and performance. There are three major failure modes for head gasket joint: fluid or gas leakage due to low sealing pressure, head gasket bead cracking due to high gap alternation and scrubbing/fretting due to pressure and temperature fluctuations causing lateral movement in the joint. During engine operation, the head gasket design should be robust enough to prevent all three failure modes and the resulting design must consider all three major failure modes to provide acceptable performance.
Viewing 61 to 90 of 6758

Filter

Subtopics