Criteria

Text:
Display:

Results

Viewing 1 to 30 of 1567
2017-12-06
Technical Paper
2017-01-5100
Thorsten Langhorst, Olaf Toedter, Thomas Koch, Patrick Gonner, Matthew Borst, Richard Morton
Abstract Particulates and nitrogen oxides comprise the main emission components of the Diesel combustion and therefore are subject to exhaust emission legislation in respective applications. Yet, with ever more stringent emission standards and test-procedures, such as in passenger vehicle applications, resulting exhaust gas after-treatment systems are quite complex and costly. Hence, new technologies for emission control have to be explored. The application of non-thermal plasma (NTP) as a means to perform exhaust gas after-treatment is one such promising technology. In several publications dealing with NTP exhaust gas after-treatment the plasma state was generated via dielectric barrier discharges. Another way to generate a NTP is by a corona high-frequency discharge. Hence, in contrast to earlier publications, the experiments in this publication were conducted on an operated series-production Diesel engine with an industrial pilottype corona ignition system.
2017-11-05
Technical Paper
2017-32-0095
Preechar Karin, Warawut Amornprapa, Phiranat Khamsrisuk, Pol-ake Budsayahem, Pattara Chammana, Kobsak Sriprapha, Katsunori Hanamura
The soot contamination in used engine oils of diesel engine vehicles was about 1% by weight. The soot and metal wear particle sizes might be in the range of 0-1 µm and 1-25 µm, respectively. The characteristics of soot affecting on metal wear was investigated. Soot particle contamination in diesel engine oil was simulated using carbon black. Micro-nanostructure of soot particles were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and laser diffraction spectroscopy (LDS). The metal wear behavior was studied by means of a Four-Ball tribology test with wear measured. Wear roughness in micro-scale was investigated by high resolution optical microscopy (OM) , 3D rendering optical technique and SEM image processing method. It was found that the ball wear scar diameter increased proportionally to the soot primary particle size. The effect of biodiesel contamination were also increasing in wear scar diameter.
2017-11-05
Technical Paper
2017-32-0094
Preechar Karin, Park Watanawongskorn, Jiramed Boonsakda Eakkawut Saenkhumvong, Sippakorn Rungsritanapaisan, Settavit Srivarocha, Chinda Charoenphonphanich, Nuwong Chollacoop, Katsunori Hanamura
Diesel engines are high thermal efficiency because of high compression ratio but produce high concentration of particulate matter (PM) because of direct injection fuel diffusion combustion. PM must be removed from the exhaust gas to protect human health. This research describes biodiesel engine performance, efficiency and combustion behavior using combustion pressure analyzer. It was clearly observed that PM emitted from CI engines can be reduced by using renewable bio-oxygenated fuels. The morphology and nanostructure of fossil fuel and biofuel PMs were investigated by using a Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The morphology of biodiesel and diesel doesn’t have much different in the viewpoint of particulate matter trapping using DPF micro surface pores. The agglomerated ultrafine particles and primary nanoparticles sizes of diesel and biodiesel engine’s PM are approximately 50-500 nm and 20-50 nm, respectively.
2017-11-05
Technical Paper
2017-32-0126
Huynh Thanh Cong, Takahiro Kashima, Daisuke Komasaki, Yuta Saito, Akihiko Azetsu
To explore the production and oxidation characteristics of soot in the flame of diesel jet under the condition equivalent to the direct injection diesel engine condition, the effect of three different important parameters (including injection pressure, injection duration, and oxygen concentration) are experimentally examined. For these purposes, a small CVCC (constant volume combustion chamber) with the volume of 60cc equivalent to the volume of combustion chamber of automotive diesel engine is used. To obtain the experimental data of soot production and oxidation, in experiments, the ambient condition of temperature, pressure and oxygen concentration before injection timing are prepared by the combustion of lean hydrogen mixture (with help of 8 spark plugs) at a high temperature and pressure condition around 1000K and 4.5MPa. The common rail type injector with 8 injection holes for modern diesel engine is attached to this vessel.
2017-10-13
Technical Paper
2017-01-5017
Ronith Stanly, Gopakumar Parameswaran, R Rajkiran
Abstract Conventionally, influence of injector coking deposits has been studied using accelerated coking methods. For this work we used in-use vehicles fitted with Common Rail Direct injection (CRDi) injectors in “as-is where is” condition with considerable coked injector deposits. They were then cleaned with a commercial fuel system cleaning solution which did not require the removal of injectors; the influence of injector deposits on vehicular performance and spray field were studied. It was observed that the removal of coking deposits resulted in an increase in the peak power of the vehicle, a lower fuel injected quantity and lower fuel injection duration. It was also observed that the fuel system cleaning procedure resulted in better atomization of fuel spray, better uniformity of the multiple spray jets and an increase in the flow rate of the test injectors.
2017-10-08
Technical Paper
2017-01-2287
Aniseh Abdalla, Guoyang Wang, Jun Zhang, Shi-Jin Shuai
Abstract Advanced exhaust after-treatment technology is required for heavy-duty diesel vehicles to achieve stringent Euro VI emission standards. Diesel particulate filter (DPF) is the most efficient system that is used to trap the particulate matter (PM), and particulate number (PN) emissions form diesel engines. The after-treatment system used in this study is catalyzed DPF (CDPF) downstream of diesel oxidation catalyst (DOC) with secondary fuel injection. Additional fuel is injected upstream of DOC to enhance exothermal heat which is needed to raise the CDPF temperature during the active regeneration process. The objective of this research is to numerically investigate soot loading and active regeneration of a CDPF on a heavy-duty diesel engine. In order to improve the active regeneration performance of CDPF, several factors are investigated in the study such as the effect of catalytic in filter wall, soot distribution form along filter wall, and soot loads.
2017-10-08
Journal Article
2017-01-2291
Sandro Gail, Takashi Nomura, Hitoshi Hayashi, Yuichiro Miura, Katsumi Yoshida, Vinod Natarajan
Abstract In emerging markets, Port Fuel Injection (PFI) technology retains a higher market share than Gasoline Direct Injection (GDI) technology. In these markets fuel quality remains a concern even despite an overall improvement in quality. Typical PFI engines are sensitive to fuel quality regardless of brand, engine architecture, or cylinder configuration. One of the well-known impacts of fuel quality on PFI engines is the formation of Intake Valve Deposits (IVD). These deposits steadily accumulate over time and can lead to a deterioration of engine performance. IVD formation mechanisms have been characterized in previous studies. However, no test is available on a state-of-the-art engine to study the impact of fuel components on IVD formation. Therefore, a proprietary engine test was developed to test several chemistries. Sixteen fuel blends were tested. The deposit formation mechanism has been studied and analysed.
2017-10-08
Technical Paper
2017-01-2269
Shijun Dong, Xiaobei Cheng, Biao Ou, Can Yang, Zhaowen Wang, Fumin Pan
Abstract Based on a composed PRF/ethanol/PAH mechanism, simulations were conducted to investigate the combustion characteristics of n-heptane spray under premixed ethanol/air and iso-octane/air atmosphere in a combustion vessel. The effects of premixed ethanol and iso-octane on ignition delay, important soot precursors and soot volume fraction of n-heptane spray were studied. Also, simulated results with and without considering the cooling effects of premixed fuel vaporization were compared. When the cooling effect of premixed fuel vaporization was not considered, simulations showed that premixed ethanol could increase the ignition delay of n-heptane spray at ambient temperatures below 850K. However, premixed iso-octane showed little inhibition effect on ignition of n-heptane spray. Also, it was found that both premixed ethanol and iso-octane contributed to faster ignition under high ambient temperatures.
2017-10-08
Technical Paper
2017-01-2247
Wenbin Zhang, Haichun ding, Shijin Shuai, Bin Zheng, Alex Cantlay, Vinod Natarajan, Zhang Song ZHAN, Yunping Pu
Abstract Gasoline direct injection (GDI) engines have been developed rapidly in recent years, driven by stringent legislative requirements on vehicle fuel efficiency and emissions. However, one challenge facing GDI is the formation of particulate emissions, particularly with the presence of injector tip deposits. The Chinese market features some gasoline fuels that contain no detergent additives and are prone to deposit formation, which can affect engine performance and emissions. The use of detergent additives to mitigate the formation of injector deposits in a GDI engine was investigated in this study by testing a 1.5L turbocharged GDI engine available in the Chinese market. The engine was operated both on base gasoline and on gasoline dosed with detergent additives to evaluate the effect on injector deposit formation and engine performance and emissions.
2017-10-08
Technical Paper
2017-01-2248
Haichun Ding, Wenbin Zhang, Xiao Ma, Shi-Jin Shuai, Bin Zheng, Alex Cantlay, Vinod Natarajan, Zhang Song Zhan, Bin Liu
Abstract Gasoline direct injection (GDI) engine technology is now widely used due to its high fuel efficiency and low CO2 emissions. However, particulate emissions pose one challenge to GDI technology, particularly in the presence of fuel injector deposits. In this paper, a 4-cylinder turbocharged GDI engine in the Chinese market was selected and operated at 2000rpm and 3bar BMEP condition for 55 hours to accumulate injector deposits. The engine spark timing, cylinder pressure, combustion duration, brake specific fuel consumption (BSFC), gaseous pollutants which include total hydro carbon (THC), NOx (NO and NO2) and carbon dioxide (CO), and particulate emissions were measured before and after the injector fouling test at eight different operating conditions. Test results indicated that mild injector fouling can result in an effect on engine combustion and emissions despite a small change in injector flow rate and pulse width.
2017-10-08
Technical Paper
2017-01-2255
Raul Payri, Jaime Gimeno, Santiago Cardona, Sridhar Ayyapureddi
Abstract A prototype multi-hole diesel injector operating with n-heptane fuel from a high-pressure common rail system is used in a high-pressure and high-temperature test rig capable of reaching 1100 Kelvin and 150 bar under different oxygen concentrations. A novel optical set-up capable of visualizing the soot cloud evolution in the fuel jet from 30 to 85 millimeters from the nozzle exit with the high-speed color diffused back illumination technique is used as a result of the insertion of a high-pressure window in the injector holder opposite to the frontal window of the vessel. The experiments performed in this work used one wavelength provide information about physical of the soot properties, experimental results variating the operational conditions show the reduction of soot formation with an increase in injection pressure, a reduction in ambient temperature, a reduction in oxygen concentration or a reduction in ambient density.
2017-10-08
Technical Paper
2017-01-2182
Xikai Liu, Xingyu Liang, Yonge Wu, Yuesen Wang
Abstract According to the study of the soot emission in the combustion of diesel,a new reduced mechanism for n-Heptane was constructed to describe the combustion process in diesel engine by using sensitivity analysis.Furthermore,verifying the ignition delay time in combustion process by using CHEMKIN PRO in different pressure of 13.5 atm and 42 atm, initial temperatures of 600k and equivalence ratio of 0.5 and 1.0.Then,compare the simulated results with the experiment data, the mechanisms used in the simulation were Lawrence Livermore National Laboratory (LLNL) detail mechanism and the State Key Laboratory of Engine (SKLE) mechanism.
2017-10-08
Journal Article
2017-01-2370
Matthieu Lecompte, Jerome Obiols, Jerome Cherel, Stephane Raux
Abstract Diesel Exhaust Fluid (DEF) like Adblue® is a urea/water solution injected upstream from the SCR catalyst. Urea decomposes into ammonia (NH3) which acts as reducing agent in the de-NOx reaction process. However, incomplete decomposition of urea can lead to unwanted deposits formation, thereby resulting into backpressure increase, loss of NOx reduction efficiency, and durability issues. The phenomenon is aggravated at low temperatures and can lead to restriction or stop of DEF injection below certain exhaust temperatures. This paper focuses on the influence of the additivation of DEF on deposits formation in a passenger car close-coupled SCR on filter Diesel exhaust line installed in a laboratory flow bench test. The behavior of two different additivated DEF was compared to Adblue® in terms of deposits formation on the mixer and SCRF canning at different temperatures comprised between 240°C and 165°C, and different air flows.
2017-10-08
Technical Paper
2017-01-2369
Prakash Arunachalam, Martin Tuner, Per Tunestal, Marcus Thern
Abstract Humid air motor (HAM) is an engine operated with humidified inlet charge. System simulations study on HAM showed the waste heat recovery potential over a conventional system. An HAM setup was constructed, to comprehend the potential benefits in real-time, the HAM setup was built around a 13-litre six cylinder Volvo diesel engine. The HAM engine process is explained in detail in this paper. Emission analysis is also performed for all three modes of operation. The experiments were carried out at part load operating point of the engine to understand the effects of humidified charge on combustion, efficiency, and emissions. Experiments were conducted without EGR, with EGR, and with humidified inlet charge. These three modes of operation provided the potential benefits of each system. Exhaust heat was used for partial humidification process. Results show that HAM operation, without compromising on efficiency, reduces NOx and soot significantly over the engine operated without EGR.
2017-10-08
Technical Paper
2017-01-2371
Hiroki Kambe, Naoto Mizobuchi, Eriko Matsumura
Abstract Diesel Particulate filter (DPF) is installed as after treatment device of exhaust gas in diesel engine, and collects the Particulate Matter (PM). However, as the operation time of engine increases, PM is accumulated in the DPF, resulting in deterioration of PM collection efficiency and increasing in pressure loss. Therefore, Post injection has been attracted attention as DPF regeneration method for burning and removing PM in DPF. However, Post injection causes oil dilution when fuel is injected at the middle to late stage of expansion stroke. Oil dilution are concerned to deteriorate the sliding property of piston and the thermal efficiency. For this reason, it is necessary to elucidate the mechanism and the behavior that spray impinges lubricating oil film. Therefore, in this study, we aimed to construct model of Computational Fluid Dynamics (CFD) that predicts amount of oil dilution which is concern for post injection in diesel engine, with high accuracy.
2017-10-08
Technical Paper
2017-01-2381
Kristian Hentelä, Ossi Kaario, Vikram Garaniya, Laurie Goldsworthy, Martti Larmi
In the present study, a new approach for modelling emissions of coke particles or cenospheres from large diesel engines using HFO (Heavy fuel oil) was studied. The model used is based on a multicomponent droplet mass transfer and properties model that uses a continuous thermodynamics approach to model the complex composition of the HFO fuel and the resulting evaporation behavior of the fuel droplets. Cenospheres are modelled as the residue left in the fuel droplets towards the end of the simulation. The mass-transfer and fuel properties models were implemented into a cylinder section model based on the Wärtsilä W20 engine in the CFD-code Star CD v.4.24. Different submodels and corresponding parameters were tuned to match experimental data of cylinder pressures available from Wärtsilä for the studied cases. The results obtained from the present model were compared to experimental results found in the literature.
2017-10-08
Journal Article
2017-01-2375
Akihiro Niwa, Shogo Sakatani, Eriko Matsumura, Takaaki Kitamura
Abstract In the urea SCR system, urea solution is injected by injector installed in the front stage of the SCR catalyst, and NOx can be purified on the SCR catalyst by using NH3 generated by the chemical reaction of urea. NH3 is produced by thermolysis of urea and hydrolysis of isocyanic acid after evaporation of water in the urea solution. But, biuret and cyanuric acid which may cause deposit are sometimes generated by the chemical reactions without generating NH3. Spray behavior and chemical reaction of urea solution injected into the tail-pipe are complicated. The purpose of this study is to reveal the spray behavior and NH3 generation process in the tail-pipe, and to construct the model capable of predicting those accurately. In this report, the impingement spray behavior is clarified by scattered light method in high temperature flow field.
2017-10-08
Technical Paper
2017-01-2378
Takayuki Ogata, Mikio Makino, Takashi Aoki, Takehide Shimoda, Kyohei Kato, Takahiko Nakatani, Koji Nagata, Claus Dieter Vogt, Yoshitaka Ito, Dominic Thier
Abstract In order to meet the challenging CO2 targets beyond 2020 despite keeping high performance engines, Gasoline Direct Injection (GDI) technology usually combined with charged aspiration is expanding in the automotive industry. While providing more efficient powertrains to reduce fuel consumption one side effect of GDI is the increased particle formation during the combustion process. For the first time for GDI from September 2014 there is a Particle Number (PN) limit in EU of 6x10 sup 12 #/km, which will be further reduced by one order of magnitude to 6x10 sup 11 #/km effective from September 2017 to be the same level as applied to Diesel engines. In addition to the PN limit of the certification cycle NEDC further certification of Real Driving Emissions (RDE) including portable PN measurements are under discussion by the European Commission. RDE test procedure requires stable and low emissions in a wide range of engine operations and durable over a distance of 160 000 km.
2017-10-08
Technical Paper
2017-01-2399
Jianyu Duan, Kai Sun, Lei Li
Abstract Particulate matter emissions have become a concern for the development of DISI engines. EGR has been extensively demonstrated as a beneficial technology to migrate knock performance, improve fuel economy and reduce NOX emissions. Recently, the effect of EGR on particulate matter emissions is attracting increased attention. This work investigates the effects of EGR on PN emissions with the variations of engine operating parameters and aims to understand the role of EGR in PN emissions for DISI engines. A 1.8liter turbocharged engine with cooled EGR is used for this study. The engine is operated at steady-state conditions with EGR under various operating parameters including injection timing, excess air ratio, and spark timing to characterize the particle number emissions. The results indicates that there is a high sensitivity of PN emissions to EGR with the variations of those parameters.
2017-10-08
Journal Article
2017-01-2400
Yanlong Wu, Jason Ferns, Hu Li, Gordon Andrews
Abstract Hydrogenated Vegetable Oil (HVO) diesel fuels have the potential to provide a reduced carbon footprint for diesel engines and reduce exhaust emissions. Therefore, it is a strong candidate for transport and diesel powered machines including electricity generators and other off-road machines. In this research, a waste cooking oil derived HVO diesel was investigated for its combustion and emission performance including ignition delays, size segregated particulate number emissions and gaseous emissions. The results were compared to the standard petroleum diesel. A EURO5 emission compliant three litre, direct injection, intercooled IVECO diesel engine equipped with EGR was used which has a maximum power output of 96kW. The engine was equipped with an integrated DOC and DPF aftertreatment system. Both the upstream and downstream of the aftertreatment emissions were measured. The tests were conducted at different RPM and loads at steady state conditions.
2017-10-08
Technical Paper
2017-01-2401
Elana Chapman, Pat Geng, Yaowei Zhao, Susan Zhang, JunJun Ma, Jianqiang Gong
Abstract The impact of gasoline composition on vehicle particulate emissions response has been widely investigated and documented. Correlation equations between fuel composition and particulate emissions have also been documented, e.g. Particulate Matter Index (PMI) and Particulate Evaluation Index (PEI). Vehicle PM/PN emissions correlate very well with these indices. In a previous paper, global assessment with PEI on fuel sooting tendency was presented [1]. This paper will continue the previous theme by the authors, and cover China gasoline in more detail. With air pollution an increasing concern, along with more stringent emission requirements in China, both OEMs and oil industries are facing new challenges. Emissions controls require a systematic approach on both fuels and vehicles. Chinese production vehicle particulate emissions for a range of PEI fuels are also presented.
2017-10-08
Technical Paper
2017-01-2402
Yoshinori Otsuki, Shigemi Tochino, Kenji Kondo, Kazuhiko Haruta
Abstract Fine particle emissions from engine exhaust have attracted attention because of concern of their higher deposition fraction in alveoli. Since it was observed that sizes of solid particles in exhaust of conventional internal combustion engine technologies are mainly distributed above 30 nm and the mainly irreproducible sensitivity to volatile particles can be reduced, the current solid particle number (PN) measurement methodology was targeted to PN emissions particles larger than 23 nm. The necessity of the measurement of particles smaller than 23 nm is now under discussion. It is also surmised that there is difference between emissions under regulatory defined test cycles and real driving conditions. Currently, implementation of further real driving emission regulations utilizing portable emissions measurement systems (PEMS) is in place for the EU and being actively discussed in other regions.
2017-10-08
Technical Paper
2017-01-2395
Arjun Prakash, Allen Aradi, William Imoehl, Phil Armitage
The impact of fuel composition (ethanol and aromatic content) and injector design on particulate number generation was studied in a 1.0L displacement direct injection spark ignition engine. Two types of engine tests that mimic real-life vehicle operation were carried out using a matrix of eight fuels and two injectors. It was found that the DISI injector design had the biggest impact on the extent of particulate number generation. An injector prototype designed to meet Euro 6c specifications for PN (6*1011 particles/km) resulted in much lower PN values compared to those obtained using a production injector currently available in the market. The impact of fuel composition on PN was apparent only during engine operation with the production injector. Overall, qualitative trends were observed but no statistically significant differences were observed for the impact of ethanol (E10 fuel match-blended for aromatics and octane quality) and aromatic content (19-28%) variation.
2017-10-08
Technical Paper
2017-01-2396
Fushui Liu, Yang Hua, Han Wu, Xu He, Ning Kang
Abstract Soot emission, known as PM (particulate matter), is becoming a big issue for GDI engines as the emission regulations being increasingly stricter. It is found that ethanol, as an oxygenated bio-fuel, can reduce the soot emission when added to gasoline. In order to fully understand the effect of ethanol on soot reducing, the soot characteristics of ethanol/gasoline blends were studied on laminar diffusion flames. In this experiment, the blending ratio of ethanol/gasoline was set as E0/20/40/60/80. Considering the carbon content decreasing due to ethanol addition, carbon mass flow rate was remained constant. The two-dimensional distributions of soot volume fraction were measured quantitatively by using two-color laser induced incandescence technique. The results showed that ethanol is able to decrease the soot significantly, but the effect of ethanol on soot reduction is weakened with the increasing ethanol ratio.
2017-10-08
Technical Paper
2017-01-2397
Zhan Gao, Lei Zhu, Xinyao Zou, Chunpeng Liu, Zhen Huang
Abstract Biodiesel is a potential alternative fuel which can meet the growing need for sustainable energy. Partially premixed compression ignition (PPCI) is an important low-temperature combustion strategy to reduce NOx and soot emission of diesel engines. To investigate partial premixing impact on particle formation in flames of biodiesel or biodiesel surrogates, an experimental study was performed to compare the soot morphology and nanostructure evolution in laminar co-flow methyl decanoate non-premixed flame (NPF) and partially premixed flame (PPF). The thermophoretic sampling technique was used to capture particles along flame centerlines. Soot morphology information and volume fraction were obtained from TEM analysis and nanostructure features were evaluated by HR-TEM. With primary equivalence ratio of 19, gas temperature of PPF is higher along flame centerline compared with NPF. The results show an initially stronger sooting tendency in PPF at lower positions.
2017-10-08
Technical Paper
2017-01-2398
Bei Liu, Xiaobei Cheng, Jialu Liu, Han Pu, Li Yi
Abstract Partially-premixed low-temperature combustion avoids the soot and NOx generation area on the Ф-T diagram to reduce both engine NOx and soot emissions. Compared with the HCCI combustion mode, partially-premixed combustion (PPC) has better combustion controllability. The purpose of controlling the combustion phase can be achieved by adjusting injection timing and strategy. Based on a 4 cylinder turbocharged diesel engine, this paper aims at investigating the influence of injection strategy to the engine combustion and emission formation under the condition of single injection and split injection PPC strategy respectively, in which the primary purpose focus on the emission characteristics of particles. Results show that the early-injection PPC formed by single injection can reduce the quantity, quality and geometric mean diameter (GMD) of particles obviously.
2017-10-08
Technical Paper
2017-01-2403
Yanzhao An, R Vallinayagam, S Vedharaj, Jean-Baptiste Masurier, Alaaeldin Dawood, Mohammad Izadi Najafabadi, Bart Somers, Bengt Johansson
Abstract In-cylinder visualization, combustion stratification, and engine-out particulate matter (PM) emissions were investigated in an optical engine fueled with Haltermann straight-run naphtha fuel and corresponding surrogate fuel. The combustion mode was transited from homogeneous charge compression ignition (HCCI) to conventional compression ignition (CI) via partially premixed combustion (PPC). Single injection strategy with the change of start of injection (SOI) from early to late injections was employed. The high-speed color camera was used to capture the in-cylinder combustion images. The combustion stratification was analyzed based on the natural luminosity of the combustion images. The regulated emission of unburned hydrocarbon (UHC), carbon monoxide (CO) and nitrogen oxides (NOX) were measured to evaluate the combustion efficiency together with the in-cylinder rate of heat release.
2017-10-08
Journal Article
2017-01-2298
Charles S. Shanahan, S. Scott Smith, Brian D. Sears
Abstract The ubiquity of gasoline direct injection (GDI) vehicles has been rapidly increasing across the globe due to the increasing demand for fuel efficient vehicles. GDI technology offers many advantages over conventional port fuel injection (PFI) engines, such as improvements in fuel economy and higher engine power density; however, GDI technology presents unique challenges as well. GDI engines can be more susceptible to fuel injector deposits and have higher particulate emissions relative to PFI engines due to the placement of the injector inside the combustion chamber. Thus, the need for reliable test protocols to develop next generation additives to improve GDI vehicle performance is paramount. This work discloses a general test method for consistently fouling injectors in GDI vehicles and engines that can accommodate multiple vehicle/engine types, injector designs, and drive cycles, which allows for development of effective GDI fuel additives.
2017-10-08
Journal Article
2017-01-2299
Susumu Nagano, Nozomi Yokoo, Koji Kitano, Koichi Nakata
Abstract The effects of high boiling point fuel additives on deposits were investigated in a commercial turbocharged direct injection gasoline engine. It is known that high boiling point substances have a negative effect on deposits. The distillation end points of blended fuels containing these additives may be approximately 15°C higher than the base fuel (end point: 175°C). Three additives with boiling points between 190 and 196°C were examined: 4-tert-Butyltoluene (TBT), N-Methyl Aniline (NMA), and 2-Methyl-1,5-pentanediamine (MPD). Aromatics and anilines, which may be added to gasoline to increase its octane number, might have a negative effect on deposits. TBT has a benzene ring. NMA has a benzene ring and an amino group. MPD, which has no benzene ring and two amino groups, was selected for comparison with the former two additives.
2017-10-08
Technical Paper
2017-01-2323
Lei Li, Kai Sun, Jianyu Duan
Abstract Butanol is a promising alcohol fuel. Previous studies on combustion and diesel engines showed different trends in sooting tendencies of the butanol isomers (n-butanol, iso-butanol, sec-butanol and tert-butanol).The impact of butanol isomers on the particulate emissions of GDI (Gasoline Direct Injection) engines, however, has not been reported. This work examines the combustion performance and particle number emissions of a GDI engine fueled with gasoline/butanol blends in steady state modes. Each isomer was tested at blend ratios from 10% to 50% by volume. Spark timings for all the fuels are set to obtain the maximum break torque (MBT), i.e. the MBT spark timings. Results show that the particle number concentration is reduced significantly with increasing butanol content for all the isomers.
Viewing 1 to 30 of 1567

Filter