Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 2616
2017-09-22
WIP Standard
AMS4914G
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inches in thickness. These products have been used typically in applications requiring high strength-to-weight ratio and stability up to 550 °F (288 °C), but usage is not limited to such applications. Parts are typically formed in the solution heat treated condition and subsequently precipitation heat treated to final condition.
2017-09-22
WIP Standard
AMS4919J
This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2017-09-22
WIP Standard
AMS4967M
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-20
WIP Standard
AMS2628B
This specification covers procedures for ultrasonic immersion inspection of premium grade wrought titanium and titanium alloy round billet 5.0 inches (127 mm) and over in nominal diameter. This inspection procedure has been used typically for locating internal defects such as cracks, voids, inclusions, and other structural discontinuities which may or may not be exposed to the surface in billets, but usage is not limited to such applications. Testing normally will be by longitudinal procedure, but shear wave procedure may be added when agreed upon by purchaser and vendor. This specification includes zoned inspection and digital data acquisition.
2017-09-20
WIP Standard
D17AC
This specification covers a copper-nickel-tin alloy in the form of back-extruded mechanical tube 1.100 to 13.6 inches (28 to 330 mm) in outer diameter. .
2017-09-15
WIP Standard
D17AA
This specification covers the specific requirements for 2017 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper.
2017-08-18
WIP Standard
AMS2804D
This specification covers requirements for identification of castings.
2017-07-24
WIP Standard
AMSWWT700/5B
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 5086.
2017-07-24
WIP Standard
AMSWWT700B
This specification covers the general requirements for aluminum and aluminum alloy tube; drawn, seamless (see 6.1.1). Specific requirements for these products in a particular alloy are covered by the applicable detail specification (see 6.3).
2017-06-23
WIP Standard
D17AB
This revises the Identification section of the General Agreement on Marking.
2017-05-30
WIP Standard
AMS4478A
This specification covers an aluminum alloy in the form of Alclad sheet and plate supplied in the –T81/-T851 temper. These products have been used typically for high strength parts requiring higher yield strength than is afforded by naturally aged tempers of this alloy and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.
2017-05-10
WIP Standard
AMS4403A
This specification covers an aluminum alloy in the form of die forgings 12 inches (305 mm) and under in nominal thickness and of forging stock.
2017-05-10
WIP Standard
AMS4820F
This specification covers bearings of leaded copper cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4800F
This specification covers bearings of a tin alloy cast on one or both faces of a steel or bronze backing.
2017-05-10
WIP Standard
AMS4827F
This specification covers bearings of a leaded bronze cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4463A
This specification covers an aluminum alloy in the form of plate.
2017-05-10
WIP Standard
AMS4597B
This specification covers a copper-nickel-tin alloy in the form of bars and rods.
2017-05-09
WIP Standard
AMS4329B
This specification covers an aluminum alloy in the form of plate 4.001 to 7.000 inch, incl. (101.62 to 177.80 mm, incl.) in thickness (see 8.4).
2017-05-05
WIP Standard
AMS4511B
This specification covers a copper-beryllium alloy in the form of sand, investment, or centrifugal castings.
2017-05-05
WIP Standard
AMS4842F
This specification covers a leaded bronze in the form of sand and centrifugal castings.
2017-05-05
WIP Standard
AMS7320G
This specification covers a cast leaded-tin bronze in the form of sealing rings.
2017-05-05
WIP Standard
AMS4612K
This specification covers a copper alloy (naval brass) in the form of bars and rods.
2017-05-05
WIP Standard
AMS4616G
This specification covers one type of bronze in the form of bars, rods, forgings, tubing, and forging stock.
2017-05-04
WIP Standard
AMS5221F
This specification covers an iron-nickel alloy in the form of strip.

This strip has been used typically for diaphragms, leaf springs, and helical springs, requiring a precipitation-hardenable alloy with a coefficient of modulus of elasticity of -20 to +20 x 10-6 per degree Fahrenheit from -50 to +150 degrees F (-36 to +36 x 10-6 per degree Celsius from -46 to +66 degrees C) after suitable heat treatment, but usage is not limited to such applications.

2017-05-04
WIP Standard
AMS5746G
This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings, and stock for forging or heading.

These products have been used for parts such as turbine rotors, shafts, blades, bolts, dowels, and fittings, requiring high strength up to 1600°F (871°C) and oxidation resistance up to 1800°F (982°C).

2017-05-04
WIP Standard
AMS5800G
This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire.

This wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated from alloys of similar composition, but usage is not limited to such applications.

2017-05-04
WIP Standard
AMS5382K
This specification covers a corrosion and heat-resistant cobalt alloy in the form of investment castings.
Viewing 1 to 30 of 2616

Filter

  • Standard
    2616