Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 593
2017-04-21
WIP Standard
AIR805D
The purpose of this information report is to present the factors that affect the design and development of aircraft jet blast windshield rain removal systems. Rain removal system design will generally be unique to specific aircraft. Design of these systems typically requires a preliminary design for the system based on available empirical data to be followed with a laboratory development program and a flight test validation program. Published windshield rain removal performance test data is available only for limited windshield configurations.
2017-04-10
WIP Standard
ARP1270C
This ARP covers the basic criteria for the design of cabin pressure control systems (CPCS) for general aviation, commercial and military pressurized aircraft.
CURRENT
2017-02-09
Standard
J1085_201702
These methods cover testing procedures for defining and specifying the dynamic characteristics of simple elastomers and simple fabricated elastomeric isolators used in vehicle components. Simple, here, is defined as solid (non-hydraulic) components tested at frequencies less than or equal to 25 Hz.
CURRENT
2016-11-15
Standard
J1281_201611
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.
2016-10-21
WIP Standard
AIR1609B
This SAE Aerospace Information Report (AIR) covers the design parameters for various methods of humidification applicable to aircraft, the physiological aspects of low humidities, the possible benefits of controlling cabin humidity, the penalties associated with humidification, and the problems which must be solved for practical aircraft humidification systems. The design information is applicable to commercial and military aircraft. The physiological aspects cover all aircraft environmental control applications.
2016-10-13
WIP Standard
J3130
Develop a test methodology to measure the damping performance of a composite or other bar from the frequency response function obtained from the excitation force and the corresponding acceleration level, both measured at the same point.
2016-09-10
WIP Standard
AIR1811B
The purpose of this Aerospace Information Report (AIR) is to provide guidelines for the selection and design of airborne liquid cooling systems. This publication is applicable to liquid cooling systems of the closed loop type and the expendable coolant type in which the primary function is transporting of heat from its source to a heat sink. Most liquid cooling system applications are oriented toward the cooling of electronics. Liquid cooling techniques, heat sinks, design features, selection of coolants, corrosion control, and servicing requirements for these systems are presented. Information on vapor compression refrigeration systems, which are a type of cooling system, is found in Reference 1.
CURRENT
2016-08-11
Standard
AIR1826A
This Aerospace Information Report (AIR) is limited in scope to the general consideration of environmental control system noise and its effect on occupant comfort. Additional information on the control of environmental control system noise may be found in 2.3 and in the documents referenced throughout the text. This document does not contain sufficient direction and detail to accomplish effective and complete acoustic designs.
CURRENT
2016-08-02
Standard
J1324_201608
This SAE Recommended Practice provides test methods for determining the characteristics of acoustical and thermal materials. Where applicable, methods of test developed by SAE and ASTM have been referenced.
CURRENT
2016-07-12
Standard
AMS3807C
This specification covers aluminum foil tape with a pressure sensitive adhesive.
CURRENT
2016-04-29
Standard
J2531_201604
New methods are available to assist in evaluating the risk of impulse noise-induced hearing loss from inflatable devices, for example, airbags and seat belt pretensioners. This document presents some background on impulse noise measurement techniques and assessment criteria. Related information relative to test details, for example, preamplifier specifications and filtering methods and criteria, will be discussed in a future recommended practice.
CURRENT
2016-04-20
Standard
J3001_201604
This procedure is applicable to modes from 500 and 13,000 Hz. The parameters measured with this procedure are defined as the damping factor, ξ for first nine vibration modes of the beam. The measurement will be done in free-free conditions and with temperature.
2016-04-01
WIP Standard
J1192
This standard established the requirements and test procedures for the operational life, corrosion resistence, and sound pressure level of motorcycle electric and electro pnuematic audible warning deveices. Test equipment, environment, and procedures are specified.
2016-03-25
WIP Standard
AS8017D
This SAE Aerospace Standard (AS) establishes minimum performance standards for new equipment anticollision light systems.
2015-12-31
WIP Standard
J670
The vehicle dynamics terminology presented herein pertains to passenger cars and light trucks with two axles and to those vehicles pulling single-axle trailers. The terminology presents symbols and definitions covering the following subjects: axis systems, vehicle bodies, suspension and steering systems, brakes, tires and wheels, operating states and modes, control and disturbance inputs, vehicle responses, and vehicle characterizing descriptors. The scope does not include terms relating to the human perception of vehicle response.
2015-12-04
WIP Standard
J2846
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a nylon or other shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated. The acoustical performance is expressed in terms of insertion loss (IL) which is described below.
2015-12-04
WIP Standard
J1355
This SAE Recommended Practice is applicable for determining the thickness of various resilient materials, such as insulating padding used in the automotive industry. This test method is intended to establish a uniform procedure for determining the thickness of various resilient thermal and acoustical insulating pad materials.
CURRENT
2015-11-24
Standard
J2641_201511
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
CURRENT
2015-11-24
Standard
J2567_201511
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
CURRENT
2015-11-10
Standard
J2805_201511
This SAE Standard is equivalent to ISO 362-1:2015 and specifies an engineering method for measuring the noise emitted by road vehicles of categories M and N under typical urban traffic conditions. It excludes vehicles of category L1, L2, L3, L4, and L5. The specifications are intended to reproduce the level of noise generated by the principal noise sources during normal driving in urban traffic. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustical environment that is obtained only in an extensive open space.
CURRENT
2015-11-10
Standard
J2889/1_201511
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations.
2015-09-14
WIP Standard
AIR1168/10A
This AIR is arranged in the following two sections: 2E - thermodynamic characteristics of working fluids, which contains thermodynamic diagrams for a number of working fluids currently in use and supplied by various industrial firms; and 2F - properties of heat transfer fluids, which contains data, primarily in graphical form, on fluids that are frequently used in fluid heat transfer loops. Other properties of the environment, gases, liquids, and solids, can be found, as follows, in AIR 1168/9: 2A-Properties of the natural environment; 2B-Properties of gases; 2C-Properties of liquids and 2D- Properties of solids.
2015-08-20
WIP Standard
AS8034C
This SAE Aerospace Standard (AS) specifies minimum performance standards for all types of Electronic Displays and Electronic Display Systems that are intended for use in the flight deck by the flightcrew in all 14 CFR Part 23, 25, 27, and 29 aircraft. The requirements and recommendations in this document are intended to apply to all installed electronic displays and electronic display systems within the flight deck, regardless of intended function, criticality, or location within the flight deck, but may also be used for non-installed electronic displays. This document provides baseline requirements and recommendations (see section 2.3 for definitions of “shall” and “should”). This document primarily addresses hardware requirements, such as electrical, mechanical, optical, and environmental. It does not address system specific functions.
CURRENT
2015-08-11
Standard
J2629_201508
SAE developed this document and associated spreadsheets at the request of automobile manufacturers to help compare products from multiple suppliers using standard data presentation formats. This document includes several preferred formats for presenting acoustical data on materials, components, systems, or vehicles. These formats cover the range of acoustical tests commonly conducted in the automotive industry. These tests follow SAE and ASTM test practices as well as vehicle specific test methods. For each test, the details of samples and test conditions can be entered into an applicable electronic spreadsheet together with the acoustical results data. These data are then linked to standard graphical display(s) for each test. All manufacturers and suppliers in this industry are encouraged to present data and results in these formats.
2015-08-01
WIP Standard
ARP4462A
This recommended practice covers the procedures and method for establishing acceptance criteria when performing Barkhausen noise testing of surface-hardened steel components to detect grinding burns (metallurgical damage caused by over-heating) in bare or chromium-plated parts. Primarily for nondestructive testing of heat treated, high strength low-alloy steel parts which have been ground, in accordance with MIL-STD-866 or commercial standard, before or after chromium plating. This test method may be used as an independent test or to confirm grinding damage detected in accordance with AMS 2440 or MIL-STD-867 in bare or chromium plated components.
2015-06-29
WIP Standard
J1400
This SAE Recommended Practice presents a test procedure for determining the airborne sound insulation performance of materials and composite layers of materials commonly found in mobility, industrial and commercial products under conditions of representative size and sound incidence so as to allow better correlation with in-use sound insulator performance. The frequency range of interest is typically 100 to 8000 Hz 1/3 octave-band center frequencies. This test method is designed for testing flat samples with uniform cross section, although in some applications the methodology can be extended to evaluate formed parts, pass-throughs, or other assemblies to determine their acoustical properties. For non-flat parts or assemblies where transmitted sound varies strongly across the test sample surface, a more appropriate methodology would be ASTM E90 (with a reverberant receiving chamber) or ASTM E2249 (intensity method with an anechoic or hemi-anechoic receiving chamber).
CURRENT
2015-04-30
Standard
J2883_201504
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.
CURRENT
2015-04-30
Standard
J1174_201504
This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the operator ear sound level for engine powered equipment under 30 kW (40 bhp). The sound levels obtained by using this procedure are representative of the sound levels generated by the equipment under typical operating conditions. It is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories or buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motorboats that are covered by other SAE Standards or Recommended Practices. This procedure does not cover handheld equipment such as chainsaws, leaf blowers, and trimmers. This SAE Recommended Practice may also be used when measuring the operator ear sound level of similar equipment powered by electricity or other power sources.
HISTORICAL
2014-12-29
Standard
J2889/1_201412
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations.
2014-11-23
WIP Standard
AS8040C
This SAE Aerospace Standard (AS) covers combustion heaters used in the following applications: a. Cabin heating (all occupied regions and windshield heating) b. Wing and empennage anti-icing c. Engine and accessory heating (when heater is installed as part of the aircraft) d. Aircraft de-icing
Viewing 1 to 30 of 593

Filter

  • Standard
    593