Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 119
CURRENT
2017-03-17
Standard
J1455_201703
The scope of this Recommended Practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment, and agricultural equipment including implements.
CURRENT
2017-02-09
Standard
J1883_201702
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
CURRENT
2016-11-15
Standard
J1281_201611
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.
CURRENT
2016-04-27
Standard
J3060_201604
This SAE Standard serves as a guide for vibration testing procedures of Automotive and Heavy Duty storage batteries.
CURRENT
2015-11-24
Standard
J2567_201511
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
CURRENT
2015-11-24
Standard
J2641_201511
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
CURRENT
2014-09-18
Standard
J1166_201409
This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle representing continuous medium to heavy work. The work cycles provide a repeatable reproduceable means to uniformly measure working machines against a “yard stick. A method to relate the time weighted average sound level at the operator station(s) to estimate operator sound exposure with part load work, supervision, and rest breaks is also provided.
CURRENT
2014-09-17
Standard
J994_201409
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self propelled work machines as defined by SAE J1116 (limited to categories of 1) construction, and 2) general purpose industrial). This purpose of this document is to define a set of performance requirements for backup alarms, independent of machine usage. The laboratory tests defined in this document are intended to provide a uniform and repeatable means of verifying whether or nor a test alarm meets the stated requirements. For on-machine requirements and test procedures, refer to SAE J 1446.
2014-02-04
WIP Standard
J1777
This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.
2013-10-02
WIP Standard
J153
These general operator precautions apply to off-road work machines as defined in SAE J1116, and Agricultural Tractors as defined in ANSI/ASAE S390, Nov 2004. These should not be considered as all inclusive for all specific uses and unique features of each particular machine. Other more specific operator precautions not mentioned herein should be covered by users of this recommended practice for each particular machine application.
2013-10-01
WIP Standard
J1533
This SAE Recommended Practice establishes a uniform test procedure for determining performance levels of operator enclosure panel type air filters on off-road, self-propelled work machines used in construction, general-purpose industrial, agriculture, and forestry as defined in SAE J1116 and equipped with an operator enclosure with a powered fresh air system.
2013-09-30
WIP Standard
J169
The purpose of this document is to establish air conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system, and since these characteristics and conditions vary greatly from one application to another, the designer must determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in this document.
CURRENT
2013-06-20
Standard
J88_201306
This SAE Standard sets forth the instrumentation and procedure to be used in measuring the exterior sound pressure levels for self-propelled off-road work machines as defined in sections 1, 3, 5 and 6 of SAE J1116. This document does not address the operation of safety devices such as backup alarms, horns, or accessories. The sound levels obtained by using the test procedures set forth in this document are repeatable and are representative of the higher range of sound levels generated by machines under actual field operating conditions. Due to the variability of field operating conditions, this data is not intended to be used for construction site boundary noise evaluations.
CURRENT
2013-05-31
Standard
J1782_201305
Hydraulic systems are used on marine vehicles for steering, vehicle control, and utility services. System components that generate and transmit noise are of concern. This SAE Information Report (a) addresses noise requirements which may apply to the hydraulic systems of ships and submersibles, and (b) identifies noise sources and techniques which may be used to reduce system noise. Noise of power sources (e.g., electric motors) and end items (e.g., steering linkages) is beyond the scope of this document.
CURRENT
2013-03-19
Standard
J1075_201303
This SAE Standard sets forth measurement procedures and instrumentation to be used for determining a “representative” sound level during a representative time period at selected measurement locations on a construction site boundary. The document is not intended for use in determining occupational hearing damage risk. Determination of a representative time period is left to the judgment of the user.
HISTORICAL
2012-08-24
Standard
J1455_201208
The scope of this recommended practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment and agricultural equipment including implements.
CURRENT
2012-05-17
Standard
J1454_201205
This SAE Standard describes a laboratory test procedure for comparatively evaluating the durability and fatigue life qualities of a complete seat cushion by submitting the seating surface of the cushion to repetitive compressive and rotational loading with a simulated human buttocks.
CURRENT
2012-05-11
Standard
J1175_201205
This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the bystandard sound level of engine powered equipment under 15 kW (20 bhp) typical of their normal operation. It is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories and buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motorboats that are covered by other SAE Standards or Recommended Practices. This procedure does not cover chain saws. The SAE Recommended Practice may also be used when measuring the bystander sound level on similar equipment powered by electricity or other power sources.
CURRENT
2012-01-06
Standard
J331_201201
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the sound levels of motorcycles under full throttle acceleration and closed throttle deceleration.
2011-10-11
WIP Standard
J1161
This recommended practice establishes the instrumentation, test site, and test procedure for determining the exterior operational sound level for snowmobiles.
CURRENT
2011-09-12
Standard
J366_201109
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
CURRENT
2011-09-12
Standard
J336_201109
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
CURRENT
2011-08-04
Standard
J47_201108
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the maximum sound level potential for motorcycles under wide open throttle acceleration and closed throttle deceleration.
CURRENT
2011-07-18
Standard
J34_201107
This SAE Recommended Practice establishes the procedure for measuring the maximum exterior sound level of recreational motorboats while being operated under a variety of operating conditions. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
CURRENT
2011-04-01
Standard
J2005_201104
This SAE Recommended Practice establishes the procedure for determining if recreational motorboats have effective exhaust muffling means when operating in the stationary mode. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
CURRENT
2011-02-18
Standard
J1970_201102
This SAE Recommended Practice establishes the procedure for measuring the sound level of recreational motorboats in the vicinity of a shore bordering any recreational boating area during which time a boat is operating under conditions other than stationary mode operation. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
HISTORICAL
2011-01-04
Standard
J1455_201101
The scope of this recommended practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment and agricultural equipment including implements.
HISTORICAL
2009-01-27
Standard
J2567_200901
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
HISTORICAL
2008-02-06
Standard
J1166_200802
This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: Crawler Loader Wheel Loader Dumper Tractor Scraper Grader Crawler Tractor with Dozer Wheel Tractor with Dozer Pad Foot Wheel Compactor with Dozer Backhoe Hydraulic Excavator Log Skidder Excavator and Wheel Feller-Buncher Pipelayer Roller/Compactor Trencher Sweeper The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle. A method to relate the time weighted average sound level at the operator station(s) to operator sound exposure is also provided.
CURRENT
2007-11-20
Standard
J1013_200711
This SAE Standard defines a method for the measurement of the whole body vibration to which the seated operator of off-highway self-propelled work machines is exposed while performing an actual or simulated operation. It applies to vibration transmitted to the operator through the seat. There are not equivalent ISO Standards. In the main body of this document, conditions are defined for measuring and recording whole body vibration of the seated operator of off-highway self-propelled work machines. The specification of instruments, analytic methods, and description of site and operating conditions allows the measurements to be made and reported with an acceptable precision. The procedure includes means of weighing the vibration level at different frequencies as specified in ISO2631. A standard format for reporting spectral data is recommended. The definitions, instruments, and analytic methods also apply to simulated tests for operator vibration as performed in laboratories.
Viewing 1 to 30 of 119

Filter

  • Standard
    119

Subtopics