Criteria

Text:
Content:
Display:

Results

Viewing 31 to 60 of 631
2016-04-01
WIP Standard
J1192
The requirements of this document apply to all classes of motorcycles as defined in SAE J213.
2015-12-31
WIP Standard
J670
The vehicle dynamics terminology presented herein pertains to passenger cars and light trucks with two axles and to those vehicles pulling single-axle trailers. The terminology presents symbols and definitions covering the following subjects: axis systems, vehicle bodies, suspension and steering systems, brakes, tires and wheels, operating states and modes, control and disturbance inputs, vehicle responses, and vehicle characterizing descriptors. The scope does not include terms relating to the human perception of vehicle response.
CURRENT
2015-12-20
Standard
ARP1839
This Aerospace Recommended Practice (ARP) is a general overview of typical airborne engine vibration monitoring (EVM) systems applicable to fixed or rotary wing aircraft applications, with an emphasis on system design considerations. It describes EVM systems currently in use and future trends in EVM development. The broader scope of Health and Usage Monitoring Systems, (HUMS) is covered in SAE documents AS5391, AS5392, AS5393, AS5394, AS5395, AIR4174. This ARP also contains the essential elements of AS8054 which remain relevant and which have not been incorporated into Original Equipment Manufacturers (OEM) specifications.
CURRENT
2015-12-06
Standard
AS6254A
This SAE Aerospace Standard (AS) covers ULDs utilized in finding submerged aircraft. Such ULDs are installed within the aircraft in a manner that they are unlikely to become separated during crash conditions. The low frequency ULD should be attached to the airframe in accordance with the manufacturer’s recommendations in order to maximize the underwater detection range. ARINC Standard 677 also provides installation guidance for Low Frequency ULDs.
CURRENT
2015-11-24
Standard
J2567_201511
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
CURRENT
2015-11-24
Standard
J2641_201511
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
CURRENT
2015-11-10
Standard
J2889/1_201511
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations.
CURRENT
2015-11-10
Standard
J2805_201511
This SAE Standard is equivalent to ISO 362-1:2015 and specifies an engineering method for measuring the noise emitted by road vehicles of categories M and N under typical urban traffic conditions. It excludes vehicles of category L1, L2, L3, L4, and L5. The specifications are intended to reproduce the level of noise generated by the principal noise sources during normal driving in urban traffic. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustical environment that is obtained only in an extensive open space.
2015-10-02
WIP Standard
J3111
The scope of this recommended practice is to establish definitions and recommended methods for the measurement of lateral run-out and disc thickness variation in the laboratory and vehicle for passenger cars and light duty trucks up to 4546 kg gross vehicle weight. This recommended practice will breakdown the instrumentation (sensors and sizes), test setup, and data processing.
CURRENT
2015-09-02
Standard
J577_201509
This SAE Recommended Practice provides procedures, and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
2015-08-20
WIP Standard
AS8034C
This SAE Aerospace Standard (AS) specifies minimum performance standards for all types of Electronic Displays and Electronic Display Systems that are intended for use in the flight deck by the flightcrew in all 14 CFR Part 23, 25, 27, and 29 aircraft. The requirements and recommendations in this document are intended to apply to all installed electronic displays and electronic display systems within the flight deck, regardless of intended function, criticality, or location within the flight deck, but may also be used for non-installed electronic displays. This document provides baseline requirements and recommendations (see section 2.3 for definitions of “shall” and “should”). This document primarily addresses hardware requirements, such as electrical, mechanical, optical, and environmental. It does not address system specific functions.
CURRENT
2015-08-11
Standard
J2629_201508
SAE developed this document and associated spreadsheets at the request of automobile manufacturers to help compare products from multiple suppliers using standard data presentation formats. This document includes several preferred formats for presenting acoustical data on materials, components, systems, or vehicles. These formats cover the range of acoustical tests commonly conducted in the automotive industry. These tests follow SAE and ASTM test practices as well as vehicle specific test methods. For each test, the details of samples and test conditions can be entered into an applicable electronic spreadsheet together with the acoustical results data. These data are then linked to standard graphical display(s) for each test. All manufacturers and suppliers in this industry are encouraged to present data and results in these formats.
2015-08-01
WIP Standard
ARP4462A
This recommended practice covers the procedures and method for establishing acceptance criteria when performing Barkhausen noise testing of surface-hardened steel components to detect grinding burns (metallurgical damage caused by over-heating) in bare or chromium-plated parts. Primarily for nondestructive testing of heat treated, high strength low-alloy steel parts which have been ground, in accordance with MIL-STD-866 or commercial standard, before or after chromium plating. This test method may be used as an independent test or to confirm grinding damage detected in accordance with AMS 2440 or MIL-STD-867 in bare or chromium plated components.
CURRENT
2015-04-30
Standard
J1174_201504
This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the operator ear sound level for engine powered equipment under 30 kW (40 bhp). The sound levels obtained by using this procedure are representative of the sound levels generated by the equipment under typical operating conditions. It is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories or buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motorboats that are covered by other SAE Standards or Recommended Practices. This procedure does not cover handheld equipment such as chainsaws, leaf blowers, and trimmers. This SAE Recommended Practice may also be used when measuring the operator ear sound level of similar equipment powered by electricity or other power sources.
CURRENT
2015-04-30
Standard
J2883_201504
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.
CURRENT
2015-04-15
Standard
J2455_201504
Product for which data is to be available is for class 6 and larger, i.e., gross vehicle weight > 9.6 kg (19 500 lb).
HISTORICAL
2014-12-29
Standard
J2889/1_201412
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations.
2014-11-23
WIP Standard
AS8040C
This SAE Aerospace Standard (AS) covers combustion heaters used in the following applications: a. Cabin heating (all occupied regions and windshield heating) b. Wing and empennage anti-icing c. Engine and accessory heating (when heater is installed as part of the aircraft) d. Aircraft de-icing
CURRENT
2014-09-18
Standard
J1166_201409
This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle representing continuous medium to heavy work. The work cycles provide a repeatable reproduceable means to uniformly measure working machines against a “yard stick. A method to relate the time weighted average sound level at the operator station(s) to estimate operator sound exposure with part load work, supervision, and rest breaks is also provided.
CURRENT
2014-09-17
Standard
J994_201409
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self propelled work machines as defined by SAE J1116 (limited to categories of 1) construction, and 2) general purpose industrial). This purpose of this document is to define a set of performance requirements for backup alarms, independent of machine usage. The laboratory tests defined in this document are intended to provide a uniform and repeatable means of verifying whether or nor a test alarm meets the stated requirements. For on-machine requirements and test procedures, refer to SAE J 1446.
CURRENT
2014-08-13
Standard
J184_201408
Various SAE vehicle sound level measurement procedures require use of a sound level meter which meets the Type 1 or Type 2 requirements of ANSI S1.4-1983 (see 2.1.1.1), or an alternative system which can be proved to provide equivalent test data. The purpose of this SAE Recommended Practice is to provide a procedure for determining if a sound data acquisition system (SDAS) has electro-acoustical performance equivalent to such a meter. By assuring equivalent performance of the test instrumentation, the equivalence of test data is assured. Two general configurations of sound data acquisition systems will be encompassed (see Figure 1). The first configuration consists of instrument sections which perform as a sound level meter. The second configuration is a system which records data for later processing. The intent of this document is to establish guidelines which permit the test engineer to insure equivalence of sound data acquisition systems to a sound level meter.
CURRENT
2014-07-01
Standard
AIR4362A
This SAE Aerospace Information Report (AIR) provides Nuclear, Biological and Chemical (NBC) protection considerations for environmental control system (ECS) design. It is intended to familiarize the ECS designer with the subject in order to know what information will be required to do an ECS design where NBC protection is a requirement. This is not intended to be a thorough discussion of NBC protection. Such a document would be large and would be classified. Topics of NBC protection that are more pertinent to the ECS designer are discussed in more detail. Those of peripheral interest, but of which the ECS designer should be aware are briefly discussed. Only radiological aspects of nuclear blast are discussed. The term CBR (Chemical, Biological, and Radiological) has been used to contrast with NBC to indicate that only the radiological aspects of a nuclear blast are being discussed.
CURRENT
2014-06-06
Standard
J671_201406
The materials classified under this specification are: Mastic vibration damping materials used to reduce the sound emanating from metal panels. Mastic underbody coatings used to give protection and some vibration damping to motor vehicle underbodies, fenders, and other parts.
CURRENT
2014-05-16
Standard
J1060_201405
This SAE Recommended Practice establishes a rating scale for subjective evaluations of noise and discomfort in motor vehicles. Through test procedures utilizing specific vehicles on specific roads, the scale may be utilized to assess the relative contributions of tires to noise and discomfort. The noise and ride comfort characteristics attributed to automotive tires have traditionally been estimated by subjectively assigning number designations (commonly on a 1 to 10 scale) to the audible and tactile sensations observed while traversing a given road course in a vehicle equipped with the tires under evaluation. Regardless of advances in objective measurements of tire properties related to noise and discomfort, subjective evaluation will continue to be necessary for the purpose of establishing the significance of such measurements.
CURRENT
2014-05-16
Standard
J57_201405
This procedure provides for the measurement of the sound generated by a test tire, mounted on a single-axle trailer, operated at multiple speeds.
CURRENT
2014-05-16
Standard
J1207_201405
This SAE Recommended Practice sets forth the instrumentation, environment, and test procedures to be used in measuring the silencer system effectiveness in reducing intake or exhaust sound level of internal combustion engines. The system shall include the intake or exhaust silencer, related piping, and components. This procedure is intended for engine-dynamometer testing and is not necessarily applicable to vehicle testing (see Appendix A). The effect of the exhaust or intake system on the sound level of the overall machine must be determined using other procedures. This procedure may be successively applied to various silencer configurations to determine relative effectiveness for that engine. Insertion loss for individual silencers may be calculated through measurement of the silenced and unsilenced system.
CURRENT
2014-05-16
Standard
J1074_201405
This SAE Recommended Practice sets forth the equipment, environment, and test procedures to be used in measuring sound levels of engines. The purpose is to provide a uniform method of measuring the maximum acoustical radiation from the exterior surfaces of an engine under representative engine operating conditions. The measured sound levels will be useful in development of engines, comparison of engines, and installation of engines in various applications. The correlation of the measured engine sound levels to the various application sound levels will have to be developed.
2014-03-25
WIP Standard
J1477
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis.
2014-03-06
WIP Standard
AIR6501
To provide a method that accounts for the attenuation due to line-of-sight blockage of aircraft noise by terrain features.
2014-02-04
WIP Standard
J1777
This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.
Viewing 31 to 60 of 631

Filter

  • Standard
    631

Subtopics