Criteria

Text:
Content:
Display:

Results

Viewing 241 to 270 of 1030
2013-12-06
Article
If smaller and thinner particles can be aligned in a certain way, it may be possible for a battery to hold a charge 50% longer than current batteries can.
2013-12-05
Article
AEI is not a publication that would normally embrace road impressions of a vehicle: the extraordinary Volkswagen XL1 is a very rare exception.
2013-12-04
Article
While shifting the manufacturing process of a composite part from pre-impregnated to a new liquid resin injection process, the Composites Development team at Bombardier Aerospace had to redesign the component to a new set of design allowables. The Integrated Product Development Team was able to quickly provide a turnkey solution that resulted in a positive business case for both weight and cost.
2013-12-02
Article
Millbrook Proving Ground in the U.K. has introduced a Portable Emissions Measurement System (PEMS).
2013-11-26
Article
UniWest has expanded the EddyView family with three portable eddy current testing instruments: the Prime, Pro, and Premium instruments are off-the-shelf and readily available.
2013-11-26
Article
Asylum Research’s blueDrive photothermal excitation is available on its Cypher atomic force microscopes.
2013-11-26
Article
ARPA-e targets "robust" batteries that not only bear loads but also absorb crash-impact energy to save weight.
2013-11-24
Article
Researchers devised the tests to prove that active flow control can enhance the performance of a vertical tail enough to allow future designers to reduce the size of the structure for a whole family of airplanes.
2013-11-22
Article
Now that simulation and modeling are common techniques for designing equipment, standards groups are stepping in to add a bit more structure and compatibility for these tools. Two trade associations have paired up to establish a working group that aims to make it simpler to merge engineering analysis with overall systems behavior analysis.
2013-11-13
Article
A forum at the 2013 SEMA Show discussed three approaches to ensure performance parts compliance with federal safety standard No. 126. Panelists also explained how simulation data, and kinematics and compliance measurements, can improve performance parts design.
2013-11-12
Article
MESSRING offers the new M=BUS in-dummy data acquisition system for the WorldSID (Worldwide Harmonized Side Impact Dummy) 5th Small Female Dummy.
2013-10-31
Article
New R-1234yf production is promised by Arkema. SAE Cooperative Research Group shows R-445A blend has potential, and vehicle prototype charging equipment for assembly line and service shop is undergoing testing. German automakers resurrect the R-744 (carbon dioxide as a refrigerant) development program.
2013-10-31
Article
Combustion simulation has the potential to help engine manufacturers design better engines in less time with less cost.
2013-10-30
Article
In an attempt to achieve a balance between Reynolds number, model scale, and tunnel blockage issues, a 1:3 scale heavy-vehicle testing program has been initiated at the Monash University 1.4-MW wind tunnel.
2013-10-30
Article
Ashok Leyland, the Hinduja Group flagship, has sold Defiance Testing & Engineering Services (DTE) to Exova, a provider of testing, calibration, and advisory services. Located near Detroit, DTE was acquired by Ashok Leyland in 2007 and since has experienced consistent and profitable growth, according to the Indian OEM, through a combination of operational efficiency, new customer capture, and focus on adjacent sectors such as construction and off-highway, and defense.
2013-10-24
Article
Durex Industries’ Chiller Technology-based aluminum nitride (AlN) ceramic heater with an embedded tungsten RTD (resistance temperature detector) sensor can heat from 100° to 450°C at 200°C/s, as well as cool from 450° to 100°C at 100°C/s.
2013-10-24
Article
Mars Labs, LLC’s Titan modular DAQ system, available in both standard and custom models, can be used for durability and fatigue, noise and vibration, shock, compression, and acoustics measurements.
2013-10-21
Article
Next-generation unmanned air systems will require more performance and must integrate increasing capabilities for guidance control, weaponry, and surveillance—all in a very limited space.
2013-10-10
Article
Ford is helping to make its vision of driverless parallel parking and pedestrian avoidance realities. The automaker demonstrated the two technologies to journalists earlier this week at its proving grounds in Lommel, Belgium.
2013-10-04
Article
NH Research Inc. offers a 40-V model as a part of its 9200 family of high-power battery charge/discharge test systems.
2013-10-01
Article
Expanding on a demonstration project in Hawaii, General Motors Co. and the U.S. Army Tank Automotive Research, Development & Engineering Center (TARDEC) will again collaborate on fuel-cell technology under a new cooperative research and development agreement.
2013-10-01
Article
Meritor offers two lightweight electronic systems that allow drivers to control tire pressure, differential locking, and transfer case positioning to improve military vehicle performance and traction in various terrains and extreme conditions.
2013-10-01
Article
Maplesoft adds the MapleSim hydraulics library to its product family through a technology partnership with Modelon.
2013-10-01
Article
Meggitt Sensing Systems’ Endevco model 7253D triaxial Isotron accelerometer is designed for applications requiring the measurement of shock and vibration simultaneously in three mutually perpendicular axes.
2013-09-23
Article
Southwest Research Institute says it has deployed the first electric-vehicle aggregation system using SAE International’s J1772 standard for dc fast charging. The system, part of the Smart Power Infrastructure Demonstration for Energy Reliability and Security (SPIDERS) Phase II program, is controlling five fast-charge stations at the Fort Carson Army Base in Colorado Springs, CO.
2013-09-18
Article
Rising system complexity and shortened development cycles have led to the need for an extension of the existing, classical test methods. The Airbus High Lift Test Department is pursuing virtual testing as an additional, equivalent test means besides existing, established physical means of compliance.
2013-09-17
Article
Napoleon Engineering Services (NES) announces a custom test rig design and manufacturing service for OEMs to perform rigorous bearing testing in-house.
2013-09-13
Article
The U.S. Department of Energy recently opened what it describes as a "one-of-a-kind national secure data center" at its National Renewable Energy Laboratory (NREL) in Golden, CO. The National Fuel Cell Technology Evaluation Center (NFCTEC) allows industry, academia, and government organizations to submit and review data gathered from projects to advance cost-effective fuel-cell technology.
2013-09-09
Article
Danlaw Inc. offers its Mx-Suite embedded software test product with seamless connectivity to National Instruments’ NI VeriStand, the environment for configuring real-time testing applications.
2013-09-04
Article
The Trimble TirePulse tire monitoring system was designed to reduce maintenance costs, increase overall fleet productivity, and promote site safety.
Viewing 241 to 270 of 1030

Filter

  • Article
    1030