Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 241 to 270 of 20000
CURRENT
2016-12-12
Standard
AS63480AR-3
No Scope available.
CURRENT
2016-12-12
Standard
ARP5448/7A
This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a. Destructive Inspection - Cut and measure (not applicable to molded liners) b. Nondestructive Inspection - Radial play (gauge) measurement
CURRENT
2016-12-12
Standard
AMS6265P
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-12
Standard
AMS6484E
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-12
Standard
AMS6414M
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-07
Standard
AMS6304M
This specification covers an aircraft quality, low alloy, heat resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-07
Standard
J1677_201612
This SAE Standard is intended to establish uniform methods for testing certain types of carbon steel and high strength, low alloy steel tubing as listed in section 2.1.1. The specified test and performance criteria applicable to each variety of tubing are set forth in the respective SAE J Specifications.
CURRENT
2016-12-07
Standard
AMS6415U
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-06
Standard
AMS4962B
This specification covers a premium grade titanium alloy in the form of investment castings.
CURRENT
2016-12-06
Standard
AMS4909K
This specification covers a titanium alloy in the form of sheet, strip, and plate up to 1.000 inch (25.40 mm) inclusive.
CURRENT
2016-12-06
Standard
AMS6409E
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-12-06
Standard
AMST81915B
This specification prescribes the requirements for Titanium and Titanium-alloy castings produced by the investment casting process.
CURRENT
2016-12-01
Standard
ARP5369B
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
2016-11-30
WIP Standard
J361
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
CURRENT
2016-11-29
Standard
AMS2636A
This specification covers procedures for ultrasonic immersion inspection of premium grade wrought titanium and titanium alloy forgings. Premium grade is a term used to describe titanium alloys used for critical rotating components in turbine engines. For details, see SAE AMS2380, the specification that covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products.
CURRENT
2016-11-29
Standard
AMS2451/3B
This specification covers the requirements for brush plating of low-hardness, low-stress nickel by electrodeposition.
CURRENT
2016-11-29
Standard
AMS6487L
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
CURRENT
2016-11-28
Standard
J891_201611
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
CURRENT
2016-11-28
Standard
AMS4174E
This specification covers an aluminum alloy in the form of flash welded rings 0.062 to 4.499 inches, incl (1.57 to 114.27 mm incl) in radial thickness, with cross sectional areas up to 32 in2 (206 cm2) (see 8.5).
CURRENT
2016-11-28
Standard
AMS4212L
This specification covers an aluminum alloy in the form of castings.
CURRENT
2016-11-23
Standard
AIR4069C
This SAE Aerospace Information Report (AIR) presents preferred design, assembly, and repair practices for sealing of aircraft integral fuel tanks, including rework of applied fuel tank seals. It addresses engineering designs for integral fuel tanks as they are currently found in practice; and discusses the most practical and conservative methods for producing a reliable, sealed system. Although this AIR presents practices for sealing of integral fuel tanks, the practices presented within this report are practices that are carried throughout sealing that include both pressure and environmental aircraft sealing. Design preferences for optimum sealing are not within the scope of this document. Such discussions can be found in the United States Air Force (USAF) sponsored report, entitled Aircraft Integral Fuel Tank Design Handbook, AFWAL-TR-87-3078.
CURRENT
2016-11-23
Standard
J492_201611
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
CURRENT
2016-11-23
Standard
AMS6255F
This specification covers a premium aircraft quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2016-11-23
Standard
J892_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.
CURRENT
2016-11-23
Standard
AMS5666J
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, extrusions, flash welded rings, and stock for forging, extruding, or flash welded rings up to 10 inches (254 mm) in diameter or least cross-sectional dimension (see 8.5).
CURRENT
2016-11-22
Standard
AMS5441B
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings 5 inches (127 mm) and under in nominal diameter or least distance between parallel sides and up to 50 in2 (323 cm2) in cross-sectional area, and stock of any size for forging, flash welded rings, or heading (see 8.5).
CURRENT
2016-11-22
Standard
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
CURRENT
2016-11-21
Standard
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
CURRENT
2016-11-21
Standard
J430_201611
These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.
Viewing 241 to 270 of 20000