Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 181 to 210 of 20078
2017-03-15
WIP Standard
AMS1548B
This specification covers a solvent-emulsion cleaner in the form of a solvent-base liquid concentrate.
CURRENT
2017-03-15
Standard
AIR6172A
This test method provides stakeholders (runway deicing chemical manufacturers, users, regulators and airport authorities) with relative ice undercutting capacity of runway deicing chemicals, by measuring the area of ice undercut pattern as a function of time. Such runway deicing chemicals are often also used on taxiways and other paved areas. This test method does not quantitatively measure the theoretical or extended time of ice undercutting capability of ready-to-use runway deicing/anti-icing chemicals in liquid or solid form.
CURRENT
2017-03-15
Standard
J2302_201703
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
2017-03-14
WIP Standard
J1942
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 1991, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
CURRENT
2017-03-14
Standard
AMS4079H
This specification covers an aluminum alloy in the form of drawn, round, seamless tubing with wall thickness of 0.018 to 0.500 inch (0.46 to 12.70 mm), inclusive (see 8.5).
2017-03-13
WIP Standard
AMS3056C
This specification covers the requirements for a refined paraffinic petroleum-base lubricant. Primarily as a lubricant in spin axis bearings of gyroscopes, accelerometers, and similar bearing applications.
2017-03-13
WIP Standard
ARP5316E
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life.

The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents.

CURRENT
2017-03-10
Standard
J2762_201703
This Standard provides an overview of results and requirements needed to remove refrigerant from a mobile air conditioning system for determining refrigerant emissions (leakage). This reclaim procedure for use on fleet vehicles in a field service environment should produce an accuracy and repeatability sufficient to determine refrigerant loss within 2 g.
CURRENT
2017-03-08
Standard
AMS2418J
This specification covers the requirements for electrodeposited copper.
CURRENT
2017-03-07
Standard
AMS4473A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch (19.05 to 38.10 mm), inclusive, in nominal thickness.
2017-03-06
WIP Standard
AMS3217/2D
This specification covers a standard acrylonitrile butadiene (NBR-L) rubber stock with low acrylonitrile content in the form of molded test slabs.
2017-03-06
WIP Standard
AMS3222J
This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
2017-03-05
WIP Standard
AMS4303C
This specification covers an aluminum alloy in the form of plate.
2017-03-05
WIP Standard
AMS4307C
This specification covers an aluminum alloy in the form of extruded bars, rods, profiles, and tubing.
2017-03-05
WIP Standard
AMS4275E
This specification has been declared NONCURRENT by the Aerospace Materials Division, SAE, as of April 1989. It is recommended that this specification not be specified for new designs.
CURRENT
2017-03-03
Standard
AMS2368D
This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products, except forgings and forging stock. It is applicable to the extent specified in a material specification.
2017-03-02
WIP Standard
AMS6532G
This specification covers a premium aircraft-quality alloy steel in the form of bars, forgings, and forging stock.
2017-03-02
WIP Standard
ARP1962B
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein. It describes the requirements for training and approval of personnel performing certain heat-treating and associated operations. It also establishes that only approved personnel may perform or monitor the functions listed for the processes and materials listed.
CURRENT
2017-03-02
Standard
AMS3593B
This specification covers an irradiated, thermally-stabilized, flame-resistant, modified-polyvinylidene-fluoride plastic in the form of extra-thin-wall tubing.
CURRENT
2017-03-01
Standard
AMS3582B
This specification covers a crosslinked polyvinyl chloride plastic in the form of flexible, thin-wall, heat-shrinkable tubing.
CURRENT
2017-03-01
Standard
AMS6509A
This specification covers a premium aircraft-quality alloy steel in the form of bars 199 in2 (1284 cm2) and under in cross section, forgings, and forging stock.
CURRENT
2017-03-01
Standard
AMS5916B
This specification covers a corrosion and heat-resistant alloy in the form of sheet, strip, and plate 2.00 inch (50.8 mm) and under in thickness (see 8.4).
CURRENT
2017-03-01
Standard
AMS1428J
This foundation specification (AMS1428J) and its associated category specifications (AMS1428/1 and AMS1428/2) cover three types of deicing/anti-icing fluids, each in the form of a non-Newtonian fluid.
2017-02-28
WIP Standard
AIR6919
Over the past several years the FZG A/8.3/90 test method has been used to evaluate current qualified aviation lubricants. The results of the effort have been summarized in this document as a historical reference to document the findings made from the committee.
CURRENT
2017-02-28
Standard
AMS3683B
This specification covers a thermally-stabilized, irradiated, modified fluoropolymer in the form of very-thin-wall tubing.
CURRENT
2017-02-28
Standard
AS81765A
This specification covers requirements for material used in electrical insulating heat shrinkable components. The continuous operating temperature of these materials shall range from -75°C to +200°C (-103°F to +392°F). (See 6.1).
CURRENT
2017-02-27
Standard
AMS2451/14
This specification covers the requirements for brush plating of nickel-tungsten by electrodeposition.
Viewing 181 to 210 of 20078