Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 20341 to 20370 of 20547
HISTORICAL
1942-03-01
Standard
AMS6290B
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock. These products have been used typically for carburized parts which require low minimum core hardness and allow a wide hardness range in sections 0.375 in. (9.50 mm) and under in nominal thickness, but usage is not limited to such applications. The core may or may not be machinable after hardening.
HISTORICAL
1942-03-01
Standard
AMS5120
This specification covers a carbon steel in the form of strip.
HISTORICAL
1942-03-01
Standard
AMS5010A
This specification covers a free-machining carbon steel in the form of bars.
HISTORICAL
1942-03-01
Standard
AMS6294B
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
HISTORICAL
1942-03-01
Standard
AMS6370A
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
HISTORICAL
1942-03-01
Standard
AMS2470A
This specification establishes the requirements for anodic coatings on aluminum alloys.
HISTORICAL
1942-03-01
Standard
AMS5115
This specification covers a carbon steel in the form of wire supplied as coils of wire or as finished springs. Primarily for springs, such as valve springs, subject to moderate stresses and requiring good fatigue properties.
HISTORICAL
1942-03-01
Standard
AMS6382A
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
1942-01-01
Standard
AMS4076
1. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 2. COM1POSITION: Silicon 45 to 65% of magnesium content Magnesium 1.10 - 1.40 Chromium 0.15 - 0.35 Iron 0.35 max Copper 0.10 max Titanium 0.10 max Manganese 0.10 max Zino 0.10 max Other Impurities, each 0.05 max Other Impurities, total 0.15 max Aluminum remainder
HISTORICAL
1942-01-01
Standard
AMS4815
This specification covers bearings of low-carbon steel plated on one or both faces with silver.
HISTORICAL
1942-01-01
Standard
AMS5710
This specification covers a corrosion and heat resistant steel in the form of bars, forgings, and forging stock.
HISTORICAL
1942-01-01
Standard
AMS5705
This specification has been 'CANCELLED' by the Aerospace Materials Division, SAE, as of September, 2002. Alloy: CNS UNS Number: S63005
HISTORICAL
1942-01-01
Standard
AMS4140
This specification has been declared “NONCURRENT” by the Aerospace Materials Division, SAE, as of August 2009. It is recommended, therefore, that this specification not be specified for new designs. “NONCURRENT” refers to those materials which may have been widely used previously and which may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does not recommend these specifications for future use in new designs. “NONCURRENT” specifications are available from SAE upon request.
HISTORICAL
1942-01-01
Standard
AMS4220
This specification has been "CANCELLED" by the Aerospace Materials Division, SAE, as of November 1995.
HISTORICAL
1942-01-01
Standard
AMS3226
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for hose, packings, bushings, grommets, and seals in contact with hot, petroleum-base lubricating oils and glycol-type coolants from -40 degrees to +100 degrees C (-40 degrees to +212 degrees F).
HISTORICAL
1942-01-01
Standard
AMS2450
This specification covers the procedure to be used for spraying metallic parts with aluminum and the properties of the coating.
HISTORICAL
1942-01-01
Standard
AMS3500
This specification covers leather tanned with chromium salts and retanned with vegetable tanning material.
HISTORICAL
1942-01-01
Standard
AMS2601A
This specification provides requirements and procedures for gas-pressure leak testing of parts.
HISTORICAL
1942-01-01
Standard
AMS2602
This specification provides requirements and procedures for air-pressure leak testing of parts.
HISTORICAL
1942-01-01
Standard
AMS2605
This specification provides requirements and procedures for air-pressure leak testing of parts.
HISTORICAL
1942-01-01
Standard
AMS2607
This specification provides requirements and procedures for air-pressure leak testing of parts.
HISTORICAL
1942-01-01
Standard
AMS4088
This specification covers an aluminum alloy in the form of seamless, drawn tubing.
HISTORICAL
1942-01-01
Standard
AMS2606A
This specification provides requirements and procedures for air-pressure leak testing of parts.
HISTORICAL
1942-01-01
Standard
AMS4017
This specification covers an aluminum alloy in the form of sheet and plate.
HISTORICAL
1941-11-01
Standard
AMS4210A
This specification covers an aluminum alloy in the form of sand castings.
HISTORICAL
1941-11-01
Standard
AMS4380
HISTORICAL
1941-11-01
Standard
AMS6252A
HISTORICAL
1941-11-01
Standard
AMS6253A
No scope available.
HISTORICAL
1941-11-01
Standard
AMS6254A
No scope available.
HISTORICAL
1941-11-01
Standard
AMS6242A
Viewing 20341 to 20370 of 20547