Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 19981 to 20010 of 20532
HISTORICAL
1945-05-01
Standard
AMS2202
This specification covers established manufacturing tolerances applicable to aluminum and magnesium alloy sheet and plate ordered to inch dimensions. These tolerances apply to all conditions, unless otherwise noted. The term 'excl' applies only to the higher figure of the specified range.
HISTORICAL
1945-05-01
Standard
AMS7225A
HISTORICAL
1945-05-01
Standard
AMS7210A
HISTORICAL
1945-05-01
Standard
AMS2475A
This specification establishes the requirements for chromate conversion coatings on magnesium alloys. This process has been used typically to improve corrosion resistance and adherence of organic finishes but usage is not limited to such applications. The dichromate treatment may not be suitable for alloys with high manganese content. The chrome pickle treatment has been used as touch-up for previously dichromate-treated surfaces and for improving corrosion protection temporarily, but usages are not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS2231
This specification covers established inch/pound manufacturing tolerances applicable to carbon steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl " is used to apply only to the higher figure of the specified range.
HISTORICAL
1945-05-01
Standard
AMS5575C
This specification covers a corrosion and heat-resistant steel in the form of welded tubing.
HISTORICAL
1945-05-01
Standard
AMS4071
This specification covers an aluminum alloy in the form of drawn, round seamless tubing. This tubing has been used typically for parts, such as hydraulic systems and fuel and oil lines, but usage is not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS4640A
This specification covers an aluminum bronze alloy in the form of bars, rods, shapes, tubes, forgings, and forging stock.
HISTORICAL
1945-05-01
Standard
AMS2400D
This specification covers the requirements for electrodeposited cadmium on metal parts.
HISTORICAL
1945-05-01
Standard
AMS4217A
This specification covers an aluminum alloy in the form of castings.
HISTORICAL
1945-05-01
Standard
AMS2251
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive " is used to apply only to the higher figure of the specified range.
HISTORICAL
1945-05-01
Standard
AMS5570D
This specification covers a corrosion and heat resistant steel in the form of seamless tubing. This tubing has been used typically for parts requiring both corrosion and heat resistance, especially when such parts are welded during fabrication, and also for parts requiring oxidation resistance up to 1500 degrees F (816 degrees C) but useful at that temperature only when stresses are low; usage is not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS5565A
This specification covers a corrosion-resistant steel in the form of welded tubing. This tubing has been used typically for parts, such as fluid-conducting lines not subjected to high pressure, requiring good corrosion resistance, but usage is not limited to such applications. Welding, brazing, or other exposure to temperatures over 800 degrees F (427 degrees C) during fabrication may impair corrosion resistance.
HISTORICAL
1945-05-01
Standard
AMS5560A
This specification covers a corrosion-resistant steel in the form of seamless tubing. This tubing has been used typically for parts, such as fluid-conducting lines, not subjected to high pressure and requiring good corrosion resistance, but usage is not limited to such applications. Welding, brazing, or other exposure to temperatures over 800 °F (427 °C) during fabrication may impair corrosion resistance.
HISTORICAL
1945-05-01
Standard
AMS6274C
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
HISTORICAL
1945-05-01
Standard
AMS3198B
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, medium sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS3199B
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, firm sponge rubber pads and seals operating from -40 to +80 degrees C (-40 to +176 degrees F), but usage is not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS3197B
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered. These products have been used typically for general applications requiring the use of open-cell, soft rubber sponge pads and seals operating from -40 to +176 °F (-40 to +80 °C), but usage is not limited to such applications.
HISTORICAL
1945-05-01
Standard
AMS2243
This specification covers manufacturing tolerances applicable to seamless and welded tubing of corrosion and heat-resistant steel ordered to inch dimensions. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. Tubing may be specified by two dimensions only (OD and wall thickness, ID and wall thickness, or OD and ID).
HISTORICAL
1945-05-01
Standard
AMS5645C
This specification covers a corrosion and heat resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
HISTORICAL
1945-05-01
Standard
AMS5640B
This specification covers three types of a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
HISTORICAL
1945-05-01
Standard
AMS6260B
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
HISTORICAL
1944-11-01
Standard
AMS3420A
This specification covers silica gel dehydrating agent in the form of a granular powder in either plain or indicator grades. Indicator grades shall be impregnated with cobalt chloride.
HISTORICAL
1944-11-01
Standard
AMS3554
HISTORICAL
1944-11-01
Standard
AMS6342
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
HISTORICAL
1944-11-01
Standard
AMS4803
This specification covers a zinc alloy in the form of die castings.
HISTORICAL
1944-11-01
Standard
AMS6282
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
HISTORICAL
1944-11-01
Standard
AMS5050B
This specification covers a low-carbon steel in the form of seamless tubing. This tubing has been used typically for oil lines and other parts requiring high-quality tubing suitable for severe forming and for welding or brazing, but usage is not limited to such applications.
Viewing 19981 to 20010 of 20532