Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 31 to 60 of 20301
CURRENT
2017-06-13
Standard
AMS5826E
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
2017-06-13
WIP Standard
B17AD
Specification to cover the technical requirements for a high density ceramic peening media.
2017-06-13
WIP Standard
J2932
This document provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability and environmental performance when tested according to SAE J2902.
CURRENT
2017-06-13
Standard
AMSA21180C
This specification covers the requirements for six alloy compositions, four inspection classes, four radiographic quality grades and six classes of mechanical properties of high strength aluminum-alloy castings.
CURRENT
2017-06-12
Standard
AS7106/2B
This document has been declared "CANCELLED" as of June 2017. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index. Cancelled specifications are available from SAE.
CURRENT
2017-06-09
Standard
AMS4352J
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles up to 40 in2 (258 cm2) in cross-sectional area (solids) and up to 8.5 inches (216 mm) OD by 1.188 inches (30.18 mm) wall thickness (tubing) (see 8.4).
CURRENT
2017-06-09
Standard
AMS1424N
This foundation specification (AMS1424N) and its associated category specifications (AMS1424/1 and AMS1424/2) cover a deicing/anti-icing material in the form of a fluid.
CURRENT
2017-06-09
Standard
ARP4912C
This SAE Aerospace Recommended Practice (ARP) provides recommendations on cavity design, the installation of elastomer type spare seals in these cavities, and information surrounding elastomer material properties after contact with typical shock absorber hydraulic fluid(s) or grease. This ARP is primarily concerned with the use of spare seals on shock absorbers where only a single dynamic seal is fitted and in contact with the slider/shock absorber piston at any one time. These shock absorbers typically have a spare (dynamic) seal gland located on the outer diameter of the lower seal carrier. This spare seal gland is intended to house a spare elastomer contact seal. Split Polytetrafluoroethylene (PTFE) backup rings can also be installed in the spare seal cavity. During operation, if the fitted dynamic shock absorber standard seal begins to fail/leak, then the aircraft can be jacked up, allowing the lower gland nut of the shock absorber to be dropped down.
CURRENT
2017-06-08
Standard
AS7109/7B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/7. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/7. Cancelled specifications are available from SAE.
CURRENT
2017-06-08
Standard
AS7109/6B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/6. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/6. Cancelled specifications are available from SAE.
2017-06-07
WIP Standard
AS8010D
This document defines the minimum degree of purity and maximum levels of certain deleterious impurities allowable for aviator's breathing oxygen at the point of manufacture or generation. It covers gaseous, liquid, and chemically generated oxygen, and oxygen supplied by in situ concentration and in situ electrolysis. Different limits are established for oxygen from different sources, in recognition of differences in the ways the oxygen is stored, dispensed, and utilized, taking into account the safety of the user. These limits are not intended to specifically reflect upon the relative capabilities or merits of various technologies. Procurement documents may specify more stringent limits, where required for specific applications. Medical oxygen is not covered by this standard. In the United States, medical oxygen is a prescription drug.
CURRENT
2017-06-07
Standard
AS7109/4B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/4. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/4. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/5B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/5. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/5. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/1B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/1. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/1. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/3B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/3. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/3. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/2B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/2. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/2. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
J948_201706
These methods of test are applicable for determining the resistance to snagging and abrasion of automotive bodycloth, vinyl, and leather.
CURRENT
2017-06-07
Standard
J811_201706
This SAE Information Report covers applications of mechanical prestressing, improving fatigue resistance, theory of surface rolling for fatigue improvement, calculations for the surface rolling process, tooling for surface rolling, control and inspection, effect of surface rolling on properties other than fatigue, and other methods for mechanical prestressing.
2017-06-06
WIP Standard
GA-E17AB
General Agreement to give guidance on utility of previous revision material in stock.
CURRENT
2017-06-05
Standard
AIR4938B
This is a general curriculum that has been developed to identify the minimum knowledge and skill requirements of a composite and/or metal bond repair technician/specialist. This revision changes the document from an all-inclusive curriculum into a modular set of curricula. Teaching levels have been assigned to the curriculum to define the knowledge, skills and abilities graduates will need to make composite repairs. Minimum hours of instruction have been provided to ensure adequate coverage of all subject matter - lecture and laboratory. These minimums may be exceeded, and may include an increase in the total number of training hours and/or increases in the teaching levels.
CURRENT
2017-06-05
Standard
AMS4966R
This specification covers a titanium alloy in the form of forgings and forging stock. These forgings have been used typically for parts requiring strength up to 800 °F (427 °C) and that may be welded during fabrication, but usage is not limited to such applications.
CURRENT
2017-06-05
Standard
AMS5802E
This specification covers a corrosion and heat-resistant iron-nickel alloy in the form of welding wire.
CURRENT
2017-06-05
Standard
AMS7445E
This specification covers balls made of high-carbon corrosion-resistant steel of three carbon ranges.

These products have been used typically for bearing balls, but usage is not limited to such applications.

CURRENT
2017-06-05
Standard
AS14227D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-05
Standard
AS5620B
This SAE Aerospace Standard (AS) shall be used in conjunction with AMS 4946 to provide requirements for qualification testing and for Qualified Products Listing (QPL) and Qualified Manufacturer Listing (QML) for Ti-3Al-2.5V cold worked and stress relieved hydraulic system tubing. The basic tubing shall comply with the requirements of AMS 4946.
2017-06-01
WIP Standard
AMS4368
This new draft specification is for an aluminum material hot isostatically pressed from 6061B aluminum powder, each powder particle discontinuously reinforced with silicon carbide particulate.
CURRENT
2017-06-01
Standard
AMS5357D
This specification covers a corrosion-resistant steel in the form of investment castings.
CURRENT
2017-06-01
Standard
AMS1548B
This specification covers a solvent-emulsion cleaner in the form of a solvent-base liquid concentrate.
CURRENT
2017-06-01
Standard
AMS7510/2C
This specification covers one type of samarium-cobalt permanent magnets.
CURRENT
2017-06-01
Standard
AS1005H
SCOPE IS UNAVAILABLE.
Viewing 31 to 60 of 20301