Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 271 to 300 of 20547
CURRENT
2017-08-17
Standard
AMS3793/3C
This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights.
CURRENT
2017-08-17
Standard
AMS4553D
This specification covers a copper alloy (brass) in the form of seamless tubing with nominal OD of 0.405 inch (10.29 mm) to 10.75 inches (273.05 mm) and nominal weight of 0.253 lb/ft (0.38 kg/m) to 2.176 lb/ft (3.24 kg/m) (see 8.6).
CURRENT
2017-08-17
Standard
AMS6528D
This specification covers a special aircraft-quality, low-alloy steel in the form of bars.
CURRENT
2017-08-17
Standard
AMS7464D
This specification covers premium quality bolts and screws made from a low-alloy, heat-resistant steel and having threads of UNJ (MIL-S-8879) form.
CURRENT
2017-08-15
Standard
AMS6330J
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-08-15
Standard
AMS6523H
This specification covers a premium aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
CURRENT
2017-08-15
Standard
AS31031B
SCOPE IS UNAVAILABLE.
CURRENT
2017-08-15
Standard
AMS5042N
This specification covers a carbon steel in the form of sheet and strip.
CURRENT
2017-08-15
Standard
AMS5030K
This specification covers a low-carbon steel in the form of welding wire.
CURRENT
2017-08-15
Standard
AMS5115J
This specification covers a carbon steel in the form of wire supplied as coils of wire or as finished springs.
CURRENT
2017-08-15
Standard
ARP1876C
This SAE Aerospace Recommended Practice defines a method for determining the weldability of weld filler metal in continuous coil or cut length form. It is applicable to all solid (non flux-containing) wires. It is intended as a referee method for testing weld filler metals in case of dispute between purchaser and vendor.
CURRENT
2017-08-14
Standard
AMS4712G
This specification covers a copper-zinc alloy (brass) in the form of wire.
CURRENT
2017-08-14
Standard
J1355_201708
This SAE Recommended Practice describes a laboratory test procedure for measuring the thickness of various resilient insulating padding materials that are used in the automotive industry. Such padding materials may include synthetic or non-synthetic materials, fibrous or cellular materials, high loft or compressed materials, single layer homogeneous or multilayer products, low and high surface density products. Some of these samples may be deformable and elastic, high loft thermal and acoustical fibrous materials, as well. The test method described herein has been developed to establish a means of a uniform procedure for measuring the thickness of different types of samples not only for application to all ground vehicles, but also may be applicable to other situations or conditions. The test method is designed to measure the thickness of flat samples and not formed parts. This test method does not purport to address all of the safety concerns, if any, associated with its use.
CURRENT
2017-08-14
Standard
AMS5061H
This specification covers a low-carbon steel in the form of bars and wire 0,750 inch (19.05 mm) and under in nominal diameter or distance between parallel sides.
CURRENT
2017-08-14
Standard
AMS7301J
This specification covers low-alloy steel springs made of annealed round wire heat treated after forming.
CURRENT
2017-08-14
Standard
AMS2376E
This specification covers procedures for approval of premium-quality forgings, usually serialized, the stock from which such forgings are produced, and the controls to be exercised in producing the forgings and forging stock.
CURRENT
2017-08-14
Standard
AMS5062J
This specification covers low-carbon steel in the form of bars, forgings, mechanical tubing, sheet, strip, plate, and forging stock.
CURRENT
2017-08-14
Standard
J2927_201708
This SAE standard applies to refrigerant identification equipment to be used for identifying an acceptable level of R-1234yf purity in a refrigerant tank or vehicle MAC system labeled as containing R-1234yf, and not misidentify other refrigerants, per 5.7.
CURRENT
2017-08-14
Standard
J1204_201708
This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway service on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light truck wheels (inset less than 0.10 m) to this trailer service, use this procedure. For the application of heavier truck wheels (inset 0.10 m (or more)) use SAE J267. Mobile home service is outside the scope of this document. There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel.
CURRENT
2017-08-11
Standard
J2846_201708
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated.
CURRENT
2017-08-10
Standard
AMS5540P
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, and plate up to 2 inches (50.8 mm), inclusive, in nominal thickness (see 8.4).
2017-08-08
WIP Standard
AMS3085B
This specification covers a neopentyl polyol ester fluid (see 8.2) with AS5780 HPC or MIL-PRF-23699 HTS Class performance.
2017-08-07
WIP Standard
GA-F17AB
Chemical Analysis Revision
CURRENT
2017-08-07
Standard
AMS4485A
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles from 0.039 to 4.75 inches, incl. (12.71.0 to 120.7 mm., incl.) in nominal thickness (see 8.4).
CURRENT
2017-08-07
Standard
AMS4993F
This specification covers a titanium alloy in the form of compacts produced by pressing and sintering a blend of elemental titanium powder and aluminum vanadium alloy powder.
CURRENT
2017-08-07
Standard
J576_201708
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes additional performance requirements and provides test methods and requirements to evaluate the suitability of plastic material or materials intended for optical applications in motor vehicles. The tests are intended to determine physical and optical characteristics of the material or materials only. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment.
CURRENT
2017-08-07
Standard
AMSQQW428/1B
Viewing 271 to 300 of 20547