Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 11049
2017-12-07
WIP Standard
ARP7488
This Aerospace Recommended Practice (ARP) describes design and processing considerations for the shot peening process when AMS2430 or AMS2432 are specified.
CURRENT
2017-12-07
Standard
AMS4434N
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-12-07
Standard
AMS4958E
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter.
CURRENT
2017-12-07
Standard
AMS5532H
This specification covers a corrosion and heat-resistant iron alloy in the form of sheet, strip, and plate.
CURRENT
2017-12-07
Standard
AMS5537J
This specification covers a corrosion and heat-resistant cobalt alloy in the form of sheet, strip, foil, and plate up to 2.250 inches (57.15 mm) inclusive, in nominal thickness (see 8.4).
CURRENT
2017-12-07
Standard
AMSQQA200/7C
This specification covers the specific requirements for aluminum alloy 5456 bar, rod, shapes, tube, and wire produced by extrusion.
CURRENT
2017-12-07
Standard
AS1650E
This SAE Aerospace Standard (AS) defines the requirements for a threadless, flexible, self-bonding coupling assembly which, when installed on machined fixed cavity ferrules, provides a flexible connection for joining tubing and components in aircraft fuel, vent or other systems. This assembled coupling, hereafter referred to as the assembly, and is designed for use from -65 to +400 °F and at 125 psig nominal operating pressure. AS1650 was not designed for the new certification requirements for flammable leakage zones and fuel tanks for lightning protection and assembly redundancy. As such their use and installation may require additional efforts and equipment to support new FAA CFR compliance. The AS7510 flexible coupling should be the preferred coupling for use in flammable leakage zones and fuel tanks that require service life and functionality for lightning protection and part redundancy.
CURRENT
2017-12-07
Standard
AMS5350K
This specification covers a corrosion and moderate heat-resistant steel in the form of investment castings.
CURRENT
2017-12-07
Standard
AMS6349E
This specification covers an aircraft quality, low alloy steel in the form of bars.
CURRENT
2017-12-07
Standard
AMS6452E
This specification covers a low-alloy steel in the form of welding wire.
CURRENT
2017-12-07
Standard
AMSQQA200/6C
This specification covers the specific requirements for aluminum alloy 5454 bar, rod, shapes, tube, and wire produced by extrusion.
CURRENT
2017-12-07
Standard
AMS6931D
This specification covers a titanium alloy in the form of bars and forgings up through 10.000 inches (254.00. mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 79.0 in2 (506.45 cm2) and forging stock of any size (see 8.7).
CURRENT
2017-12-07
Standard
AMS4035M
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.750 inch (0.25 to 44.45 mm) in thickness, supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper.
CURRENT
2017-12-07
Standard
AMS4928W
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings, drawn shapes up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides and stock of any size for forging or flash welded rings.
CURRENT
2017-12-05
Standard
AMS6466G

This specification covers a corrosion-resistant steel in the form of welding wire.

2017-12-01
WIP Standard
AMS3021F
This specification covers a neopentyl polyol ester fluid.
2017-11-30
WIP Standard
AMS03_14A
This SAE Standard gives guidance for - and specifies the requirements for - the electrodeposition of chromium for engineering purposes. It relates to both new articles and also the reclamation of worn or over-machined components. Chromium electrodeposition undertaken for decorative purposes is not considered herein.
2017-11-30
WIP Standard
AMS03_17A
This SAE Standard specifies the requirements for the electro-deposition of gold on ferrous-base materials, copper-base materials, aluminum-base materials, zinc-base materials and nickel-base materials for MOD use. It is primarily intended for use on electrical and electronic items which are to be plated with gold to: a. Increase the electrical conductivity of the surface. b. Provide a solderable surface. This Standard does not cover the gold plating of threaded items.
2017-11-30
WIP Standard
AMS03_18A
This SAE Standard specifies the properties of chromate conversion coatings on aluminum and aluminum alloys. It details inspection and testing requirements for chromate conversion coatings. Where there are differences in the requirements for the Brushing Grade from the Standard Grade they are highlighted in this Standard.
CURRENT
2017-11-30
Standard
AMS4268A
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.500 inch (0.254 to 38.07 mm), inclusive, in thickness, supplied in the -T81/-T851 temper (see 8.5).
CURRENT
2017-11-30
Standard
AMSS6758B
This specification covers chrome-molybdenum (4130) steel bars and forging stock of aircraft quality.
CURRENT
2017-11-30
Standard
AMS6457E
This specification covers a low alloy steel in the form of welding wire.
CURRENT
2017-11-29
Standard
AMS3731/10C
This specification covers an unfilled, room-temperature-polymerizing epoxy resin formulation with a polyamide hardener, supplied as a two-component system.
CURRENT
2017-11-29
Standard
AMS2545
This specification covers the requirements for saturation peening, straightening and forming metal parts using controlled pneumatic activated needles.
CURRENT
2017-11-28
Standard
AMS3056C
This specification covers the requirements for a refined paraffinic petroleum-base lubricant.
2017-11-27
WIP Standard
AMS6952
This specification covers a titnaium alloy in the form of forgings 4.4 inches (111.76 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
CURRENT
2017-11-21
Standard
AMS3329C
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
CURRENT
2017-11-21
Standard
AMS3330C
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
Viewing 1 to 30 of 11049

Filter

  • Standard
    11049