Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 379
CURRENT
2016-11-01
Standard
J2580_201611
This Recommended Practice covers air braked trucks, truck-tractors, trailers and buses. It enumerates the identification and installation of the air brake components not covered in other SAE recommended practices and standards.
CURRENT
2016-10-13
Standard
J2892_201610
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
2016-05-10
WIP Standard
J1817
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
CURRENT
2016-03-15
Standard
J1817_201603
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
CURRENT
2015-11-19
Standard
J2224_201511
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
2015-09-29
WIP Standard
J386
This standard provides performance and test requirements for operator restraint systems provided for off-road self-propelled work machines. This document applies to pelvic restraint systems (Type 1) for off-road, self-propelled work machines fitted with ROPS and commonly used in construction, earthmoving, forestry, and mining as referred to in SAE J1040 and industrial machines fitted with ROPS as referred to in SAE J1042.
2015-09-23
WIP Standard
J747
This SAE Standard applies to hydraulic directional control valves as applied to self-propelled work machines referenced in SAE J1116. It describes a laboratory test procedure for evaluating: a.) Flow versus pressure drop, b.) Leakage rate, c.) Operating effort, d.) Metering characteristics versus spool travel, pilot pressure, or electrical current, e.) Relief valve characteristics. This document applies to single and multiple section hydraulic directional control valves. This document illustrates axial, manually operated valves although the test procedure is applicable to other input forms such as rotary actuation, electric current, hydraulic or pneumatic pressure.
CURRENT
2015-05-12
Standard
J1449_201505
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
CURRENT
2015-03-27
Standard
J2130/2_201503
This SAE Standard applies to all self-propelled machines with a gross vehicle mass up to 5000 kg that are utilized to clean material from outside paved areas, parkland, floors in non-residential buildings and areas principally exposed to pedestrian traffic. Primary methods for material removal can be by mechanical, pneumatic, washing and flushing systems, or in a combination of any system.
CURRENT
2015-03-27
Standard
J2130/1_201503
This SAE Standard applies to all self-propelled machines with a gross vehicle mass greater than 5000 kg that are utilized to clean material from highways, parking lots, airfield runways, outside paved areas that are principally exposed to vehicular traffic. These machines can also be involved with road construction or repaving work. Primary methods for material removal and cleaning can be by mechanical, pneumatic, washing and flushing systems, or in a combination of any system.
CURRENT
2015-03-01
Standard
EIA933B
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets; as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as small electronic assemblies such as printed wiring assemblies, relays, disk drives, LCD matrices, VME circuit cards, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, and qualification methods are at least partially controlled, or influenced, by aerospace customers (either individually or collectively). An example at this end of the spectrum is a VME circuit card assembly.
CURRENT
2015-02-26
Standard
J2593_201502
This information report provides general information for installing and tightening fluid conductors and connectors. Following these guidelines, with the consistent proper use of torque wrenches, tightening procedures and correct torque levels will result in diminishing leaks and improving service life by avoiding hose twisting, tube binding, false torque and improper joint closures. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, this report should not be used as a “standard” nor a “specification” and the values shown should not be construed as “guaranteed” minimums, maximums or absolutes. This document is an information report to help users by gathering available information from the various connector standards and publishing the information in one source for easy retrieval and applied common usage. This information report is primarily intended for mobile/stationary industrial equipment applications.
2015-01-08
WIP Standard
J2267
This SAE standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include: Front guards for yarders with cabs mounted next to the tower; Front guards for forestry machines capable of handling material in front of and above the deflection limiting volume (DLV); such as knuckle boom log loaders and swing to tree feller bunchers; but excluding rubber-tired or tracked front-end loaders when equipped with buckets or forks with hold down grapple arm(s); and excluding forwarders and clambunk skidders fitted with load bunk headboards meeting the requirements of ISO 11850.
CURRENT
2014-10-21
Standard
J2417_201410
This SAE Standard provides a uniform method to calculate the lift capacity of knuckle-boom log loaders and certain forestry equipment. It establishes definitions and specifies machine conditions for calculations. This document applies to knuckle-boom log loaders as defined in ISO 6814 and ISO 17591 and certain forestry equipment defined in ISO 6814 that have a rotating upper-structure such as feller bunchers, forwarders, harvesters, and behind the cab or rear-mounted knuckle-boom log loaders not having their own power supply. It does not apply to harvesters that are incapable of lifting a tree or log completely off the ground. This document applies to those machines that are crawler, rubber-tired, and pedestal or stationary mounted.
CURRENT
2014-09-09
Standard
J176_201409
This SAE Standard applies to off-road self-propelled work machines as categorized in SAE J1116. Fast fill fueling typically applies to self-propelled machines with a fuel capacity over 380 L, although fast fill fueling can be used on machines with smaller fuel capacity.
2014-08-20
WIP Standard
J1014
This SAE Standard includes only those towing winches commonly used on skidders and crawler tractors. These winches are used on self-propelled machines described in SAE J1057; J1116; and J1209. Specifically excluded are those winches used for hoisting operations. This document classifies the major types of winch and establishes nomenclature for major winch components. Examples used here are not intended to include all existing winches nor to be descriptive of any particular winch.
CURRENT
2014-06-26
Standard
J1071_201406
This SAE Standard covers the relative position and direction of motion of controls which influence the movement of the machine and the operating direction only of equipment controls. There is no intention to eliminate or restrict the use of combination controls, automatic controls, or special operating controls. Purpose This document is intended as a guide for designing uniform operator controls for graders. Graders are defined in SAE J/ISO 6165.
CURRENT
2014-05-07
Standard
J1702_201405
This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper.
CURRENT
2014-01-08
Standard
J738_201401
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: Scrapers as defined in ISO 7133. Dozers as described in ISO 6747. Loaders as described in ISO 7131. Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
CURRENT
2013-11-13
Standard
J1091_201311
This SAE Standard specifies a stationary test method for determining the masking effect caused by parts of the base machine with equipment as specified by the manufacturer on a visibility test circle around the machine from the eye position point of a seated operator. It specifies a method for evaluating the maskings that may be present. It applies to earthmoving machines which have a specific operator’s station. It does not consider evaluation of maskings which may be present with operational movement of working tools.
CURRENT
2013-11-13
Standard
J2331_201311
This SAE Standard specifies a stationary test method for determining and documenting the masking effect caused by parts of the base machine with equipment as specified by the manufacturer within a visibility test circle around the eye position of a seated operator. It applies to earthmoving machinery which has a specific seated operator’s position.
CURRENT
2013-10-29
Standard
J920_201310
This Recommended Practice applies to technical publications which present instructions for the proper unloading, set-up, installations, pre-delivery inspection, operation, and servicing of off-road self-propelled work machines as categorized in SAE J1116. Advertising/marketing and other pre-purchase publications are not included.
CURRENT
2013-10-21
Standard
J1353_201310
This SAE Recommended Practice identifies major components and parts peculiar to clam bunk skidders. Illustrations used here are not intended to include all existing machines or to be exactly descriptive of any particular machine. They have been provided to illustrate the principles to be used in applying this document.
2013-10-02
WIP Standard
J153
These general operator precautions apply to off-road work machines as defined in SAE J1116, and Agricultural Tractors as defined in ANSI/ASAE S390, Nov 2004. These should not be considered as all inclusive for all specific uses and unique features of each particular machine. Other more specific operator precautions not mentioned herein should be covered by users of this recommended practice for each particular machine application.
2013-10-01
WIP Standard
J1533
This SAE Recommended Practice establishes a uniform test procedure for determining performance levels of operator enclosure panel type air filters on off-road, self-propelled work machines used in construction, general-purpose industrial, agriculture, and forestry as defined in SAE J1116 and equipped with an operator enclosure with a powered fresh air system.
2013-09-30
WIP Standard
J169
The purpose of this document is to establish air conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system, and since these characteristics and conditions vary greatly from one application to another, the designer must determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in this document.
CURRENT
2013-09-25
Standard
J1111_201309
This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document
CURRENT
2013-08-21
Standard
J1360_201308
This standard covers self-propelled off-road work machines as categorized in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
CURRENT
2013-08-05
Standard
J1051_201308
This SAE Standard provides a method to obtain consistent force-deflection data of finished (or unfinished, when specified) cushioned components of seats for off-road work machines as listed in SAE J1116. This data may be helpful in maintaining seat comfort characteristics and quality control. There is no intent to establish any acceptance criteria.
Viewing 1 to 30 of 379