Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 241 to 270 of 9893
CURRENT
2016-11-22
Standard
AMS5441B
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings 5 inches (127 mm) and under in nominal diameter or least distance between parallel sides and up to 50 in2 (323 cm2) in cross-sectional area, and stock of any size for forging, flash welded rings, or heading (see 8.5).
CURRENT
2016-11-22
Standard
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
CURRENT
2016-11-18
Standard
J485_201611
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
CURRENT
2016-11-18
Standard
AMS3755D
This specification and its supplementary detail specifications cover silicon dioxide in the form of a white, amorphous powder.
CURRENT
2016-11-18
Standard
AMS3755/1B
This specification covers one type of silicon dioxide in the form of a white, anhydrous powder with high thickening efficiency.
CURRENT
2016-11-18
Standard
J1053_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
CURRENT
2016-11-18
Standard
J1053M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
CURRENT
2016-11-15
Standard
AMS2590A
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic Almen test strip holder is required for intensity determination.
CURRENT
2016-11-14
Standard
AMS4273D
This specification covers an aluminum alloy in the form of sheet and plate.
CURRENT
2016-11-14
Standard
AMS4270C
This specification covers an aluminum alloy in the form of sheet clad on both sides with a different aluminum alloy.
2016-11-11
WIP Standard
AS5385D
This Standard aims at identifying the design criteria and testing methods adequate to guarantee the ultimate load and operational dependability of cargo restraint strap assemblies with a typical 22,250 N (5,000 lbf) rated ultimate tension load capability, as used by the airline industry in order to restrain on board civil transport aircraft during flight: a. cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into aircraft lower deck or main/upper deck cargo systems and meeting the requirements of NAS 3610 or AS36100, or b. non-unitized individual pieces of cargo, or pieces of, cargo placed onto an unrestrained ( "floating ") pallet into either lower deck or main deck containerized cargo compartments of an aircraft.
CURRENT
2016-11-10
Standard
AMS2252E
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range.
2016-11-09
WIP Standard
AMS6452E
This specification covers a low-alloy steel in the form of welding wire.
2016-11-09
WIP Standard
AMS6453D
This specification covers a low-alloy steel in the form of welding wire.
2016-11-09
WIP Standard
AMS6459F
This specification covers a low-alloy steel in the form of welding wire.
2016-11-09
WIP Standard
AMS6501E
This specification covers a maraging steel in the form of welding wire.
CURRENT
2016-11-08
Standard
AS9145
This standard establishes requirements for performing and documenting APQP and PPAP. APQP begins with conceptual product needs and extends through product definition, production planning, product and process validation (i.e., PPAP), product use, and post-delivery service. This standard integrates and collaborates with the requirements of the 9100, 9102, 9103, and 9110 standards. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2016-11-07
Standard
AMS6520E
This specification covers a premium aircraft-quality, maraging steel in the form of sheet, strip, and plate.
CURRENT
2016-11-01
Standard
J2580_201611
This Recommended Practice covers air braked trucks, truck-tractors, trailers and buses. It enumerates the identification and installation of the air brake components not covered in other SAE recommended practices and standards.
CURRENT
2016-10-31
Standard
AMS6461L
This specification covers a low-alloy steel in the form of welding wire.
2016-10-27
WIP Standard
AMS7004
This specification covers titanium 6Al-4V preforms fabricated using Rapid Plasma Deposition™ (RPD™) additive manufacturing process on a Ti-6Al-4V substrate that are subject to post deposition stress relieve.
CURRENT
2016-10-26
Standard
AMS6462K
This specification covers a low-alloy steel in the form of welding wire.
CURRENT
2016-10-26
Standard
AMS6469E
This specification covers a low-alloy steel in the form of welding wire.
2016-10-21
WIP Standard
AMS4917J
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2016-10-19
WIP Standard
AMS2750F
This specification covers pyrometric requirements for thermal processing equipment used for heat treatment. It covers temperature sensors, instrumentation, thermal processing equipment, system accuracy tests, and temperature uniformity surveys. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification(s).
2016-10-16
WIP Standard
B16AD
AMS specification that defaults to an appropriate AWS specification for the technical requirements but has the QA requirements from AMS2680. AMS2680 would then be stabilized and point to the new AMS. This specification should be titled B16AD for balloting purposes.
CURRENT
2016-10-13
Standard
J2892_201610
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
2016-10-11
WIP Standard
AMS7875F
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder. This product has been used typically for producing plasma spray coatings to provide wear and fretting resistant surfaces, but usage is not limited to such applications.
2016-10-10
WIP Standard
AMS4966R
This specification covers a titanium alloy in the form of forgings and forging stock. These forgings have been used typically for parts requiring strength up to 800 °F (427 °C) and that may be welded during fabrication, but usage is not limited to such applications.
2016-10-08
WIP Standard
AMS4998F
This specification covers a titanium alloy in the form of prealloyed powder. This powder has been used typically for compaction into net or near net shapes and into forging stock in the form of billets or preforms, but usage is not limited to such applications.
Viewing 241 to 270 of 9893